Here is how you fix a ball-type faucet:
- Pry off the index cover on the faucet to get to the hex-head screw.
- Use a hex-key wrench to loosen the screw and remove the faucet handle.
- Remove the cap and collar with a pair of adjustable pliers.
- Loosen the faucet cam and lift it up, including the cam washer and rotating ball.
How to fix a ball type faucet?
- With the ball removed, the valve’s seats will be visible.
- The seats are the circles themselves and the springs are located underneath the seats.
- Use a towel to soak up any water that remains in the faucet stem.
- Insert a hex wrench through a rubber seat. ...
- Repeat for the remaining seat and spring. ...
- Replace each set with new seats and springs.
How do you repair a kitchen faucet?
Method 1 Method 1 of 5: Setting up for Repair Work Download Article
- Locate the leak. Before you begin, inspect the faucet to figure out where the leak is. ...
- Turn the faucet’s water supply off. Look under your sink first. ...
- Turn the faucet on to relieve the water pressure. ...
- Cover the sink hole with a strainer to catch small parts. ...
- Label and take pictures of the faucet as you remove parts. ...
How to repair a faucet?
Loosen the Allen Screw
- Then turn off the water supply to the dripping faucet.
- Lift the handle and pry off the decorative cover to expose the Allen screw.
- Turn the screw counterclockwise until it's loose enough to lift the handle up from the stem. ...
How to replace a kitchen faucet with a single handle?
- Adjustable Wrench
- Flashlight
- Cloth
- Heavy Duty Sponge
- Plumber’s Putty
- Bucket
- Faucet Kit of your choosing
Why is my ball faucet leaking?
If the faucet leaks from the base around the bottom of the spout, this is usually caused by a worn O-ring at the bottom of the faucet body. If the faucet is leaking from the tip of the spout or aerator, then water is not being properly controlled by the lever ball or the spring-loaded rubber seals.
How do you replace a ball valve on a faucet?
1:423:23Ball Valve: Repair and Replace (Single Handle Bathroom Faucet)YouTubeStart of suggested clipEnd of suggested clipFirst install the ball valve align the pin to the slot on the side of the ball valve and slide theMoreFirst install the ball valve align the pin to the slot on the side of the ball valve and slide the valve in place the cam over top the packing and align the tab to the slot.
How do you fix a leaking single handle ball shower faucet?
0:172:38Repairing a Leaky Single Handle Tub/Shower Ball-Type FaucetYouTubeStart of suggested clipEnd of suggested clipTurn off the main water supply to your home. For an obstacle remove the index button by prying offMoreTurn off the main water supply to your home. For an obstacle remove the index button by prying off with the screwdriver. Then unscrew the handle screw. And remove the handle.
What is a ball type faucet?
Ball faucets are the first of the washerless valve types. As you can see in the picture below, they are single-handled which sits atop of a rounded base. They use springs, rubber valves, o-rings, cams, and the internal ball, which controls the temperature and the flow of water from the faucet.
How do you replace a old ball valve?
1:293:10How to Replace a Ballcock & Float Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse an adjustable wrench to grip the retaining nut found above the coupling knot. Then hold the baseMoreUse an adjustable wrench to grip the retaining nut found above the coupling knot. Then hold the base of the old floor valve inside the tank unscrew the knot under the tank.
Do ball valves wear out?
Sometimes, ball valves quit functioning because they are well past their life expectancy of eight to ten years. Sometimes ball valves give out due to corrosion that occurs in or around the ball valve. Ball valves can shut off a fixture to help control the flow of liquids or gases.
How do you take apart a single handle bathroom faucet?
1:204:00How to Replace the Seats & Springs in a Single Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the needle nose pliers to unscrew the adjusting ring. Place a cloth over top and use the channelMoreUse the needle nose pliers to unscrew the adjusting ring. Place a cloth over top and use the channel lock pliers to unscrew the cap. Now pull out the ball the cam and packing.
How does a ball faucet work?
Ball faucets have a single lever that operates a rotating, slotted metal ball. The slots in this ball align with hot and cold water inlet seats in the faucet body to regulate the amount of incoming water allowed to reach the mixing spout. Delta is one of the primary manufacturers of this faucet type.
How do you stop a dripping shower faucet?
0:002:02How to Repair a Leaky Shower Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow depending on where your leak is coming from on a shower valve typically it'll be dripping out ofMoreNow depending on where your leak is coming from on a shower valve typically it'll be dripping out of a shower head or from behind the handle. Either way you need to do the repair from the valve.
How can I tell what type of faucet I have?
To determine a faucet brand, look on the faucet for a logo or model number, which might be small and hidden around the curves of the faucet or handles. Try cleaning the faucet off first so it's easier to spot the logo or model number.
How do you fix a leaky single lever faucet?
1:123:00How to Fix A Dripping or Leaky Single Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipAdd a little plumbers grease and replace the spout put new seats on new spring. And put them back inMoreAdd a little plumbers grease and replace the spout put new seats on new spring. And put them back in place replace.
How do I know what faucet I have?
The model number is printed on a tag that is attached to the cold water supply line of the faucet. The supply line is located below the sink, countertop, bath rim, or behind the bowl of a bidet. The model number, or part number, is typically preceded by "P/N."
