If you need to repair your Maytag washing machine start button or any other appliance or electronic device, apply light pressure to the regions around the start button. You can also tap the areas around the button; this may help dislodge any foreign material that might be stuck between the button and make it function normally again.
How much should you pay for Maytag washer repair?
Appliance repair costs $172 on average, with a typical range of $105 and $240. This includes parts and $50 to $150 per hour for professional service. Although this range includes most common appliance problems, there are several factors that may affect the total. If the unit is more than 10 years old, runs on natural gas or cost $5,000 when you ...
What are some ways to Reset my Maytag washing machine?
- Turn off your Maytag Centennial washing machine.
- Disconnect it from electricity socket. Keep it in this condition for 11 to 17 minutes.
- Plug your washer cable back to wall outlet.
How to troubleshoot why a Maytag dryer is not working?
Maytag Dryer Won’t Start – Troubleshoot and Diagnosis
- Incoming Power Problem. If your Maytag dryer is not turning on, the first step is to check power. ...
- Incorrect Dryer Settings. If your Maytag dryer lights up yet will not start, first check your settings. ...
- Door Not Latched Properly. ...
- Blown Thermal Fuse. ...
- Defective Dryer Start Switch. ...
- Bad Belt Switch. ...
- Faulty Drive Motor. ...
What are some common problems with Maytag washers?
Maytag Washer Won’t Start – Troubleshoot and Diagnosis
- Incoming Power Problem. Washing machine troubleshooting is one of the most common complaints that plagues appliance owners. ...
- Do a Hard Reset. ...
- Maytag Washer Start Button Stuck. ...
- Control Lock is Turned ON. ...
- Incorrect Washer Settings. ...
- Faulty Lid Switch. ...
- Defective Control Board. ...
- Broken Timer. ...
- Faulty Motor. ...
See more
How do you lift the lid on a Maytag washer?
0:121:42How to remove the top from a Maytag Bravos XL washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut if you take off the top bolt of both of those. Pull those out you'll find that you can put theMoreBut if you take off the top bolt of both of those. Pull those out you'll find that you can put the top part forward toward you and as you pull it toward you you can lift it up.
How do you open up a Maytag washer?
0:293:39How to Replace the Spin Basket on a Maytag Vertical Modular Washer ...YouTubeStart of suggested clipEnd of suggested clipPull. The bottom of the tub ring to release it from the locking tabs on the side of the outerMorePull. The bottom of the tub ring to release it from the locking tabs on the side of the outer plastic wash tub use a slot screwdriver if necessary pull the tub ring out of the washer.
How do you open the bottom of a Maytag washer?
0:363:57How To: Whirlpool/KitchenAid/Maytag Washplate WPW10215115 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you have to do is stick the screwdriver into the slot right here you can turn a little bit toMoreAll you have to do is stick the screwdriver into the slot right here you can turn a little bit to break it free you can lift the cap out set it aside.
How do you open the top of a Maytag front load washer?
Pull out on the bottom of the front panel of the machine and then pull down to unsnap the two plastic clips at the top of the front panel. Once the two top clips have unhooked, remove the front panel entirely and set it aside.
How do you open a top loader washing machine?
0:002:48How To Open Your GE Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you're basically just pushing inside very gently and then once you push that in you'll be ableMoreAnd you're basically just pushing inside very gently and then once you push that in you'll be able to pull this forward you'll hear him push end.
How do you take apart a Maytag front load washer?
3:4614:58Maytag Washer Repair - Bearing and Seal Failure - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you just want to pull these two screws out and the reason for doing that is that this retainsMoreAnd you just want to pull these two screws out and the reason for doing that is that this retains the front cover. So it just pops off like that as soon as you get those screws out.
How do you remove the middle of a washing machine?
0:282:50How to Clean, Remove and Replace the Agitator in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipAnd then write down the center of the agitator as a little wound yard remove that just hold theMoreAnd then write down the center of the agitator as a little wound yard remove that just hold the agitator as you unscrew anticlockwise.
How do you remove the tub from a Maytag washer?
Twist the boot seal clockwise to loosen and remove the boot seal. Take care not to grab the boot seal around the carbon ring. Remove the three bolts that secure the outer tub to the tub braces with a wrench. Pull the outer tub out of the Maytag washer.
How do you take apart a Maytag agitator?
0:573:07How To: Whirlpool/KitchenAid/Maytag Agitator Assembly WP22004042YouTubeStart of suggested clipEnd of suggested clipYou're going to use a ratchet with 1/2 inch socket and extension to remove the bolt that's down inMoreYou're going to use a ratchet with 1/2 inch socket and extension to remove the bolt that's down in the center that holds the agitator in place. So when in a counterclockwise.
How do you open the top of a Maytag Neptune washer?
3:3720:52Maytag Neptune Washing Machine Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipI have to remove that screw down there at the hinge screw up there at the hinge. I have to removeMoreI have to remove that screw down there at the hinge screw up there at the hinge. I have to remove these two screws and these plastic connectors here so the front can pop off.
THE WASHING MACHINE WON’T DRAIN
If your washing machine won’t drain or your loads are coming out too wet, you may have a kink or clog in the drain hose, a drain pipe that’s too lo...
MY WASHING MACHINE WON’T SPIN
A washer needs to spin correctly in order to fully rinse clothes and drain water from the tub. Before scheduling a service call, check if the power...
WASHING MACHINE IS LEAKING
Water is meant to stay in the washer. But if you’re noticing some water appearing on the floor, it may be a simple fix. Try cleaning the door seal,...
