Repairing Guides

how to mud a ceiling repair

by Elisha O'Hara Published 2 years ago Updated 2 years ago
image

How to Repair a Mud Swirl Ceiling

  • Step 1 - Practice the Pattern of the Swirl Ceiling. Match the texture before you begin working on your swirl ceiling.
  • Step 2 - Remove the Damaged Section of the Swirl Ceiling. Remove the damaged portion of the ceiling. You don't need to...
  • Step 3 - Attach a New Section of Drywall. Measure the area that is now free of drywall. Cut a new...

Part of a video titled Mudding And Taping A Ceiling Repair After Water Damage
6:01
15:49
Super simple tears easy start in the middle. Then start in the middle and go the other. Direction.MoreSuper simple tears easy start in the middle. Then start in the middle and go the other. Direction. Now this is a pretty heavy textured ceiling.

Full Answer

How to stomp texture a ceiling?

What Are The Popular Stomp Ways?

  • Splatter Knockdown. If you are contemplating how to stomp a ceiling, one pattern you can opt for quite easier is, splatter.
  • Popcorn Texture. This popcorn texture is also quite popular among unconventional design lovers. ...
  • The Orange Peel Texture. Once you are done with the procedure of stomping the wall, it will look like an orange peel. ...

How to hang drywall on a ceiling?

to hang drywall on a concrete or brick ceiling, you can use joint compound as mastic. You mud the backside, create a 2x4 "T" to hold it tight against the ceiling and then nail it in with concrete nails. You can also rent a drywall hoist to push it tight to the ceiling.

How to apply drywall Stomp texture to ceiling?

Stomp Knockdown Texture

  • Type of Mud. ...
  • Consistency of the mud. ...
  • Apply with a paint roller or heavy duty airless paint sprayer. ...
  • Stomp a random pattern in the mud. ...
  • Allow to set and knock it down lightly. ...
  • Below are a few more examples of Stomp-Knockdown textures
  • Back to more texture types. ...

How to repair a drywall ceiling hole fast and easy?

Drywall Ceiling Repair for Large Holes Cut a rectangle around the damaged area. Add wooden cleats behind each side for support. Attach a patch piece to the cleats. Place mesh tape over the patch piece and spread joint compound. Apply a second and third coat of the compound over repairs and then sand until smooth.

image

What kind of mud do you use for ceiling?

Drywall compound, commonly referred to as mud, textures ceilings in a wide variety of patterns. These patterns add character and interest to your room and break up the monotony of a flat ceiling. As an added benefit, textures conceal imperfections, stains and repaired areas.

Can I use joint compound to repair ceiling?

Drywall Ceiling Repair for Large Holes Attach a patch piece to the cleats. Place mesh tape over the patch piece and spread joint compound. Apply a second and third coat of the compound over repairs and then sand until smooth. Clean with a damp rag to remove dust; prime and paint the ceiling to match.

What type of mud do you use for ceiling drywall?

All-purpose mud is commonly used as a first coat because the bonding agents in the mud cause the drywall tape to hold better. All-purpose mud is harder to sand and not often used as a finish coat. Topping mud is a form of dry mud that is lighter than all-purpose. It is best used for final coats.

How do you mud a ceiling wall joint?

0:426:27How to tape and finish a inside drywall corner - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the knife to scoop the mud out of the bread pan scoop it from both sides of the knife use theMoreUse the knife to scoop the mud out of the bread pan scoop it from both sides of the knife use the knife to scoop out the mud one side for the ceiling. And the other side for the wall.

How do you mud a ceiling?

0:539:06EASIEST WAY to Drywall Finish a Ceiling for Beginners! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo basically you just want to get your mud up there fill your knife not completely full of mud justMoreSo basically you just want to get your mud up there fill your knife not completely full of mud just kind of control it keep it in the center. And you're gonna come back and wipe it. Down.

How do you mud texture a ceiling?

2:576:27Best and Fastest Way to Texture a Ceiling - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust basically want to keep that mud. Up. So now what you want to do is you want to do it inMoreJust basically want to keep that mud. Up. So now what you want to do is you want to do it in sections. And do a third no more than a third of the ceiling at a time roll.

