
Fixing a quarter panel will likely cost around $2,000, unfortunately. Body panel repairs, including quarter panel repairs, are usually expensive. If the damage is extensive enough that the panel needs to be replaced, a new corner panel can cost anywhere between $500 and $1500, depending on if you use aftermarket parts or OEM.
How much does it cost to fix a quarter panel?
Similarly, it is asked, how much does a quarter panel repair cost? The only other factor that you'll probably consider when getting a replacement quarter panel would be the price. Smaller panels can go for as low as $50, while larger ones can range anywhere from $100 to $1000.
How long does it take to replace a quarter panel?
What sparked this thread was the fact that the non certified shop made it seem like it would only take three days or so to replace the quarter panel once they had the parts whereas the certified shop is telling me three weeks. It seemed excessive, but I guess it's par for the course.
How do you replace a quarter panel?
- Vinyl roof access – If the vehicle has a vinyl roof, you should charge extra for the time required to partially or fully remove the vinyl top. ...
- Corrosion protection – Metals should be properly treated to protect them from corrosion. ...
- Broken glass cleanup – Who vacuums up any broken glass in the vehicle? ...
How to replace rear quarter panel?
hold the new quarter up to the car, trace around it. use the cut off wheel to cut out the panel on the line you drew. Have a friend hold the new panel up while you run the duct tape all the way around. rattle can the panel to match the car. better yet, rattle can the whole car flat black.

Can a rear quarter panel be replaced?
On the surface, it's a simple job: cut the old quarter-panel off and weld a new one on. Like all things in life, however, it's not quite so easy. Because you're welding the new panel on, undoing a poorly done install can be a major pain in the butt.
Is it better to repair or replace a quarter panel?
No matter what a body shop tells you, there is never an acceptable time for the your car's damaged quarter panel should be replaced with a previously used “aftermarket” quarter panel.
Why is a quarter panel so expensive?
The reason for this is the quarter panel is much more expensive and labor-intensive to remove and replace. Replacing a welded-on quarter panel disturbs more of the original construction, such as seams, welds and corrosion protection, so more repair time can be allocated before the replacement threshold is met.
Is a quarter panel fixable?
Olson said any holes drilled in a used quarter panel might be 10 mm, perhaps 10.5 after deburring. As the OEM wants only 8 mm plug welds, it's officially impossible to deliver the repair with a used quarter panel, according to Olson.
How many hours does it take to replace a quarter panel?
See all 21 photos Before the new Goodmark panels can go on, the old ones need to come off....We Show You How To Replace A Rear Quarter-Panel With New Parts From Goodmark Industries.LABORReplace left 1/4 panel16 hoursReplace rear panel8 hoursFit trunk1.5 hoursTotal labor28.5 hours10 more rows•Apr 10, 2008
Is rear quarter panel structural?
Even though a quarter panel is not considered a structural component with regards to the vehicle structure, they do interact with the structural components.
How much does it cost to replace a 1/4 panel?
Fixing a quarter panel will likely cost around $2,000, unfortunately. Body panel repairs, including quarter panel repairs, are usually expensive.
How much does it cost to replace a quarter panel?
The cost of a quarter panel replacement ranges from $20 for a small part of the quarter panel up to more than $1500 for a larger quarter panel. Other factors that affect the cost of quarter panel replacements include the quantity sold, the location of the panel, and the exact model of your vehicle.
How do you fix quarter panel damage?
4:5512:57How I Fixed My Smashed in Quarter Panel - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I can cut it up and then drill holes in it which again doesn't really make any sense that you'reMoreSo I can cut it up and then drill holes in it which again doesn't really make any sense that you're swapping in a good piece just to make it.
How do you fix a dent in a rear quarter panel?
Bring a pot of water to a boil and take it out to your vehicle. Slowly pour the hot water over the dent so it heats up the panel and makes it more malleable. After that, spray the area with compressed air to cool it down quickly. If you're lucky, the dent will pop right out.
How much does it cost to replace a side panel?
It can cost over $2,000 to replace a truck side bed panel. The panel itself usually runs between $800 and $1,000 and there are additional labor fees to remove the bed and install the new panel.
How many quarter panels does a car have?
two quarter panelsQuarter Panel Location Your car has two quarter panels, both of which are located at the rear of your vehicle. Your car's rear quarter panels can be found right between your rear door and the trunk or bed (depending on whether you have a standard car or a truck).
How much does it cost to replace a quarter panel?
Fixing a quarter panel will likely cost around $2,000, unfortunately. Body panel repairs, including quarter panel repairs, are usually expensive.
Is quarter panel frame damage?
While you may be able to drive a car with frame damage, that doesn't mean it's a good idea. If it's something small, like a dented rear quarter panel, then sure, you should be fine. But if the structural integrity of your car has been compromised, driving it could be extremely dangerous.
What is a quarter panel assembly?
A quarter panel (British English: rear wing) is the body panel (exterior surface) of an automobile between a rear door (or only door on each side for two-door models) and the trunk (boot) and typically wraps around the wheel well.
What is a hem flange quarter panel?
These quarter panels are attached the same way that a door skin is attached to the door shell; which means that for removal, the edge of the hem flange is ground off. Rolled hem flanges cannot be straightened to release the inner panel, in order to reuse the outer quarter panel.
How long does it take to replace a quarter panel?
Depending on the vehicle it could take a week. Depending on the amount of damage, most shops would simply cut out the damaged area, cut the new quarter panel in the same shape and would weld it on. If it is bad enough however, the whole thing will need to be replaced.
What is a quarter panel?
The quarter panel is typically glued AND welded to the body. Any spot weld will need to be drilled out and the glue needs to be cut and scraped off. Then it needs to be bent and pried off. The new one need to be welded and glued on. The new one needs to be sanded, cleaned, primed and painted.
Can an appraiser ask for a body shop?
Alternatively, the appraiser may ask the body shop to source the parts prices for them (which allows the shop to deal with their preferred suppliers.
What happens when you disassemble a wrecked car?
When you disassemble a wrecked vehicle, the damage makes access to fasteners more difficult, so a quick pull or two may be required. Whether or not bent parts prohibit access to fasteners, vehicles may need to be anchored and pulled back to a roughly similar shape to the original OEM design.
Can you remove a quarter panel from a donor vehicle?
Although there are situations when I actually do prefer a used assembly, quarter-panel replacement isn’t one of those situations. It’s not easy to remove a used quarter panel from the donor vehicle without damaging the panel. While it can be done, it’s a tedious and time-consuming task.
Is drill labor included in quarter panel replacement?
Drill labor – Not included in quarter panel replacement by any of the top three information providers, drill labor is additional labor. You should charge for the time necessary to drill spot welds when removing the damaged quarter and to drill holes on the replacement part for plug welds.
Do you have to blend quarter panels?
Advertisement. When painting a quarter panel, you may have to blend the roof if there’s no break between the roof and quarters. Paint manufacturers recommend against solvent blends because they aren’t permanent and can often be easily detected.
Can you charge extra for removing a vinyl roof?
Vinyl roof access – If the vehicle has a vinyl roof, you should charge extra for the time required to partially or fully remove the vinyl top. This isn’t to be confused with a convertible top, the removal of which I believe is generally included in the labor to replace a quarter panel on a convertible.
Is the time required to test fit and align parts included in the quarter panel replacement labor?
Since the recommended labor times are for the replacement of new, undamaged panels on new, undamaged vehicles, I’d say the time required to test fit and align parts isn’t included in the quarter panel replacement labor.