- Unplug and Clean. Compare water dispensers on Amazon. Always unplug your water cooler dispenser before doing any repair or maintenance on it.
- Reset the Water Cooler. Drain any remaining water and wipe dry. Plug your cooler back into the wall outlet, but do not replace the jug just yet.
- Make Replacements. If any parts such as coils or spouts need to be replaced, try to obtain new ones for your specific brand and model from the ...
How do you fix a moldy swamp cooler?
Remove mold by using a combination of water, vinegar, and bicarbonate of soda, and scrub away at the inside of the machine. In the future, it is a good idea to learn how to properly winterize your swamp cooler, as this will prevent some repairs from being necessary in the summer.
How do you remove the plastic from a cooler?
Grab your screwdriver and just take everything off of your cooler (Hinges, latch, handles, etc.). Then, remove the plastic inserts by just pulling them out and also take any insulation (styrofoam) out at the same time. Also, if your cooler has a drain somewhere, remove that as well.
What should I do if my water cooler fan is not working?
Remove the fan from the cooler, and examine the condition of the fan paddles. If they are damaged or corroded, discard the fan and start again. Look at the motor and belt which drives the fan. Fitting a new belt can be easily done, but bad motors probably need a complete replacement. Check the fan is working correctly before reinstalling.
How do you Guys store your cooler?
Also, if your cooler has a drain somewhere, remove that as well. It's a good idea to put all of the hardware in ziploc bags or containers and set them aside somewhere so you don't lose them.
What to do if cooler is not cooling?
0:001:06Air Cooler | Room Is Not Cooling Properly - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell this might happen if the water tank is empty or it is out of ice cubes all you have to do isMoreWell this might happen if the water tank is empty or it is out of ice cubes all you have to do is switch on the pump add adequate water in the tank through the water inlet using a mug or a drain pipe.
Can an air cooler be repaired?
Most of the time, we'll advise you to proceed with fixes such as new fan motor, repainting or change of cooling pads. However, If your system is older and needs extensive repairs, we'll advise you to replace it instead. The bottom line is that whether you replace or repair your air cooler is completely up to you.
Why is my cooler not working?
Water cooler troubleshooting Very often if your water cooler is not working, the problem can be traced to the power supply. So as a first step, check that it is properly plugged in at the wall and the mains power is turned on. If it is switched on but not dispensing water, the next step is to check your water supply.
Why my cooler pump is not working?
Your problem may be a lack of water, rather than a broken pump. Check to see that the pump is getting power. Some pumps plug directly into a standard electrical outlet, and some are wired inside of a box in the cooler. If the pump is not getting power, check the circuit breaker or the ground fault circuit interrupter.
Which cooler motor is best?
Nimble Cooler motor is best for your cooler. It comes with 100% Fresh copper and in cell cover which is best for motor. Its compatible with all cooler. This motor can runs normally on Inverter also, its with Double ball bearing, its is of 105 watts with 1400 rpm high speed.
What is the price of air cooler?
Air Coolers Price ListS.noProducts - Air CoolersPrice2Kelvinator Personal Cooler - 42 Litres KCP-B420, Remote...₹6,490.003Kelvinator Alps KCT-A300 - 30 Litres Tower Air Cooler₹4,990.004Kelvinator Personal Cooler - 22 Litres KCP-B220, 4 Way ...₹3,990.005Kelvinator Desert Cooler - 70 Litres KCD-B700, 4 Way Ai...₹8,290.007 more rows
Which capacitor is used in cooler?
STAR SUNLITE Plastic 2.5 MFD Capacitor for Ceiling Fan and Mini C......BrandSTAR SUNLITEMinimum Operating Temperature27 degCCapacitance4 MFDMaterialPlastic FilmOther Features2 pcs set 4 mfd Capacitor Match mfd & buy Capacitor for desert cooler fan motor4 more rows
How do I test my air cooler?
How it WorksRemove turbo hoses and clamps.Install Tester-Kit plugs and clamps. Mount gauge and double check system.Apply 30 psig of air. Remove air supply and check gauge. See chart (below) for Leak Down Rate Specifications. ... Release air. Test is now complete.
How do I fix my water cooler not cooling?
This is very easy to do: First, remove a few cups of water from your machine, then completely unplug your water cooler from the mains. We then suggest leaving your machine for 24 hours before switching it on again. After 24 hours, plug it back in and wait 6 hours for the water to adjust to a cooler temperature.
Which motor is used in cooler?
air cooler consists of two motors one is air blower motor it a an capacitor start run induction motor and the other motor is for circulating water around the grills this motor is a shaded pole induction motor .
Which pump is used in cooler?
windstar Cooler Pump Water Lifting Submersible Pump | For Desert ......BrandZOLTAModel NameKhaitan Submersible Pump for Desert Air Cooler, Aquarium, Fountains, 18W, 1.6 m, For Cooler And FountainTypeSubmersibleUsage TypeDomestic8 more rows
Can water pump be repaired?
