Repairing Guides

how much does it cost to repair cv axle

by Della White MD Published 3 years ago Updated 2 years ago
image

The Average Cost for Replacing a CV Axle Is $137 to $672 Depending on if You Go to the Mechanic or DIY. This price range is based on national averages for all vehicles and does not factor in taxes, fees, or your particular make and model.Apr 22, 2022

Full Answer

How much does it cost to replace a CV axle?

CV Axle Replacement Cost Estimates The average cost for a CV Axle Replacement is between $945 and $1,074 but can vary from car to car. Repairs commonly associated with CV axle replacement

What causes a CV axle to go bad?

  • How to tell the difference between bad wheel bearing bad CV joint
  • Is CVT Better Than Automatic Transmission (See Pros & Cons)
  • 5 Bad Front Wheel Bearing Symptoms

What are the symptoms of a bad CV axle?

com One of the most common and most noticeable symptoms of a bad or failing CV axle shaft assembly is an audible clicking noise when turning.

How to diagnose a bad CV axle?

clicking sound when turning: the most common symptom of a bad cv axle is a clicking noise when turning. this is most often heard during sharp turns at lower speeds. typically this indicates an issue with the outer cv joint, and the sound is the loudest on the joint that’s opposite of the turning direction.

image

Is a CV joint expensive to fix?

The average CV joint replacement cost is between $150 and $850, depending on the car model and labor costs. The CV joint price is between $50 and 150$, while the labor cost of a CV Joint replacement is between $100 and $700. Several factors will affect the total cost if you need to get your vehicle's CV joint replaced.

How much does it cost to replace Axel?

On average, you can expect it to cost between $880 and $959 to replace your car axle shaft, depending on the type of car you drive and which axle is broken. However, it's possible that you'll just need to repair your axle rather than replace it.

Can a CV axle be repaired?

While one can repack, reboot and rebuild CV axles, it makes more sense for the average do-it-yourselfer to procure replacement units and swap out the old axles. If a boot is torn or missing, it is possible to save the joint if caught early enough, but usually the damage has already been done.

Can you drive with a damaged CV axle?

A severely worn out CV joint can even disintegrate while you're driving and make the car undrivable. You may lose control of the vehicle entirely. It is not safe to drive with a damaged CV joint. Look for some symptoms of a failing CV joint to have it repaired before it becomes unsafe to operate the vehicle.

Is CV joint and CV axle the same thing?

A CV axle has two CV joints (an inner joint and an outer joint). These joints allow the axle to transfer the engine's power to the drive wheels at a constant speed while accommodating for the different travel conditions, including the up and down motion of the suspension and cornering.

How long does it take to Change CV axle?

On the 2006 Navigator, if a professional mechanic is replacing the axle(s), it is assumed to take about 1 hour to replace one axle (i.e., one side) whether it is the rear axle or the front axle.

What causes a CV axle to break?

Why do CV joints break? The main culprit is shock loading, like when a spinning wheel lifts off the ground and then lands hard; something that can happen fairly often with an independent suspension system because of the usually limited amount of travel.

How urgent is CV joint?

Failing CV joints pose a serious risk so be sure to get your car into your auto shop as soon as possible. If there is only a small crack in the outer CV joint, your mechanic may be able to simply replace the CV boot and repack the grease, but for any major damage, an entirely new joint is necessary.

Should I replace both CV axles at the same time?

On a high-mileage vehicle with a bad CV joint or boot, it's often a good idea to replace both shafts at the same time. Often, the right (passenger side) shaft fails first because right turns are at a sharper angle than left turns, and right turns are more common than left turns.

Are axles expensive?

The cost to repair an axle runs between about $500 and $600 dollars before taxes and fees. Costs vary depending the type of vehicle, brand, make, and model. Labor costs vary from between about $50 dollars and $140 depending on how long the job takes for a model of vehicle.

What happens if you don't replace CV axle?

The Constant Velocity is sealed by a boot. This boot may get damaged, and when this happens, the joint will wear out and eventually fail. If you drive a car with a damaged CV, the joint will disintegrate further, making driving impossible. You'll not be able to control the vehicle and may get involved in an accident.

How do you know if your CV axle is going out?

These are the 5 easiest ways to identify if you have a damaged CV axle.A Tear in the Boot.Grease Found on the Inside of Your Wheels. ... Knocking Sound. ... Clicking While Turning. ... Vibration While Driving. ...

How much does it cost to replace an axle on a horse trailer?

Torsion axle replacement will run between $500 & $700 depending which axle you have. You have probably bent the spindle which will cause the odd tire wear.

How much is a driver side CV axle?

CV Axle Replacement Expenses Replacement axle shafts can be bought for between $60-150.00 each, and labor is generally between 1.5-3 hours to replace, bringing labor to around $150-350.00.