What is the difference between drywall mud and spackle?

Hardware stores stock a variety of types of spackling paste for filling holes prior to painting, but in a pinch, you can always use drywall joint compound. The main difference between them is that spackling paste resists shrinking and is formulated primarily for filling smaller holes.

What kind of mud do you use for texture?

You can use either dry compound or ready-mix compound. Avoid compounds that contain sand or grit (unless you want a unique look). Plain mud works best for this type of texture. You should also avoid lightweight compounds.

What is the difference between joint compound and mud?

Joint compound, commonly called mud, is the wet material that is used for drywall installation to adhere paper joint tape, fill joints, and to top paper and mesh joint tapes, as well as for plastic and metal corner beads. It can also be used to repair holes and cracks in drywall and plaster.

Can you use joint compound to texture a ceiling?

You can use a ready-to-use multi-purpose joint compound, a ready-mixed texture compound, or a powdered texture compound that you mix yourself.

Can you use drywall compound on ceiling?

Refresh old designs with a different texture or create one from scratch using drywall joint compound. Buy joint compound in 5-gallon buckets. You will need to add water to thin it for application to a ceiling. You don't even need to add paint if you want a white ceiling, and it will look good for many years.

How do I fill gaps in my ceiling?

How to fill a gap between drywall and ceilingStep 1: Mesh drywall tape. Start by placing a strip of fiberglass mesh drywall tape over the gap so that the top edge of the tape is flush against the ceiling.Step 2: Apply joint compound. ... Step 3: Paper tape. ... Step 4: More mud. ... Step 5: Let the mud dry. ... Step 6: Sand. ... Step 7: Paint.

Can I use joint compound to texture ceiling?

You can use a ready-to-use multi-purpose joint compound, a ready-mixed texture compound, or a powdered texture compound that you mix yourself.

Can you use drywall mud for ceiling texture?

Textured ceilings perfectly camouflage imperfections like cracks or evidence of water damage. There are a variety of techniques you can employ to create your texture of choice (way beyond the “popcorn” look popular in the 1970s). All it takes is a mixture of paint and drywall mud—and a little ingenuity.

Can you tape and joint a ceiling?

Once you have hung the ceiling and the walls, you can move on to mudding and taping the drywall ceiling. For the first part, you will need premixed joint compound (drywall mud) and a 5-inch utility knife.

Can you put joint compound over popcorn ceiling?

1:037:05Can I skim coat over my painted popcorn ceiling? DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you mix it too thin you're gonna have to do multiple coats to cover this popcorn ceiling it'sMoreIf you mix it too thin you're gonna have to do multiple coats to cover this popcorn ceiling it's going to take two coats of skin.

How to keep a ceiling from cracking?

If the ceiling crack is near a wall, consider covering the wall with a plastic drop cloth to keep splatters off.

Can you fix a crack in the ceiling?

While repairing cracks on walls is pretty straightforward, it’s a bit more complicated with ceilings, which typically have some type of texture applied and are overhead, making the repairs a (literal) pain in the neck. By following a few time-honored techniques, a savvy homeowner can often successfully repair cracks in ceilings without too much ...

Can you dry wet drywall before applying a new coat?

DON’T shorten time for drying. Ceiling crack repairs made with wet drywall compound should be completely dry before another coating is applied. The general rule-of-thumb here is to apply the mixture in the thinnest coat possible, making sure to remove excess with a taping knife.

Can you cover popcorn ceilings with drywall?

Since this type of ceiling can actually reduce a home’s market value, this may be an excellent time to get rid of the texture or cover it up with drywall panels or rigid foam panels. Popcorn ceilings installed before 1978 may contain asbestos, so it’s vital to find out what type of popcorn texture is on your ceiling before making repairs.

Do you need a dust mask when sanding drywall?

DON’T forget to stay safe. Sanding drywall compound can create billows of dust, and a DIYer should wear a dust mask in addition to eye protection before tackling the task. In addition, when working overhead, use only a sturdy step ladder (no wobbly chairs or stools) in order to reach the ceiling. istockphoto.com.

