How To Install A Harmonic Balancer Sleeve
- You should clean the shaft and wear grooves with a brake cleaner.
- Put adhesive on the shaft.
- You will need to drive the repair sleeve onto your shaft using the installation tool.
- Install a new crankshaft oil seal.
- Rub a small quantity of engine oil to the outside of the repair sleeve and then seal it.
Full Answer
How do you reinstall the harmonic balancer?
Part 1 of 1: Replacing a harmonic balancer
- Breaker bar (½” drive)
- Combination wrench set
- Floor Jack
- Gear puller
- Jack stands
- New harmonic balancer
- Screwdriver set
- Socket set (½” drive)
- Strap wrench
- Torque wrench (½” drive)
How do you fix a harmonic balancer?
- Helps keep the momentum of the engine
- Smoothes out engine vibrations
- Drives the main serpentine belt
- Is used by the front main oil seal
- Can fail causing engine noise
What tool is needed to replace a harmonic balancer?
- The engine sounds are louder than usual and you feel abnormal vibrations coming from the engine.
- The belt in the pulley might slip which will cause the vehicle to misfire or backfire.
- The ignition timing in the vehicle will be off.
- The vehicle might not start at all if the balancer is broken.
When do you need to replace a harmonic balancer?
This depends on how many miles you have been driving the car or how old the car has actually become. There is no fixed time for this but there are symptoms from which it can be inferred that the balancer needs a replacement.
How do you install balancer sleeves?
1:293:21V-8 Engine Rebuild SBC #7 Harmonic Balancer Sleeve Install - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to have to put just enough heat on it so that we expand. It a little bit so that it goesMoreWe're going to have to put just enough heat on it so that we expand. It a little bit so that it goes on easier and we want to use the block of wood to push it on gently with a hammer.
Can harmonic balancer be repaired?
The good news is, the harmonic balancer can easily be repaired with a kit that usually retails for under $10.
How do you install a harmonic balancer press fit?
0:275:10Robert Dana teaches you how to install a Harmonic Balancer.YouTubeStart of suggested clipEnd of suggested clipBecause this is a press fit onto the crankshaft. Like that okay now we're going to put the harmonicMoreBecause this is a press fit onto the crankshaft. Like that okay now we're going to put the harmonic balancer on the crank. And line it up with the the dowel pin.
How do you install a harmonic damper?
2:288:57How to install a harmonic balancer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis piece also slides on the shaft. Then rise up against the front of your balancer. So thatMoreThis piece also slides on the shaft. Then rise up against the front of your balancer. So that there's no galling as it pulls it in.
Can I weld my harmonic balancer?
Welding the hub to the crank will almost certainly pass enough heat to the rubber portion of the balancer to damage it. Best to repair whatever situation is making you consider welding the harmonic balancer to the crankshaft.
How do you fix a harmonic balancer?
1:038:49Fix a broken Crankshaft Pulley Harmonic Balancer Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipSet time is four to six hours cure time is 15 to 24 hours in cure color dark grey.MoreSet time is four to six hours cure time is 15 to 24 hours in cure color dark grey.
Do you need a tool to install a harmonic balancer?
Proform Harmonic Balancer Installation Tools are used for installing the harmonic balancer. They use a pilot stud, which keeps the harmonic balancer perpendicular to the crankshaft's centerline, for a bind-free installation.
How do you install a harmonic balancer without tools?
1:5511:14How to Install Any Harmonic Balancer "With A $2.00 Homemade Tool ...YouTubeStart of suggested clipEnd of suggested clipLet's take a socket. And lightly tap it in until you can start a boat. Tool. You do not want to hitMoreLet's take a socket. And lightly tap it in until you can start a boat. Tool. You do not want to hit this very. Hard like taps won't hurt. Big top soil okay. So here's the original bowl.
Why does my harmonic balancer wobble?
Noticeable Harmonic Balancer Wobble When the rubber isolator begins to deteriorate, the balancer usually begins to separate, creating a noticeable wobble when the engine is running.