How do you unscrew a ball valve?
1:448:40THREADED BALL VALVE REPAIR. HOW TO TAKE APART ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see it right here on the stem located under the mounting plate you should be able to move itMoreYou can see it right here on the stem located under the mounting plate you should be able to move it and pull it off of the stem. It's made out of a PTFE material.
How do you fix a leaking ball faucet handle?
0:182:44Repairing a Leaky Single Handle Ball-Type Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere may be a button that covers the screw that needs to be removed first and then you can loosenMoreThere may be a button that covers the screw that needs to be removed first and then you can loosen the screw and remove the lever handle. Remove the retainer nut cam. And gasket. Take out the ball.
How do you replace a kitchen faucet water valve?
2:003:28HOW TO REPLACE A WATER SHUT-OFF VALVE - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the old valve removed remove. The old damaged teflon thread tape and replace it with some newMoreWith the old valve removed remove. The old damaged teflon thread tape and replace it with some new tape around the threads before screwing on the new valve.
How do I fix a single handle bathroom faucet?
0:004:37Delta Peerless Bathroom Single Handle Faucet Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just use a small slotted screwdriver and pry off the decorative cover to loosen that set screwMoreAnd just use a small slotted screwdriver and pry off the decorative cover to loosen that set screw you can use 1/8 inch allen wrench or you can get this combo tool and this has 1/8 inch allen wrench.
What is a ball faucet?
This project discusses repair ing the special type of washerless faucet known as a ball faucet. A ball faucet has a single handle that controls a special plastic or metal ball inside the faucet body. This ball has chambers or slots in it, along with rubber O-rings and spring-loaded rubber seals. As the lever is moved, the ball's position inside the faucet body controls the flow and mixture of hot and cold water coming out of the faucet. When the handle is operated, there is a distinct feeling of the ball rotating smoothly inside the body of the faucet. It is quite different from the operating "feel" of a single-handle cartridge faucet, in which you can usually feel a cartridge lifting and rotating when the handle is operated.
When did ball faucets come out?
The ball faucet was brought to market in 1954 by Delta faucet and made popular as a single lever kitchen faucet by Delta Faucet® and its DIY brand, Peerless®, starting in the 1970s. This type is also popular as a bathroom faucet. These faucets have no traditional washers that leak, but they do have spring-loaded rubber seals.
Why does my faucet leak from the bottom?
If the faucet leaks from the base around the bottom of the spout, this is usually caused by a worn O-ring at the bottom of the faucet body. If the faucet is leaking from the tip of the spout or aerator, then water is not being properly controlled by the lever ball or the spring-loaded rubber seals.
What is in a repair kit?
Repair kit contents may vary but usually include O-ring, cam, cam washer, rubber valve seats and springs and a spanner wrench for tightening the locking ring. Ace Hardware
How to determine if a faucet is leaking?
To determine the cause of the leak, you'll need to disassemble the faucet (a very simple job) and visually inspect the parts. For simplicity, you may choose to simply replace all parts rather than diagnosing the specific reason why the faucet is leaking.
Why do my faucets leak?
These faucets may begin to leak when the seals dry out, when the springs weaken, or when the rotating ball becomes cracked or acquires a mineral buildup.
How to remove knurled top cap?
Using channel-lock pliers, grip the knurled top cap and turn it counter-clockwise to remove it. (Wrapping masking tape around the upper and lower jaw of the plier can prevent damage to the cap's finish.)
Shut Off the Water
Before you can fix your single handle faucet, you'll need to shut off the water.
Remove the Cam, Packing and Ball
Remove the plastic cam, including the cam washer, the rubber packing washer and the metal ball valve assembly. Make careful note of the position of the ball when you remove it, as you'll want to return it to the same position when reassembling the faucet.
Replace Seats and Springs
Locate the valve seats. With the ball removed, the valve's seats should be visible. The seats are the circles themselves and the springs are located underneath the seats.
Reassemble the Ball Assembly
Once you've replaced the seats and springs you can begin to reassemble the ball assembly.
How to remove faucet arm from upright shaft?
Gently remove the faucet arm from the upright shaft by pulling upward on it while rotating it.
How to remove a golf ball from a socket?
Gently remove the ball. Please note the orientation of the ball, cut into one side of the ball is a slot that rides on a stud inside the socket.
How to remove a swivel aerator?
Step 1: Remove old end, aerator (looks like a cap with a little screen), or previous swivel that broke and part is still there; carefully clean the threads. Step 2: Use one layer of Teflon tape around the outer threads. Converter first, then swivel. Hand tighten to be very snug, and do not wrench.
How to fix Allen wrench that won't remove?
Spray it with PB Blaster and let set, then spray again. Make sure the Allen wrench is secure and turn outwards to the left. If you still can't remove it, then replace it.
How to check for leaks in water valves?
Turn on the water at the valves and check for leaks. Start out with the water on cold and on with about half the maximum pressure. If things look OK with the half pressure then turn the cold water on all the way. Again, check for leaks. Once you're sure things are OK, turn on the hot water. ...
Where to get replacement water cartridges?
You can get the replacement cartridge from any big box hardware store.
Can you force a ball into a socket?
Replace the ball into the socket keeping the alignment of the ball in mind. You shouldn't have to force the ball into the socket.