Tips

Follow these easy tips, and watch the video to make quick work of ceiling repair, ranging from cracks in the ceiling to nail pops, large holes and even removing popcorn ceilings.

How to Remove Popcorn Ceiling

No longer a fan of that popcorn ceiling? It's easier to remove than you might think. Follow these tips from our DIY Basics video: How Do I Remove Popcorn Ceiling?

Prep Work

Painted popcorn ceiling removal is challenging. Test a small area in a corner to see if your ceiling is painted or not.

What to do if you get texture wrong?

Texturing is something like an art, and you may get it wrong the first time. If so, scrape off the texture and try again.

How to fix popcorn texture?

Spray dilute joint compound with a hand sprayer to repair popcorn texture. If the ceiling has a knock-down texture, scrape the sprayed blotches lightly with a drywall knife to flatten them. Other textures may require the use of other tools, such as a slap brush or paint roller.

How to fix blisters in plaster ceiling?

If the blistering occurred at a seam between drywall panels, or if there are cracks in the plaster core, cover them with joint tape to keep the repair from cracking. Mix up a small batch of 20-minute setting-type joint compound to a peanut-butter consistency, mist the ceiling with water from a spray bottle—that ensures the compound will set properly—and apply a thin layer of compound to the ceiling with the taping knife. Then use it to press the tape into the wet compound, as shown.

How to smooth out a tape layer?

After the tape layer hardens, mix a bigger batch of joint compound and transfer it from the bucket to the ceiling with the 6-inch taping knife. Now switch to a 12-inch taping knife and use it to smooth the compound and feather its edges. Wait several minutes for the compound to firm up, then mist and smooth it some more. With patience, you can eliminate most imperfections with the knife before the compound becomes too hard to work.

How to remove blemishes from a compound?

When the compound is hard, use a medium-grit sanding sponge to erase any blemishes. Pay particular attention to the edges.

What is drywall tape made of?

Most tape that bridges drywall joints is made of paper (above, top). It’s strong and inexpensive, but absorbs moisture and doesn’t bond well with joint compound. Fiberglass mesh tape (middle) isn’t affected by moisture and becomes fully embedded in the compound.

How to protect drywall from mud splatter?

STEP 1: Protect the floor and yourself from drywall mud splatter. Cover the floor with a canvas drop cloth (plastic drop cloths can become dangerously slick) and don goggles and old clothing. Mudding is a messy process, and splatters can sting if they get in your eyes. Advertisement.

What is drywall mud?

Powdered. Powdered drywall mud, also called “setting mud” or hot mud,” contains chemicals that react when water is added to hasten hardening time. This type of mud tends to shrink less than all-purpose premixed mud but it begins to harden very quickly.

How to use paper tape in mud?

Smooth the paper tape carefully in the wet mud, using either a 6-inch taping knife or an inside-corner taping tool that features a preformed 90-degree shape for easy bedding. Use light stroking movements to bed the tape without dislodging it from the corner. Wipe excess mud from the walls.

How to make a mud sanding tool?

With the 6-inch knife, apply a thin coat of mud to both sides of an inside corner, making sure to work it all the way into the center. Cut, fold, and fit a strip of pre-creased paper tape in the corner over the wet mud. Smooth the paper tape carefully in the wet mud, using either a 6-inch taping knife or an inside-corner taping tool that features a preformed 90-degree shape for easy bedding. Use light stroking movements to bed the tape without dislodging it from the corner. Wipe excess mud from the walls.

What is tape used for in drywall?

During the mudding process, tape acts as a bond to keep the finished wall from developing cracks along the drywall seams. The different types of tape are “paper,” “mesh,” and “preformed”—and all three have their pros and cons.

How to smooth mud from a joint?

Cut and fit a piece of paper tape over the joint while the mud is still wet for a process called “bedding.” Use the 6-inch taping knife to gently smooth the paper onto the wet mud, working out bubbles as you go. Wipe away excess mud with the knife.

How wide is a dry wall?

Drywall panels come with slight bevels on both of their long sides. When the bevels are fitted together, they form a small indentation, about 2 inches wide, along the joints. Use the 6-inch taping knife to smooth and work the mud evenly into the joint, filling the entire indentation and wiping away excess mud.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9