How do you install a crankshaft damper?
1:5610:11How to remove a harmonic balancer pulley. How to install a ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll right so you merely set the pulley on the crankshaft. Thread this in drive it in and simplyMoreAll right so you merely set the pulley on the crankshaft. Thread this in drive it in and simply drive the nut on.
How do you tighten a harmonic balancer bolt?
0:003:48Torque Crank Bolt/Harmonic Balancer No Special Tool - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt goes at 217 foot-pounds. And you need a way to keep this from spinning to hold it like tightenMoreIt goes at 217 foot-pounds. And you need a way to keep this from spinning to hold it like tighten this you could also use this to loosen it the way I loosen it I just crank the engine.
How do you use a harmonic balancer puller installer?
0:422:51HARMONIC BALANCER REMOVER & INSTALLER SET ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe inside of the puller screw is hollow with threaded walls because it's designed to thread overMoreThe inside of the puller screw is hollow with threaded walls because it's designed to thread over the adapter. Next push the puller flange over the puller body with the flat side facing the radiator.
How much does it cost to repair harmonic balance?
The cost to replace the harmonic balancer could be around $100 to $500 depending on your vehicle type.
How much is it to fix a harmonic balancer?
Crankshaft Harmonic Balancer Replacement pricing for various carsCarsEstimateAverage Dealer Price2015 Kia Optima$450$466.722012 Chevrolet Suburban 1500$395$425.362014 Hyundai Genesis$371$390.032009 Mercedes-Benz SLK350$460$477.472 more rows
What happens when harmonic balancer fails?
If the harmonic balancer gets too old or fails and can no longer properly absorb the harmonic vibrations, the engine will shake excessively. The shaking will become even more pronounced, and therefore dangerous to the engine at high speeds.
How do I know if my harmonic balancer needs replacing?
The most common symptoms of a bad harmonic balancer include:Engine Vibrations. The harmonic balancer's job is to dampen vibrations applied to the crankshaft. ... Noticeable Harmonic Balancer Wobble. ... Unusual Noises. ... Illuminated Check Engine Light. ... Visible Wear or Damage.
How to remove harmonic damper?
The first step is to remove the harmonic damper with the proper tool, known as a puller. This tool works like most pullers attaching to the harmonic balancer with bolts. During operation, the puller employs a jackscrew complete with a protection plate that pushes the balancer off. You never want to pry a harmonic balancer off the crankshaft. Many engines built over the last 20 years do not use a keyway in the balancer and crankshaft snout. This design is just an interference fit, and its use is based on the accessory load that is run from the crankshaft pulley.
What happens if the timing cover seal is worn?
An all-too-common mistake when changing a front timing cover seal is not inspecting the hub of the harmonic balancer for wear. It may be hard to believe, but the seal can actually cut a small groove into the hub of the balancer. When this happens and the new seal is installed, ...
Can you pry a harmonic balancer off the crankshaft?
You never want to pry a harmonic balancer off the crankshaft. Many engines built over the last 20 years do not use a keyway in the balancer and crankshaft snout. This design is just an interference fit, and its use is based on the accessory load that is run from the crankshaft pulley.
Can a harmonic balancer be repaired?
Instead, the groove allows for oil to migrate out. The good news is, the harmonic balancer can easily be repaired with a kit that usually retails for under $10.
Can you replace timing cover on crankshaft?
Though the timing cover crankshaft (front) seal is much easier to replace than the rear main seal, it can offer its own set of challenges. In many applications, getting to the seal is burdensome, and more times than not, you end up removing the timing cover.
Can you damage a crankshaft by ramming it against its end?
You will most likely damage the balancer and injure the crankshaft by ramming it against its end. When the balancer is removed, inspect it before deciding to install a repair sleeve. If the design allows, inspect the condition of the rubber dampening ring to see if the material is still soft and spring-like.
