After pulling off the trim bezel by hand (they have no screws on most models, they just pop off by pulling firmly.) you'll find a few 1/4" screws holding in the instrument cluster. Remove them and you will then be able to angle the instrument cluster out. You may need to tilt the steering wheel down and move the shifter down to make room.
Full Answer
Is there a service for the instrument cluster Panel on Silverado?
I will send my original part for repair. This is a repair and return service for Chevrolet Silverado (2003-2006) Instrument Cluster Panel (ICP) Repair, years 2003 2004 2005 2006 . When you receive your rebuilt part back from us it will be plug-n-play and not need any additional programming.
How do I remove the instrument cluster?
After pulling off the trim bezel by hand (they have no screws on most models, they just pop off by pulling firmly.) you'll find a few 1/4" screws holding in the instrument cluster. Remove them and you will then be able to angle the instrument cluster out.
Why is my instrument cluster not working?
Our rebuild and exchange service options are the easiest way to get back on the road and the ONLY way to avoid a trip to the dealership. Why Is My Cluster Not Working? These instrument clusters have a common problem with the gauges sticking, giving incorrect readings, or not working at all.
What is a repair and return service on a Chevy Silverado?
This is a Repair and Return service of your existing Chevrolet Silverado (2003-2006) Instrument Cluster Panel (ICP) Repair. This services requires that you send us your part for repair. Fast & easy process. Our service is 100% guaranteed or your money back.
How do you fix a cluster on a 2003 Chevy Silverado?
4:458:30Instrument Cluster Repair – 2003-2006 5.3L Chevy Silverado ...YouTubeStart of suggested clipEnd of suggested clipAnd off just to play it safe we're going to re-solder each resistor. Using your soldering iron meltMoreAnd off just to play it safe we're going to re-solder each resistor. Using your soldering iron melt the existing solder then add a dab of new stuff as. Well we'll do this again now for each.
Can you repair your own instrument cluster?
Replacing The Instrument Cluster Is Always The Better Option That means if you install a replacement instrument cluster the right way, you'll know that it works. You don't have that same assurance when you try to repair the cluster yourself. When you do it yourself, you don't have a way to test your instrument cluster.
How do you reset the instrument cluster on a 2003 Chevy Silverado?
Push and release the Sel/reset button button 3 times repeatedly. The instrument cluster begins its self-test. Each successive press of the Sel/reset button initiates a new cycling of all the gauges. To end, turn the ignition switch to OFF, or vehicle speed exceeds 1.5 mph.
Why did my 2003 Dashboard stop working Silverado?
These 03-06 Silverados are bad about this kind of problem, it's usually caused by failing stepper motors inside the instrument cluster. Each gauge has a motor that controls it's needle movement and when the motor goes out the gauge will either stick, jump around or die all together.
What causes instrument cluster to stop working?
Overloaded Circuit A faulty voltage regulator, which sends power to the instrument panel in most current vehicles, may be responsible for what causes the instrument cluster to stop working.
How do you fix a broken instrument cluster?
2:4513:15How to fix a broken gauge cluster - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you can just use your fingers. And just pull gently to where you break you don't want to break itMoreSo you can just use your fingers. And just pull gently to where you break you don't want to break it but you just want to separate it like this. You should come up pretty easily. There.
What are the common problems of the instrument cluster?
Some of the more common failures include:Erratic or non-functional gauges & inaccurate readings.LCD not Stuck or fluttering needles on gauges.Burned out indicator lights.Burned out/dark spot backlighting.Loss of LCD display or erratic operation (number 8 showing as 0)
Do you have to reprogram an instrument cluster?
In some newer vehicles, you may not need to do anything. The mileage will automatically show up on the new instrument cluster when you install it. It will receive the information from the computer or chip that contains it and display the mileage. In these cars, the instrument cluster is just a display.
What fuse controls the instrument cluster?
The instrument panel fuse block is located in the instrument panel, on the driver side of the vehicle. To access the fuses, open the storage compartment. Press in on the sides of the compartment to release it from the instrument panel.