Fixing a water pump refers to the process of replacing an essential part of your vehicle's cooling system. It is one of the least complicated procedures to carry out, as far as auto repairs go, so almost anyone who can operate a wrench can do this on their own.
How many years does an air cooler last?
A good fan should last 5-6 years without incident, the cooler should last hundreds.
What are common problems with air conditioners?
Read over some common air conditioner problems to get your air conditioner running in excellent condition.Water Leak (Inside the House)Water Leak (Outside the House)AC Refrigerant Leak.Dirty Air Filter.Damaged Compressor.Frozen Evaporator Coil.Capacitor Failure.Thermostat Malfunctioning.More items...•
How do I fix my water cooler?
Perform a reset on your cooler if it is freezing the water or if it is not getting cold enough. To do a reset, drain a few cups of water out of both the hot and cold sides of the water cooler. Then turn the switches in the back of the cooler off. Unplug your water cooler, and leave it unplugged for 24 hours.
What are the causes of air conditioner problems?
Top 7 causes of air conditioner problems:Low refrigerant. ... Frozen evaporator coils. ... Dirty condenser coils. ... Fan problems. ... Leaking ducts. ... Thermostat problems. ... Clogged drains. ... Replace dirty air filters.More items...•
How to replace a fan on a spherical cylinder?
1. Adjust the phase#N#2. Check whether the motor is damaged, whether the fixing hoop and the fan seat are deformed#N#3. Replace the main magnet#N#4. Clean or replace the water curtain or dust net#N#5. Replace the fan#N#6. Replace the main board.
What is swamp cooler?
The environmental protection swamp cooler is a kind of ventilation and prevention combination unit for dust clean, cooling, and deodorization purposes. Although there could be many reasons causing a problem, there are a number of general troubleshooting steps that you can follow to get the Swamp Cooler working again.
How to reset a power supply?
Restore power supply, check the power supply circuit#N#2. Replace the signal line or adjust the circuit#N#3. Replace the main control board#N#4. Close the air switch or replace the fuse#N#5. Replace the panel.
Why do swamp coolers need to be repaired?
Another common need for swamp cooler repairs is caused by the fan breaking down. This may be caused by a number of factors. Remove the fan from the cooler, and examine the condition of the fan paddles. If they are damaged or corroded, discard the fan and start again. Look at the motor and belt which drives the fan.
What to do if swamp cooler pads are worn?
If the pads on your cooler are worn, replace them for a new set before using the swamp cooler.You should then check the float valve. Water may be impeded from flowing into the reservoir by a broken valve, and this can cause leaks. Replace the valve is necessary.
How to get swamp cooler out of retirement?
Once you get your swamp cooler out of retirement, you will need to perform a quick check of the machine. Plug it into a safe socket (which has a circuit breaker device installed), and then operate it for a full cycle.
What is swamp cooler?
The swamp cooler is a water-based device that cools the air by increasing the humidity. There are many complex parts to a swamp cooler, including the water reservoir, the air pumps, the electrical connections, and then fan. A lot of these items can become broken just by sitting in storage during the winter, so you will need to practice ...
How to get mold off a washing machine?
Remove mold by using a combination of water, vinegar, and bicarbonate of soda, and scrub away at the inside of the machine.
How to get paint off a cooler?
Get out your gloves, paint stripper and a paint brush. Put on your rubber gloves and liberally brush on the paint stripper to any areas with paint on them and wait until all of the paint starts to bubble. Then get your scraper and start scraping all of the paint off. Most of it should come off pretty easily, but you may have to use some steel wool to get any stubborn areas clean. After all of your paint is off, rinse the cooler off with water and dry it with an old towel or t-shirt.
How to remove plastic inserts from a cooler?
Grab your screwdriver and just take everything off of your cooler (Hinges, latch, handles, etc.). Then, remove the plastic inserts by just pulling them out and also take any insulation (styrofoam) out at the same time . Also, if your cooler has a drain somewhere, remove that as well.
How to apply cream filler?
To apply your filler, mix it with the cream hardener that it comes with and then use a putty knife or a special spreader to put on a smooth, even coat. After it cures, you'll need to sand it down. I used a power sander with some 80 grit sandpaper. After you've sanded it, you'll need to prime it again. Ask Question.
How to get rid of rust on a sandblaster?
If you have access to a sandblaster, that is the most effective way. Otherwise, you can use an angle grinder, sandpaper and a wire brush, or acids. I chose to use some acid since There was just some light surface rust on mine.
How to get rid of rust on a steel cooler?
For smaller ones, use the small pointed end. You can get rid of the rust in several ways. If you have access to a sandblaster, that is the most effective way.
Can you spray primer on a cooler?
Once you're satisfied with your dent and rust removal, you can spray a coat of primer on your cooler. I used some thick sandable primer, since I needed to add some body filler to a few areas to get rid of some minor imperfections afterwards.