Can you match timing cover seals?
If you have a willing sales rep, that person will pull out a couple of different parts numbers and you can then match to the dimensions you need. This works great on older engines and ensures you a leak-free timing cover seal repair job!
How to remove harmonic damper?
The first step is to remove the harmonic damper with the proper tool known as a puller. The tool works like most pullers and attaches to the harmonic balancer with bolts. Then, a jackscrew with a protection plate for the crankshaft thread pushes the balancer off. You never want to pry a harmonic balancer off the crankshaft.
How to sleeve a non-automotive engine?
If you need to sleeve a non-automotive engine, measure the hub diameter and length with a caliper and go to the auto part store. If you have a willing, old-school counterman, he will pull out a couple of different parts numbers, and you can then match it up to the dimensions you need.
How to check if a dampening ring is still soft?
If the design allows, check the rubber dampening ring condition to see if the material is still soft and spring-like. You can use the end of a screwdriver for this but be gentle, you do not want to puncture it. Check to ensure there are no cracks in the harmonic absorbing material and that no pieces are missing. If it does not pass muster, save the ten dollars for the sleeve, and put it toward a new balancer.
What is the three leg stool of success?
My name is Ray Bohacz, and I know that success on the farm is a three-legged stool: agronomy, business, and machinery. I have always believed and life has taught me, that great judgement in the first two areas can quickly be evaporated by poor decisions in the farm shop in regard to maintenance and repair.
Can a harmonic balancer be repaired?
It is not due to the seal being faulty; the groove allows for the oil to migrate out. The good news is the harmonic balancer can easily be repaired with a kit that usually retails for under $10.00. There are some caveats, though. The first step is to remove the harmonic damper with the proper tool known as a puller.
When removing a balancer from a car, is it necessary to inspect it?
When the balancer is removed from the engine, it is essential to thoroughly inspect it before you decide to install a repair sleeve. If the design allows, check the rubber dampening ring condition to see if the material is still soft and spring-like.
Can you damage a balancer by ramming it?
You will most likely damage the balancer and injure the crankshaft by ramming it against its endplay.
cudavert DARTAHOLIC
I think that thing is smoked. I dunno what happened.....maybe you pressed it on cockeyed or too far.....?
mikedevore Well-Known Member
The wood distorts when you press on it, causing the sleeve to distort.
burdar Owen's Dad
The sleeve I installed on my 318 had a wider lip on it for you to press against.
Reddartowner UCF Alumni....Go Knights!
Get a speedi-sleeve. They come with an "installation tool", a collar that mates with the lip on the sleeve. You need to purchase the correct sleeve for the shaft you are repairing. If the sleeve is loose you can use a 2 part liquid epoxy to take up a small amount of clearance and retain the sleeve.
Andre68 Well-Known Member
Where can i purchase the speedi sleeve? and is there a specific part number?
Treblig Well-Known Member
I always thought that you heat the sleeve in the oven to about 250 degrees an cool the balancer in the fridge then it should slide right on. You gotta be quick so the sleeve doesn't have time to cool off. Be sure and use some good gloves so you don't get burned!!
Treblig Well-Known Member
Anytime to tap on a ring with a hammer it gets larger. Haven't u ever watched someone "size" a ring for your finger??
What is harmonic balancer?
The harmonic balancer is attached to the crankshaft and smooths vibrations from the engine. The crankshaft pulley usually bolts on to the front of the harmonic balancer. The harmonic balancer shaft passes through the timing cover, which includes a rubber seal to seal the shaft against oil leaks. Over time, this seal can wear a ridge in ...
Can a harmonic balancer wear a ridge?
Over time, this seal can wear a ridge in the balancer shaft. If the harmonic balancer is in otherwise good condition, a harmonic balancer repair sleeve can be used. This sleeve press fits to the balancer shaft and provides a smooth surface for the timing cover seal. To service the balancer, you'll need a harmonic balancer puller and installer, ...
