Here are the steps:
- Secure the tools needed for the installation, including a pipe wrench, pair of pliers, bucket, sponge, pair of scissors, a bucket and a hand saw.
- Familiarize yourself with the repair kit’s contents, check out the instructions sheet and then assemble the necessary hand tools. ...
- Turn the toilet’s water supply off. ...
How to install a new toilet correctly?
- Since there are many types of seats and lids, make sure to select a toilet seat that will fit your toilet model. ...
- Find the correct toilet seat size by measuring your new toilet if necessary.
- A specialty item such as a raised or heated toilet seat may have special installation requirements.
How much room is required to install a toilet?
You’ll probably want at least 1 ft. on either side of the toilet and 2 ft. in front, but this is still a small space for a toilet. Code requirements may list minimum spaces, and they can vary by city and county.
How to install commode kit?
- If not already attached, install the “tank to bowl” gasket onto the base of the flush valve. ...
- Place the tank onto the bowl, aligning the shank of the bolts with the holes in the bowl. ...
- Secure the tank to the bowl by alternately tightening each tank bolt until the tank pulls down and meets the bowl.
How to install an upstairs toilet?
How to Install an Upstairs Toilet
- Install one of the bolts from a toilet-bolt kit in each of the slots on each side of the toilet flange at the floor.
- Fit a new wax ring onto the recess around the drain hole in the flange. Push down lightly on the ring to seat it at the flange.
- Ask an assistant to help lift the toilet bowl and align the holes at the base on each side with the bolts.
How do you install a fluidmaster complete toilet repair kit?
0:127:14SUPER EASY Toilet Repair Using Fluidmaster Universal Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe kit contents is the fill valve the flapper and assortment of parts a little hose and theMoreThe kit contents is the fill valve the flapper and assortment of parts a little hose and the instructions. So first we have to turn off our water supply. And then remove the existing valve.
How do you install toilet tank hardware?
2:2614:13How to Fix a Running Toilet & Replace All Internal Toilet Tank PartsYouTubeStart of suggested clipEnd of suggested clipAnd a pair of pliers for the bolt and nut underneath the tank to loosen that up. This is what we'reMoreAnd a pair of pliers for the bolt and nut underneath the tank to loosen that up. This is what we're using to replace the internal parts of that toilet tank it's made by Fluidmaster.
Are all toilet repair kits the same size?
Toilet repair kits come in a variety of sizes. Some may come with one part, while others include every component in your tank.
How do you install a Korky toilet fill valve and flapper kit?
0:083:34How to Install Platinum Toilet Fill Valve & 2" Flapper Kit - 818MPYouTubeStart of suggested clipEnd of suggested clipInstall the new flapper attach the flapper ears to the tabs of the flush. Valve attach the flapperMoreInstall the new flapper attach the flapper ears to the tabs of the flush. Valve attach the flapper chain to the flush lever with minimal slack. Turn the water supply on and wait for the tank to fill.
How do you install tank bolts?
2:344:14How to Replace Toilet Tank to Bowl BOLTS and Gasket - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow put the tank onto. The bowl from below install a rubber washer a steel washer and a wing nut iMoreNow put the tank onto. The bowl from below install a rubber washer a steel washer and a wing nut i just got the nut started not completely tightened down repeat for the other bolts.
How tight should toilet tank bolts be?
Get the bolts snug but not tight. Some tanks have built in lugs that will contact the bowl. If yours has these, stop when they contact the bowl. You can fill the tank and look for leaks at the bolts.
How do I know what size toilet repair kit I need?
Look at the flush valve drain opening at the bottom of your tank. If the opening looks about the size of a baseball or orange, you need a 2″ flapper. If the opening looks about the size of a softball or grapefruit, you need a 3″ flapper.
How do I know what model toilet I have?
Identifying Your Toilet ModelToilet model numbers are located in a variety of places on the product.One-piece toilet: The model number is located inside the tank.Two-piece toilet: Model numbers are found inside the tank and the bowl, and are specific for those parts of the toilet.More items...
