DIY Bicycle Repair Stand
- Parts and Tools. The materials and tools necessary to build this repair stand are readily available, easy to work with, and best of all, pretty inexpensive.
- Building the Base - Step 1. We begin by grabbing the tee fitting and two (2) of the ten (10) inch lengths of pipe. ...
- Building the Base - Step 2. There's your completed stand! Just kidding. That'd be lame. That would also mean each piece cost about ten dollars.
- Build the Base - Step 3. It's time to put the base components together. Obtain the piece from Build the Base - Step 1. ...
- Up We Go! - Install the Vertical Pole. What's that extra port on the tee, you ask? That's for the big 60" length of pipe. ...
- Ummm...Add the Other Thing! We will now add the arm that will hold the clamp that will hold the bike. ...
- Clamp the Clamp. Grab your two hose clamps and the spring clamp. ...
- Voila! Throw Your Bike Up There! If you are certain all joints that have rotational stress on them are tight (this would include the lower tee and two ...
- Improvements. As with any project, this is version 1.0. There are some improvements that could definitely do some good.
Full Answer
What is the best bicycle repair stand?
The Bike Repair Stand
- Bikehand Pro Mechanic Bicycle Bike Repair Rack Stand. The Bikehand Pro Mechanic Bicycle is our top pick and the best choice of bicycle repair stand. ...
- Sportneer Bike Repair Stand. The Sportneer Foldable Bike Repair Workstand is the perfect and dependable companion for all bike enthusiasts.
- Feedback Sports Sport Mechanic Bike Repair Stand. ...
How to make a bike repair stand DIY?
Step 1 – Position the flange near a corner of the plywood square, one inch from each edge. With a pencil, mark the four holes. Step 2 – With the 1/4″ bit, drill two of the holes for the flange. Temporarily insert two of the bolts and the flange. This will allow you to accurately drill the other two holes. Step 3 – Assemble the pipes and fittings.
How to use a bicycle repair stand?
What Do You Use a Bike Stand For Anyway?
- A Lesson On Wheel Truing Using – A Bike Repair Stand. Bicycle wheels need truing from time to time – simply from constant use, or following a bike crash. ...
- Another Lesson On Wheel Truing – But Using A Truing Wheel Stand. In this video, Daniel Lloyd explains how to straighten your wheels using a Truing Wheel. ...
- Building A Bicycle Using A Bike Stand. ...
What is the best bicycle repair kit?
The Best Bike Repair Kit
- Lumintrail Bike Repair Tool Kit. This entry-level bike repair kit comes with 42 commonly used tools and is ideal for most maintenance and repair jobs.
- Crank Brothers Bicycle Tool. ...
- Park Tool AK-3 Advanced Mechanic Tool Kit. ...
- BIKEHAND Bicycle Repair Tool Kit. ...
- Aim High Pro Bike Repair Kit with Pump. ...
- Bicycle Repair Bag & Bicycle Tire Pump. ...
How do you make a homemade bike repair stand?
1:144:11How To Build Your Own Bike Work Stand in Just 30 Minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to take our long pipe and screw the connecting elbow to one end so it looks a littleMoreWe're going to take our long pipe and screw the connecting elbow to one end so it looks a little something like this. Next we'll take the 12 inch pipe and screw it into the other end of the elbow.
How do you make a wood bike repair stand?
6:4711:27DIY Bike Repair Stand made out of wood - One 2x4 and one 4x4YouTubeStart of suggested clipEnd of suggested clipEnough now put some boards across here. I cut two 14 piece or 14 inch pieces. Too by far. So gotMoreEnough now put some boards across here. I cut two 14 piece or 14 inch pieces. Too by far. So got this whole thing up susana put two boards which are gonna just hold the seat.
What can I use as a bike repair stand?
9:1711:12How to use a bicycle repair stand and what features to look for - YouTubeYouTubeStart of suggested clipEnd of suggested clipI like to do it with the bike on the ground. And then just take an old toe strap or a velcro strapMoreI like to do it with the bike on the ground. And then just take an old toe strap or a velcro strap or something and tie the back wheel and tire assembly to the side of the repair.
How do you make a 2x4 bike stand?
0:257:09How to Build a Wood Bike Stand! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd basically I'm gonna take my two 16-inch blocks. And place something on each side of the tire.MoreAnd basically I'm gonna take my two 16-inch blocks. And place something on each side of the tire. Now what you want to do is give enough room so that's the tire sitting flat.