Why is my dash display not working?
If the dashboard lights aren't working at all, a blown fuse may be the culprit. It's relatively easy to remove and replace a fuse that has been damaged; however, if the fuse blows again, it could be indicative of a deeper electrical problem that a professional will need to address.
Where is the dashboard fuse located?
The instrument panel fuse box is usually located inside the vehicle, and usually on the driver's side. There should be a diagram inside the fuse box (or in the owner's manual) that shows you what each fuse powers.
Can you drive your car without the instrument cluster?
Can I drive my vehicle while the instrument cluster is out for repair? Yes, you can still start and run your vehicle without the instrument cluster.
How to remove a solder cluster?
First you have to gain access to it. Use your finger to separate the clips that hold the cluster together. Pull the backside cover of the cluster off. Figure 5. Removing backside cover. Place the board in a flat surface. Begin to heat up the solder torch. Inspect the solder points for the plug connector on the board.
How to get a truck out of the way?
With the key still turned to on, pull the gear selector down to one – use the emergency brake to keep the truck in place. Grab the dashboard panel and pull it towards you. Un-clip it and pull it out of the way.
Does the Silverado 1500 have an instrumental cluster?
The first-generation Cheverolet Silverado 1500 has an un fortunate tendency for their instrumental clusters to fail. Most drivers decide to replace their clusters without realizing there is an alternative, less expensive fix.
Can solder cracks be seen?
A good connection should not have any burn marks or cracks. When you visually inspect the solder you may be able to make out the damage areas, but it should still be noted that many cracks may not be so easily seen.
Step 1: How to Remove a Chevy GM Silverado Instrument Cluster
After pulling off the trim bezel by hand (they have no screws on most models, they just pop off by pulling firmly.) you'll find a few 1/4" screws holding in the instrument cluster. Remove them and you will then be able to angle the instrument cluster out. You may need to tilt the steering wheel down and move the shifter down to make room.
Step 2: Removing the Clear Plastic Lens
Next up you'll need to remove the clear plastic lens. You'll need to use a small tool to pry out on the tabs while pulling up on the lens assembly to remove it. Work your way around one tab at a time, you can insert a pencil or similar item between the lens and the body to hold them apart while working your way around.
Step 3: Removing the Needles the Right Way
Ok now you'll need a few pieces of masking tape and a pen or marker. Rotate all the needles counter clockwise gently until the come to a stop, they should all stop at or just below the zero marks. Now make a pen mark on the tape just below the top of each needle.
Step 4: Needle Removal
Now that you've made your calibration marks firmly rotate each needle further counter clockwise a few inches. You'll be rotating the needle around the motor's shaft so there will be some resistance especially at first.
Step 5: Removing the Back Case and Circuit Board
Now pry outwards on the tabs of the back case to remove it, similar to how you removed the front lens.
Step 6: Motor De-soldering and Tools You'll Need
Ok you're now ready to remove the old gm stepper motors and replace them with new ones.
Step 7: Replacing the Old Stepper Motors With Your New Ones
Now you simply need to pop your new GM stepper motors where the old ones were, they will only install in one direction so you don't have to worry about mixing them up or getting it wrong. Make sure you get the correct part number when you buy your stepper motors (see link above for correct parts).
Description
This is a repair and return service for Chevrolet Silverado (2003-2006) Instrument Cluster Panel (ICP) Repair, years 2003 2004 2005 2006 . When you receive your rebuilt part back from us it will be plug-n-play and not need any additional programming.
Will this service fix my problems?
A full diagnostic check should first be performed to eliminate all other possible causes for your symptoms, even if the symptoms match those specified on the common fault description. If you send a good working unit because of misdiagnosis and after we test the unit and find no issue/faults, then you will only be responsible for a $39.99 testing fee and shipping. IMPORTANT! If you are not sure that this part is the cause of the fault then we recommend that you do not go ahead with this purchase and instead seek further professional advice and diagnosis..