MY WASHER IS NOISIER THAN EXPECTED
If you’ve just brought home a new washer, it’s possible that it makes some noises you aren’t familiar with. Many of these are normal and shouldn’t...
MY WASHER HAS ODORS
Washer odors are easily fixable and usually the result of a missed cleaning, a load left too long or too much detergent and fabric softener use. Tr...
How to contact Maytag for repair?
If you need professional repair help, schedule service online or call 1-800-344-1274.
How high should a Maytag washer drain be?
Washers have minimum and maximum drainpipe height requirements. For most Maytag ® washers, the drainpipe should be installed at a maximum of 96" and a minimum of 39" from the bottom of the machine. Your washer will not be able to adequately pump water out of the washer if the drainpipe reaches too high. In this case, water may flow back ...
Why is my washer not spinning?
If not, the load may become unbalanced, causing the washer not to spin properly. This can also cause excessive noise and vibration, especially during the spin cycle. Learn the right way to level a top load washing machine or front load washing machine .
Why does my washer make a clicking noise?
Many washer lids make clicking noises while they’re locking in place at the beginning of a cycle. It’s also normal to hear metal items on clothing like buckles or zippers touch against the stainless steel basket. Always empty your pockets before putting clothes in the washer—it’s possible for coins or other items to fall between the basket and the tub, which may require a service call.
Why won't my washing machine drain?
The washing machine won’t drain. If your washing machine won’t drain or your loads are coming out too wet, you may have a kink or clog in the drain hose, a drain pipe that’s too long or a slow-spin option selected.
Does Maytag have a washing machine cleaner?
Your washer may have its own cleaning cycle or even recommended cleaner. Maytag recommends affresh® washing machine cleaner tablets 1 , but you can use common household items as well. Learn how to clean your washer in four simple steps.
Step 1
Remove all of the clothes from the washing machine, then disconnect the power to the appliance. Power can be disconnected by either unplugging the washing machine from the wall or by turning off the breaker in your fuse box.
Step 2
Remove the two screws on the bottom of the front panel of the washing machine.
Step 3
Pull the bottom of the front panel out to release the two tabs at the top of the washing machine. Remove the panel once the tabs are released.
How to repair Maytag washer?
The best way to make repairs on your Maytag washer is to take the washer cabinet apart. When you take apart the Maytag washer you will have full access to all of the working mechanisms inside the washer. This makes repairs quicker, and will also provide an opportunity to test and troubleshoot the entire washer.
How to disconnect Maytag washing machine?
Disconnect the Maytag washing machine power cord from the wall. Turn off the water at the wall spigots. Pull the washer away from the rear wall and set a bucket under the water supply hoses at the back panel of the washer.
How to clean a washer with residual water?
Loosen the water hose connections from the back of the washer with a pair of channel lock pliers. Remove the hoses from the washer and place the ends into the bucket. There will be residual water, so it is a good idea to also have a towel nearby to wipe up any spills.
How far from the floor should you remove screws from a Maytag washing machine?
For starters, look at the first-lower corners of your Maytag washing machine. Approximately four inches from the floor, you should see a pair of screws.
Where are the washer bolts on a washing machine?
They are 3/8-inch big and are generally in the upper right-hand corners at the front of the washing machine. That is the case when the top of the washer won’t hinge upward. Take out the bolts using your ratchet and keep them off safely to the side.
Why is it important to fix the locking mechanism on a washing machine?
That said, when the lock isn’t working properly, the machine may also not run. So, it is important to fix the locking mechanism so that you can run your cycles as normal.
When you are done inspecting or repairing the problem, just follow the steps in reverse.?
When you are done inspecting or repairing the problem, just follow the steps in reverse. Make sure that any portion with bolts or screws are tightened properly before closing everything up and calling it a day. Loose components can potentially become damaged or come out entirely under the worst-case scenario.
Most Common Problems
The Maytag washing machine troubleshooting process begins with Repair Clinic's list of symptoms. Once you match your problem to one of the common technical causes we've included in our troubleshooting guide, you'll be on your way to a quality repair.
The Right Parts for the Job
We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.
Incoming Power Problem
Washing machine troubleshooting is one of the most common complaints that plagues appliance owners. There are many moving parts in a washing machine, and things can easily go wrong. The first thing to check when you find your Maytag washer won’t turn on is the power supply.
Do a Hard Reset
If you’ve tried everything and your washing machine is still not working, you may need a hard reset to put it back into operation.
Maytag Washer Start Button Stuck
If you need to repair your Maytag washing machine start button or any other appliance or electronic device, apply light pressure to the regions around the start button. You can also tap the areas around the button; this may help dislodge any foreign material that might be stuck between the button and make it function normally again.
Control Lock is Turned ON
Your Maytag washer has a Control Lock feature to prevent you from using it when plugged in. It may be activated by either pressing the Lock/Unlock button or pressing the Start button for three or more seconds. The Control Lock feature locks all functions to prevent an accidental start.
Incorrect Washer Settings
If your washer won’t start, there are a few things to check. If you have Delay Start activated, make sure that’s not occupying the time you wanted your cycle to run. Also, make sure your washer door is closed and that you’ve selected the right setting for your wash load.
Defective Control Board
Maytag washers typically have a user control board — also called a display board — that can be defective. The board is located on the inside top of the washer, behind the panel that has lighted buttons for functions like washing and drying. If a button isn’t responding when it’s pressed, it’s usually due to a defect on this board.
Broken Timer
The timing system of a Maytag washer is made up of timers, which control the spinning and washing functions of a machine. The timer advances the washer through its cycles until the cycle is complete.
:max_bytes(150000):strip_icc()/washing-machine-inlet-valve-56a4a2c53df78cf772835ce9.jpg)