How do you make a bike stand?
0:003:39How To Make A Bike Repair Stand DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's one quarter inch and it is screwed to the base. With nuts on the backside which your counterMoreIt's one quarter inch and it is screwed to the base. With nuts on the backside which your counter sunk into the wood. This is what the bolts look like on the bottom side for the hold the flame.
How do you make a wooden bike rack?
0:122:21How To Make A D.I.Y. Bike Rack - D.I.Y. At Bunnings - YouTubeYouTubeStart of suggested clipEnd of suggested clipDown your timber nice and tight cut off your taper on both ends. And continue on for all six pieces.MoreDown your timber nice and tight cut off your taper on both ends. And continue on for all six pieces. Remove any of the burrs or rough edges giving it a light sand.
How do you make a PVC bike Stand?
0:267:36DIY PVC Bike Rack - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-footMoreYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-foot sections. Although I asked an employee at the hardware store to cut mine in half.
What makes a good bike stand?
Angle adjustment: the ability to change the angle of the clamp is crucial when doing more complex repairs such as bleeding hydraulic brakes. The ideal is a stand that's adjustable, easy to swivel and locks down rigid when wanted – it's a pain when you're trying to do something precise and the whole bike tilts away.
Is it worth getting a bike repair stand?
You don't absolutely need a bike repair stand to take care of the most basic maintenance—lubing your chain, swapping tires—but once you start adjusting your own derailleurs or messing around with cables, having a way to adjust your bike while its wheels are off the ground is crucial.
How do you make a free standing bike rack?
0:418:07How To Make A DIY Bike Rack | Hank Builds A Freestanding Bicycle RackYouTubeStart of suggested clipEnd of suggested clipFirst off you can get them for any wood supplier first off make your frame. Then you need to make aMoreFirst off you can get them for any wood supplier first off make your frame. Then you need to make a second frame. So I brought that good a joint. Sits there and then you need to build your braces.
How do you make a wooden stand?
0:265:02DIY Tool Stand made from 2x4s | Evening Woodworker - YouTubeYouTubeStart of suggested clipEnd of suggested clipI first cut all of my two by fours to length with the miter. Saw. I then cut off the rounded cornersMoreI first cut all of my two by fours to length with the miter. Saw. I then cut off the rounded corners on all of them with a table saw this step isn't necessary.
How do you build a vertical bike rack?
9:0217:38Vertical Bike Rack Build - Step by Step Guide with Measurements - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i cut just a bunch of these into equal lengths tied a simple knot at the end. And then you canMoreAnd i cut just a bunch of these into equal lengths tied a simple knot at the end. And then you can hook it around the bar. Just like that you go over your wheel.
How do you make a homemade mountain bike stand?
0:029:01How to Make a Simple Wooden Bicycle Mountain Bike StandYouTubeStart of suggested clipEnd of suggested clipStraight keep it all in line. So that in the end I went for 14 inches for the bottom pieces. And 20MoreStraight keep it all in line. So that in the end I went for 14 inches for the bottom pieces. And 20 inches for the top two pieces and that will depend on the size of your wheel I have a 26 inch wheel.
How do you make a PVC bike Stand?
0:267:36DIY PVC Bike Rack - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-footMoreYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-foot sections. Although I asked an employee at the hardware store to cut mine in half.
How do you use a mountain bike without a stand?
Just hang the front of the seat on any convenient "peg", or rig hooks or a rope to suspend the bike from. All you need to do is somehow get the rear wheel off the ground while having the pedals clear to turn.
What is MTB stand for?
mountain bikeThe acronym MTB stands for mountain bike and derives solely from mountain bike.
DIY Bike Repair Stand – The PVC Option
As usual, Instructables has some nicely designed bike repair stands. This one is a really sweet-looking bench-mounted repair stand, made of PVC.
The Alternate PVC Bike Repair Stand Option
Here’s the second design from Instructables. It’s a free-standing PVC bike repair stand. This is a pretty clever design that uses no clamp to hold the bike in place.
The Wooden Bench Mounted Repair Stand
This wooden bench-mounted repair stand looks like a straightforward build. You’ll need a workbench and some pipe clamps. This one uses a bit of plumbing polyurethane in place of the foam pipe insulation of the previous builds.
The Pipe Based Option
This fine-looking pipe-based bike repair stand uses simple and easily obtainable raw materials. The clamp looks a little overbuilt, though I bet you could use one of the PVC clamps from above without much ill effect.
