- 1 Shut Off the Water and Flush the Toilet. Once you've flushed the toilet and emptied the tank, go underneath the tank...
- 2 Align the New Ballcock Valve. Align the float arm socket in float arm will pass behind the overflow pipe. Screw the...
- 3 Attach Refill Tube. Bend or clip the refill tube so that the tip is inside the overflow pipe.
Full Answer
Do I need to replace the ballcock on my toilet?
Many older toilets have ballcock fill valves that will eventually need replacing due to use and wear. If your toilet runs constantly, makes odd humming or groaning sounds or the handle feels light when you press down on it and the toilet won’t flush, you may need to replace your toilet’s ballcock assembly valve.
How to replace a ballcock tailpiece?
Attach a new cone washer to the new ballcock tailpiece and insert the tailpiece into the tank opening Align the float arm socket in float arm will pass behind the overflow pipe. Screw the float ball onto the float arm.
How do I change the ballcock on my Kenmore washer?
1 Shut Off the Water and Flush the Toilet. Once you've flushed the toilet and emptied the tank, go underneath the tank and place a bucket under the retaining nut. Now remove the ballcock retaining nut with an adjustable wrench and take out the old ballcock assembly. 2. Align the New Ballcock Valve. Attach a new cone washer to ...
How do you attach a float to a ballcock?
Screw the float ball onto the float arm. Bend or clip the refill tube so that the tip is inside the overflow pipe. Screw the mounting nut and the supply-line coupling nut onto the ballcock tailpiece and tighten it with an adjustable wrench.
How do you install a ballcock kit?
0:121:39How to Install and Fix a Ballcock Valve | Toilet Repair | The Home DepotYouTubeStart of suggested clipEnd of suggested clipThen insert it into the tanks opening. Now align the float arm socket. So that the arm will passMoreThen insert it into the tanks opening. Now align the float arm socket. So that the arm will pass behind the overflow pipe and screw the float ball into place next bend or cut the refill tube.
How do I put a new ballcock in my water tank?
How to Fit a Ball Valve in Your Cold Water TankTurn Off Water. To start, turn off the water at the mains.Unscrew Feed pipe. ... Detach Feed Pipe. ... Undo Retaining Nut. ... Insert New Ball Valve. ... Reattach Feed Pipe. ... Check for Leaks.
How do you fix a leaking ballcock?
0:347:55Overflow running? How to repair a part 2 brass ballcock, ball valve ...YouTubeStart of suggested clipEnd of suggested clipAnd it's pretty easy to do this is taken out of a roof tank normally. That would be the back nutMoreAnd it's pretty easy to do this is taken out of a roof tank normally. That would be the back nut securing. The roof tank there and that would be screwed on so you don't do your water connection.
What does a ballcock valve look like?
It consists of a valve connected to a hollow, sealed float by means of a lever mounted near the top of the tank. The float is often ball-shaped, hence the name ballcock. The valve is connected to the incoming water supply, and is opened and closed by the lever which has the float mounted on the end.
Can I replace a ballcock fill valve?
You can replace a ballcock fill valve without calling a professional toilet repair service for help.
How do you change a ball valve washer?
2:5215:18Fix dripping sound in water cylinder: Float valve washer change walk ...YouTubeStart of suggested clipEnd of suggested clipSo just use some pliers to bend. It back pretty straight. And that should pull straight through theMoreSo just use some pliers to bend. It back pretty straight. And that should pull straight through the original gap there we go straight out.
How do I stop my overflow from dripping?
There are several possible fixes for this:Check the float valve isn't stuck (as described in step 2 above). ... Adjust the position of the float. ... Check the water feed pressure. ... Replace the washer in the float valve. ... Replace the float valve.
How do you fix a ball valve?
0:020:44How to Fix a Leaky Water Valve (Ball Valve) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe handle for the ball valve then underneath there's another nut use a 12 millimeter wrench or halfMoreThe handle for the ball valve then underneath there's another nut use a 12 millimeter wrench or half inch wrench to tighten it clockwise. All it takes is a little bit once it's tight the leak should.
How does a ballcock fill valve work?
A ballcock works through using a float with an arm attached that sits on top of the water. As the float rises, the arm pivots round a pin and opens and closes a valve. As the float rises, the valve closes until the required water level is reached and, at this point, the flow is completely shut off.
How do you adjust a ballcock valve?
1:273:34How to adjust the cistern ballcock in your WC cistern, get a better flush.YouTubeStart of suggested clipEnd of suggested clipIf you want it to be less water when it ain't your turn it clockwise. So that ends up turning offMoreIf you want it to be less water when it ain't your turn it clockwise. So that ends up turning off earlier. If you want more watering which is probably what you're after.
How do you turn off water to toilet without valve?
Some older toilets don't have shutoff valves behind them. If this is the case for you, you'll have to use the wooden board method or simply cut off the main water supply for your entire home to turn off the toilet's water supply.
What causes the water level in the toilet bowl to drop?
In the case of your toilet water levels, when pressure shifts within the pipe system, the water in the toilet bowl is consequently affected. With a decrease in pressure within the pipes, there is a suction effect. The toilet water is pulled to this area of low pressure, and as a result, water levels drop.
What's the difference between a Part 1 and Part 2 ball valve?
Part 1 and Part 2 ball valves – the main differences On a Part 1 or 'Portsmouth' valve, the outlet is on the underside of the valve. However, on a Part 2 or 'diaphragm' valve, the outlet is on the top. Water is directed down into the cistern via a small plastic spout which screws onto the valve body.
How do I stop my water tank from overflowing?
It's normal for the overflow pipe on a copper cylinder to drip when your water is heating. But if you find it's running with water, causing your tank to overflow, then your water could be getting too hot. To fix this, simply adjust the temperature on your thermostat down a little.
How do I stop my overflow pipe from leaking?
Adjust the position of the float as it might be set too high to turn the water off. Check the water supply pressure isn't too high causing the overflow pipe to leak. Lower it by turning the isolation valve on the water supply pipe. Replace the washer in the float valve.
How do you remove a ball valve?
1:146:53How to replace ball valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the remove that you just put in this handy-dandy. Little tool that comes with his replacementMoreAnd the remove that you just put in this handy-dandy. Little tool that comes with his replacement plug get a ratchet that goes in there. And you remove that old plug.
Shut Off the Water and Flush the Toilet
Once you've flushed the toilet and emptied the tank, go underneath the tank and place a bucket under the retaining nut. Now remove the ballcock retaining nut with an adjustable wrench and take out the old ballcock assembly.
Align the New Ballcock Valve
Attach a new cone washer to the new ballcock tailpiece and insert the tailpiece into the tank opening
Attach Refill Tube
Bend or clip the refill tube so that the tip is inside the overflow pipe.
Attach Supply Line and Turn On Water
Screw the mounting nut and the supply-line coupling nut onto the ballcock tailpiece and tighten it with an adjustable wrench.
Adjust the Water Level in the Tank
The water level in the tank should be about 1/2 inch below the top of the overflow pipe, or align with the marked "full" line inside the tank.