Which one is better korky or Fluidmaster?
The Korky gasket material is nice and spongy, yet sturdy – the quality feels better to me than the Fluidmaster. As with replacement flush valves, there's more than one size of gasket available. 2 inch is by far the most common, with some newer toilets using 3 inch valves....FluidmasterModel 61022″KorkyModel 481BP3″2 more rows
How do you install a korky fill valve on a toilet?
0:041:52How to install a Toilet Fill Valve by Korky - YouTubeYouTubeStart of suggested clipEnd of suggested clipWater disconnect your water supply line and remove the mounting nut remove. The old fill valve. TurnMoreWater disconnect your water supply line and remove the mounting nut remove. The old fill valve. Turn the top of your new fill valve counterclockwise. And pull up to fully extend.
How do you adjust a Korky toilet fill valve?
0:412:20Korky QuietFill Toilet Fill Valve Troubleshooting guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the valve is set to high turn off the water supply. And flush the toilet adjust. The height ofMoreIf the valve is set to high turn off the water supply. And flush the toilet adjust. The height of the valve by twisting the top half of the valve counterclockwise.
How do you adjust korky flapper?
1:312:21How to install a Korky Ultra Water Saver Toilet Flapper - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe quirky ultra water saver flapper. Allows you to find two new flapper for optimal control adjustMoreThe quirky ultra water saver flapper. Allows you to find two new flapper for optimal control adjust the dial to align with the next lowest number using the arrow.
What are the parts in a toilet tank?
Here are five critical parts of a typical toilet tank's anatomy.Rubber Flapper. The round, flat rubber flapper covers the hole at the bottom of the tank where water runs out to the toilet bowl when you flush. ... Fill Valve. ... Fill Float. ... Flush Lever and Chain. ... Overflow Tube.
Can you use plumbers putty inside toilet tank?
Historically, plumber's putty was used to seal a leaky toilet or toilet bowl to a finished floor. However, we do not recommend using plumber's putty for these types of applications, as this product can't support the weight of a toilet and is not waterproof.
How do you replace a fill valve on a toilet?
1:023:58How to Fix a Toilet - Fill Valve Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipReach behind the fill valve and snap the lock ring down into place then attach the refill tube toMoreReach behind the fill valve and snap the lock ring down into place then attach the refill tube to the overflow tube and adjust the new fill valve for optimum water level.
How do you fix a toilet flush valve seal?
0:151:32How to Install a Toilet Flush Valve Seal for American Standard and ...YouTubeStart of suggested clipEnd of suggested clipNext unscrew the black nut and remove it remove the o-ring using your fingernail or tweezers. AndMoreNext unscrew the black nut and remove it remove the o-ring using your fingernail or tweezers. And replace with the black o ring remove the green cover and replace the old. Seal.
What is included in Fluidmaster Complete Toilet Repair Kit?
The kit includes a new fill valve assembly, a flush valve assembly with adjustable flapper valve, a flush lever, a rubber fill tube, new gaskets, new tank bolts with nuts, rubber washers and metal washers.
What is Fluidmaster Complete Repair Kit?
This Fluidmaster Complete Repair Kit (model # 400AKR) came with wing or "thumb" nuts to help keep the standard nuts on the tank bolts from loosening. The original toilet tank bolts did not have these, but I figured they couldn't hurt and threaded the wing nuts on to the bolts below the other nuts.
Where is the flush handle on a toilet?
Unscrew the white plastic nut that secures the chrome colored flush handle and lever to the top left of the toilet tank.
Where do you pull the lock nut out of a tank?
Once the lock nut is removed from the bottom of the fill valve, you can pull it out from the inside of the tank.
How to separate a cone washer and shank washer?
The shank and cone washers are attached to each other by three little pieces of rubber. Pull them apart by hand or carefully use a utility knife or X-Acto knife. The shank washer is the larger piece and the cone washer is the smaller piece.