How do you know if your CV axle is going out?

These are the 5 easiest ways to identify if you have a damaged CV axle.A Tear in the Boot.Grease Found on the Inside of Your Wheels. ... Knocking Sound. ... Clicking While Turning. ... Vibration While Driving. ...

How do you replace a utility trailer axle?

0:3612:31How to Replace Trailer Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we start by breaking the lugs loose just like you would on a flat tire then we're going to takeMoreSo we start by breaking the lugs loose just like you would on a flat tire then we're going to take off the other side the other tire as well then we'll jack this trailer up set it on blocks.

Side Mirror Replacement Cost Comparison

Below are a list of sample costs from the leading garage chains in the USA. Expect the price you pay to be different depending on where you live an...

When Should You Have The Cv Axle replaced?

Every time you receive a service the mechanic should examine this part to check it is not damaged. Because of the importance of the part, if it is...

What Is Done When An Axle Is replaced?

You need to confirm that the axles do need replacing before they are replaced. it might be that you can just replace one of the boots saving yourse...

How to Save Money on Cv Axle Replacement

If you have pitting in the joint section you may be able to avoid a replacement by swapping the joints on the driver’s side with the opposite side....

Sample Costs For Replacing A Cv Axle

We’ve compiled some costs for having the CV Axle replaced on a range of popular car models to help give you an idea of what you’ll pay for your car...

How much does it cost to replace a CV axle?

But even still, you’re going to have to pay a pretty penny to replace the CV axle in your vehicle. On average, it costs car owners somewhere between $900 and $1,200—with between $760 and $1,030 of that going to parts and between $140 and $180 of it going to labor. This is obviously a lot of money for you to pay for a new CV axle.

What happens if you put off replacing a CV axle?

If you put off replacing a bad CV axle for too long, it’s going to force you to pay even more money to fix things like your steering system and your suspension system. This helps explain why it’s a job you need to schedule sooner than later despite the high CV axle cost.

How to tell if CV axle is bad?

By now, you know all about how important the CV axle in your car is. But what you might not know is how to tell whether or not you could have a bad CV axle on your hands. It’s important for you to find out the signs of a bad CV axle so that you’ll know how to spot it when it starts to give you fits. Check out a few of these signs below: 1 You hear loud clicking sounds coming from the direction of your CV axle, especially when you’re making turns in your vehicle 2 You see grease showing up on the edges of your car’s tires with that grease likely coming from a cracked or torn boot in your CV axle that is leaking grease 3 You feel your car vibrating when you’ve driving it and the vibrations appear to increase as you drive your car faster

Why does my CV axle make a clicking sound?

You hear loud clicking sounds coming from the direction of your CV axle, especially when you’re making turns in your vehicle. You see grease showing up on the edges of your car’s tires with that grease likely coming from a cracked or torn boot in your CV axle that is leaking grease.

What is CV axle?

CV axles are most often found in cars featuring front-wheel-drive systems, but it has also become more common to find them in all-wheel-drive and even rear-wheel-drive vehicles in some cases. The CV axle in your vehicle isn’t something that you’re going to see very often.

Can you drive in a car with a bad CV axle?

For all these reasons, you shouldn’t get into the habit of driving around in a car with a bad CV axle. While it might not be the worst thing in the world at first, it’s only going to be a matter of time before your bad CV axle breaks apart and causes serious complications.

Can CV axles fail?

But at the same time, it’s not out of the ordinary for a CV axle to fail. There is a CV joint boot within your CV axle that can crack or tear over time, and when that happens, it’ll sometimes lead to the joint wearing down on you altogether.

What is CV axle?

A CV Axle (or constant velocity axle) is an important part of a front wheel drive car’s mechanics. It aids with forward momentum and suspension by allowing the drive shaft to change length when going over uneven terrain. Without this the cars drive shaft would be likely to become damaged.

How to tell if CV axle is on its way out?

A sign that your CV axle may be on its way out is a “clanging” sound coming from your wheels when you drive. Other indications may be grease around the tires of your car or your car vibrating whilst you are driving. If playback doesn't begin shortly, try restarting your device.

Why do CV axles get worn?

Commonly the outside boots are the first to get damaged as these receive more exposure to moisture, road debris etc .

How to replace a faulty axle?

Replace the faulty axle with a new, working one. Or, if you are just replacing the boot, remove the axle and replace the boot. Replace the wheel. Check the tire pressure as this can be effected by the removal of the wheel. Finally, road test to make sure that everything is working correctly.

How to save money on auto boot?

Another way to save money is to perform the labor yourself. It is a fairly time consuming job, which is why labor costs tend to be higher at auto shops. As it happens, the cost to replace the boot once labor is factored in is not that much cheaper than replacing the entire part.

Does CV axle pitting affect it?