The Wood Based Stand
This is a really simple design for another bench-mounted bike repair stand and might be just the thing if you’ve got a workbench. The site has nice plans for the build.
Freestanding Wooden Repair Stand
This next one is pretty interesting. I found a reference to it in various search engines, but the site was gone. Wayback Machine to the rescue!
Step 1: Materials and Tools
10' length of 1 1/2" EMT (electrical metallic tubing) - $12.45 from Home Depot electrical dept.
Step 2: Clamping Mechanism
The clamping mechanism consists of modified locking pliers welded to the 1" steel pipe section. Steel pipe was selected due to its stiffness.
Step 3: Rotating Clamp Mechanism Support
The support for the clamp mechanism allows the clamp to rotate 360 deg. The 1" steel clamp pipe fits loosely into the 1 1/4" EMT. I cut a 4" length of 1 1/4" EMT to hold the clamp pipe. I cut a slot down the length of the 4" long EMT with a cut-of blade in the angle grinder and then made the slot a little wider.
Step 4: Base Stand
The base stand is made of 1 1/2" EMT. I cut a length about 4' long for the base post. and drilled (5) 3/8" holes about 3" apart near the top of the post. The holes allow for height adjustment of the clamp support post. I then cut two other pieces about 30" long for legs. The two legs project to the front at about 45 degrees on each side.
Step 5: Ready for Paint
I ran into some issues during painting due to cold, humid weather, so am posting the almost finished pictures for now. As you can see in the photos, the repair stand works for holding the bike by the top tube as well as by the seat tube.
Step 6: Final
Painted the whole thing blue. After paint I added the 3M heavy-duty double sided tape to each side of the clamp angles and adhered the rubber pads. I cut the pads so that they slightly overhang each edge of the angles. You can see how the placement of the T-handle bolts and the addition of the 1" steel spacer help the handles from interfering with each other and the side of the clamp support. All done.
Step 1: Side Note: About This Bike
This bike is a 1973 Motobecane Le Champion that I've been holding onto for several years, intending to get it back on the road at some point.
Step 2: A Closer Look
Here is a look at all of the completed components that make up my bike repair stand clamp apparatus thing.
Step 3: It's Like Playing With LEGO
A similarly functioning apparatus could be made in any number of ways, depending on what things a person has to work with.
Step 5: Finish Clamp Arms
The clamp arms were cleaned with a wire wheel in a power drill to remove all the paint and rust.
Step 7: Modify Carriage Bolt
In order for the carriage bolt to pivot as needed, I trimmed off one side of the head as shown using an angle grinder.
Step 8: Add Pads
Some scrap pieces of rubber from a floor mat were cut to size as needed.
Step 9: Support Arm
The support arm that holds the clamp was made from a piece of 1 3/4" by 1/4" thick angle iron, a scrap piece of metal tubing, and a pair of washers.
How to Build a DIY Bicycle Repair Stand
You can build your own DIY bicycle repair stand with, a few lengths of gal pipe, and some t-piece and right angle joiners from the local hardware store. It’s pretty easy to make your own repair stand for carrying out bicycle maintenance.
Materials To Build Your – DIY Bicycle Repair Stand
This DIY Bike Repair Stand is probably the easiest we’ve come across. The items you’ll need to buy (or acquire) are …
How long to let a X-ray machine sit?
Hold the parts together for at least 30 seconds more. Then let the cemented assembly sit for at least 2 hours. After at least 2 hours, you will lay the X down on the work surface & sprinkle some of the PVC shavings into the gap in the crotch of the X on one side. Then dribble a small amount of cement into the shavings.
What tools are needed to cut PVC pipe?
There is also some shaping of some of the pipe & fittings, so some carving & shaping tools are required. Tools: - hack saw ( or alternately a P VC tubing cutter) - tape measure. - wood chisel (or alternately a dremel tool with a carbide bit) - pencil & dry-erase marker. - file. - sand paper.
Can you use a level on a stand?
You can use a level to make sure (as long as you are sure you are working on a flat level surface). Once you are satisfied that the stand is perfectly upright & the base is stable with no rocking, you should put alignment marks in the upright portion of the T-fittings & the 34" legs near the T-fittings.
Can you dribble cement into a fitting?
You can also coat the other parts of the cemented joint with another coat of cement to make sure it is strong. Just be certain not to dribble cement into the branches of the fitting that will later need to have pipe inserted. Now you're done with the most tedious & time-consuming part of the build.