Effectively this means that the CV axle will be “spinning backwards” and the pitting won’t affect it. This will buy you some time as you will effectively get double the use out of the part. This is not advisable if you are having a garage do it though as labor charges are potentially high.

Should I replace both axles on a side that is damaged?

If you are not mechanically minded and have to get it done by a mechanic it is probably worth replacing both of the axles on the side that is damaged and replacing the entire part as this saves you having further labor charges down the line when the other axle eventually wears out.

How are CV axles rebuilt?

It’s important to note that the historically, CV axles were often rebuilt by the mechanic by replacing one of the 2 failed CV joints, putting on a new boot, and putting the axle back in. Over time, the cost of new CV axles being massed produced became a better, more cost-effective option than simply replacing the joint, ...

What is CV axle?

A CV axle is composed of 2 CV joints – an inner joint that couples to the transmission/differential, and an outer joint ...

How to tell if CV joint is failing?

This becomes very evident if the wobbling happens when you press on the gas, as the engine torque causes the axle to wobble. While under the vehicle, you can usually find out which axle is producing the wobble by grabbing the axle near the joint on both sides and push up and down, and side to side. If there’s any slop or movement in the axle, the axle is suspect.

How many CV joints are there in a CV axle?

A CV axle is composed of 2 CV joints – an inner joint that couples to the transmission/differential, and an outer joint that couples to the wheel hub. Both of these joints twist and turn while continuing to provide constant torque to the wheel, hence the name constant velocity joint. CV joints require good, ample grease to keep lubricated, ...

What happens if CV boot is torn?

Remember that once the CV boot gets torn, it’s only a matter of time before the axle fails. Failing to address the situation can lead to catastrophic failure of the axle, which as stated above, is a part that is in rotating motion.

What is CV joint?

The CV joint, along with the CV axle, is what drives the engine’s power, through the transmission, out to the vehicle’s wheels. In it’s early days, CV axles were used primarily for Front-Wheel-Drive vehicles, as both front CV axles drove power to the wheels, and were designed to be able to transmit torque at extreme angles, like steering, bumps, ...

How to check CV boots for cracks?

Cracks on the Boot. When doing an oil change, check your CV boots carefully by opening up the ribs of the “accordion” and looking for cracks. A broken boot will fling grease anywhere it can, so look for signs of grease around the joint. If you see any, it’s only a matter of time before the joint fails. 3.

How does CV axle work?

How does a CV Axle Assembly work? CV axles are different from the straight axles of old, where a pair of rods ran through a cylindrical tube, connected on one end to a gear box (differential), and, on the other end, to the wheel hub.

What is CV axle?

A CV axle assembly is a drivetrain component on a vehicle that delivers power from the transmission to the wheel. It is commonly used in front-wheel-drive systems, but can also be found on all-wheel-drive, and even some rear-wheel-drive vehicles with independent suspensions.

What is CV on a car?

The CV (constant velocity) joints near each end of the axle assembly slide back and forth inside a cup, or housing . The joints are lubricated with grease and sealed inside a pair of rubber boots. These boots hold the grease inside, and they keep the dirt and grime outside.

What happens if CV joint wears out?

If a CV joint boot cracks or tears, it is only a matter of time before the joint wears out. If a boot is compromised, it can be replaced. If the problem is recognized before other symptoms happen (clicking or clunking sounds when driving), the life of the axle can be prolonged.

What happens if you leave a CV joint on too long?

If left for too long, a CV joint can break apart, causing considerable damage to the steering and suspension and possibly a loss of control of the vehicle. At the least, the vehicle will be undrivable. The axle should be replaced sooner than later - before it fails.

Can a CV axle be reversed?

Once the process of breakdown in the CV joints begins, however, it does not reverse. The problem will continue to worsen.

Can you replace boots on CV axle?

Replacement of the boots on a CV axle requires that the entire assembly must be removed from the vehicle and disassembled. Because of this labor-intensive approach - and because there is no guarantee how long the joint may last after being compromised - many owners choose to have the entire assembly replaced instead.

What is CV axle?

CV axles are most commonly used on the front-wheel-drive vehicles to transfer engine power to the wheels. Some all-wheel-drive vehicles and rear-wheel-drive vehicles with independent rear suspensions also use CV axles to transfer engine power to the wheels. CV axles have an inner joint and an outer joint. Either the two CV joints on ...

How to replace an axle?

On most vehicles, to replace an axle, you have to disconnect a lower ball joint. Sometimes the whole knuckle has to be removed and sometimes the knuckle is disconnected at the strut. In any case, if an alignment is recommended, it’s probably a good idea to have it checked.

What is a CV joint?

CV joints use a rubber or silicon boot to hold the grease in the joint. Most CV joint failures begin with a split or torn boot – whether from ordinary wear and tear or getting torn from road debris. At that point, the grease slings out and road grime can enter.

How do axles work?

As with many things, it can vary a great deal with how the vehicle is driven. The axles transfer engine power to the wheels, and are more or less highly stressed depending on the driver’s relationship with the gas pedal.

What happens if the steering wheel is level before and level after?

If the steering wheel was level before and level after, probably, there was no change. PRO TIP – If the CV joint failure was because of the inner joint, engine mounts should be inspected and addressed as necessary. If an inner joint has failed, it should be kept in mind that these are sensitive to the engine position.

Do you need to align your wheels after a wheel replacement?

Often, a wheel alignment will be recommended after the axle replacement. There is a general rule that if any part of the suspension between the wheels is removed or replaced, the alignment should be checked. On most vehicles, to replace an axle, you have to disconnect a lower ball joint.

Can a double axle leak after a replacement?

In general, if that seal wasn’t leaking before the axle replacement, it probably won’t leak after. But the seal is easy to damage during installation and is usually pretty insignificant in cost, especially when compared to the cost of a double axle joint replacement.

How long is CV axle warranty?

A: CV axles are usually covered by the manufacturer’s powertrain warranty, which should have you covered for at least four to five years and 50,000 to 60,000 miles. As for whether or not the axle makes it past the warranty period, there are many factors that can impact its lifespan.

What is CV axle?

CV axles, or constant velocity axles, come into play. They allow the transmission to drive a car’s wheels and open up a range of motion with bearings. The CV axle is composed of those bearings and rubber boots that can wear out over time.

How to remove a wheel from a car?

Make sure the vehicle is in Park or that it is in gear with the parking brake set. Jack up the car and remove the wheel on the side where you will be working. Locate the axle nut. It will be in the direct center of the hub or wheel assembly where you removed the wheel .

Can you spray a rusted axle nut?

You can spray it with lubricant if it’s rusted or stuck. Now it’s time to remove the axle nut. In some cases, this step may require quite a bit of effort. If this is the case, your safety bet is to do this step before jacking the car up. This is where the optional impact wrench will come in handy.

Can a CV axle cause damage?

A: Yes, since it’s connected directly to the transmission, a failing CV axle can cause damage. Excessive movement from a damaged axle can wear components inside the transmission more quickly than they would normally.

Can you ignore a bad CV axle?

A: No. Do not ignore a bad CV axle. The vibrations you’re feeling and noise you’re hearing are a warning that it’s time for maintenance. If your axle fails while you’re driving, you could lose control of your car.

Can you shorten the life of a CV axle?

Driving over rough terrain where there are rocks and debris can shorten the life of a CV axle, because there are more opportunities to damage the rubber boot that protects the moving parts. The same goes for driving in snowy or icy conditions, where salt and sand can also damage the rubber.

How much does it cost to replace CV joints?

Replacing a CV joint will most probably cost the same as replacing the axle shaft, but the overall cost will depend on whether or not you’re replacing one or both components. You can buy a new axle shaft for 86 to $200, whereas parts and labor combined can cost anything from $150 to $750. A double-axle joint replacement job can cost twice as much ...

What does it mean when your CV axle is broken?

Other broken CV axle symptoms include a car that vibrates every time you accelerate, which could be a sign of damage either on the CV joint or even the driveshaft, depending on the design of your car. While CV joint malfunction can manifest in steering problems, this is mostly caused by issues with the driveshaft.

Why does the axle shaft fail?

That’s why one end of the axle shaft is attached to the transmission while the other end is attached to the tires. The transmission works to gently spin the shafts so that they can be able to turn the wheels in order for the car to move. Leaking grease is one of the primary causes of axle shaft failure. As the grease leaks out, it leaves the CV ...

What is CV joint?

The CV joint is a key component of the actual axle shaft and sits next to the boot and the grease. The axle shaft is commonly referred to as a ‘CV axle’ or a ‘half-shaft’, and its job is to link the tires of your car to the gears in the transmission. That’s why one end of the axle shaft is attached to the transmission while ...

What happens if grease leaks out of CV joint?

As the grease leaks out, it leaves the CV joint dehydrated, and a lack of lubrication will lead to dirt and debris getting into the joint, which will accelerate wear and tear even more. Most mechanics you consult when you have this problem will most likely recommend that you replace the entire half shaft instead of the separate parts.

What causes CV joints to malfunction?

The function of the CV joint in your car is to connect the tires to the gears, and the main things that cause it to malfunction are prolonged wear and tear and a lubrication deficiency. A lack of lubrication is not only one of the main causes of CV joint malfunction but it usually signals a potential leak from the boot, ...

What is shaft replacement?

Axle shaft replacement is one of those jobs that you want to leave to a professional, even if you’re experienced when it comes to replacing car parts because it’s such an important part of your car’s function that you don’t want to make any rookie mistakes on it and compromise your safety while driving.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9