Repair minor breaks and splits within the basket's weaves with wood glue. Apply a dab of wood glue to the flat end of a toothpick, spreading the glue over one end of the damaged fiber, then pressing the material back into place.
Full Answer
How do you weave a chair?
Turn your chair back to the top and start your second row by weaving OVER 1 then under 2, over 2, under 2, over 2, etc. until you reach the other side. Photo shows top of chair seat. Pull your reed snug and position the second row of weaving to touch the first row. Do your best to keep the weft at right angles to the warp.
Can I reweave the seats of my wicker chairs?
If you’d like to reweave the seats of your chairs and need the materials to do so, please visit the suppliers on the National Cane & Basket Supplies Directory™ page, since The Wicker Woman® does not sell supplies to the general public.
What is chair caning or rush seat weaving?
Chair caning, rush seat weaving, and splint woven seats are all terms for specific designs and techniques used in the process of weaving a chair seat.
How do you fix a broken reed chair?
Remove the old chair seat; clean the chair and sand if needed. Repair any broken rungs and apply the finish of your choice. Open your bundle of reed and select the longest pieces. Before using each piece, soak in warm water for 2 to 3 minutes--this is usually long enough to make reed flexible.
How do you fix a basket weave chair?
Use wood glue to fix them. Apply a drop or 2 of wood glue to the bottom of any loose ends that are sticking out. Carefully tuck them back into the wicker pattern by pulling the strands together. Hold down the glued pieces for several seconds to allow them to bond to the chair.
How do you fix a woven patio chair?
How to Fix Faux Wicker Patio FurnitureClean the Faux Wicker Patio Furniture. ... Remove Broken and Frayed Ends. ... Cut a New Resin Strip to Fit. ... Apply a Quick-Set or Non-Quick-Set Epoxy. ... Weave the Strip Into Place. ... Glue the Ends Together Before Trimming. ... Touch Up the Section as Necessary.
How do you fix a wicker chair seat?
Apply a dab of wood glue to breaks in the fibers, using the flat end of a toothpick as an applicator. Press the broken fibers back together for a moment, then allow them to dry completely. Apply glue to the ends of fibers that have come away from the frame, then push them back into place with a toothpick.
How do you repair wicker furniture?
Steps to Repair Wicker FurnitureClean the wicker. ... Next, check for any loose ends. ... Check for loose wrapping. ... If you need to replace any broken pieces, the first thing you'll want to do is soak your replacement wicker fibers. ... Remove the broken piece of reed by cutting each end.More items...•
Can you repair resin wicker furniture?
If the resin strips are loose, you can reattach them with glue. You can use resin epoxy. Dip the tip of the strip in the epoxy and hold it in the weave for a few seconds. If the strips are cut or frayed, you will need to repair them differently.
What's the difference between rattan and wicker?
“The difference is that rattan is a material, whereas wicker is the style and method of weaving,” Zoe explains. “Wicker can be woven from rattan as well as many other natural or synthetic materials, which is where the confusion often lies.”
How do you Recane a chair seat without a spline?
4:4713:10Installing Pressed Cane with no Spline - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd that takes a little practice and a little time and then I'm going to put. This this rail in toMoreAnd that takes a little practice and a little time and then I'm going to put. This this rail in to hold. It. It's kind of hard to do because the cane makes it tight.
How do you fix a broken chair seat?
6:147:23How to Fix a Wooden Chair Seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipMaking sure you've got full coverage reassemble clamp the pieces. And clean up the glue. And lastlyMoreMaking sure you've got full coverage reassemble clamp the pieces. And clean up the glue. And lastly touch up any fish or required.
How do you repair a cracked resin chair?
0:284:53How to Fix broken plastic chair in 4 minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo first things first is to apply hot glue like you saw i just did so and attach it to you know backMoreSo first things first is to apply hot glue like you saw i just did so and attach it to you know back to the base of the chair. So i just apply the hot glue around the surface.
How do you restore outdoor wicker furniture?
1:133:33How to Restore Outdoor Wicker Furniture - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemove all cushions from your wicker chairs and sofas using a garden hose wash down the tops of allMoreRemove all cushions from your wicker chairs and sofas using a garden hose wash down the tops of all pieces. Turn the pieces over and wash down their undersides remove as much paint as possible.
Can rattan chairs be repaired?
Not to worry—both wooden and synthetic rattan are easy to repair, and both can be fixed in the same way. If your furniture only has a few loose ends or wrappings, refer to the first method in this guide. If some sections of your furniture need a little extra TLC, skip ahead to the second method.
What material is wicker?
Natural wicker is made from a variety of vines, grasses, and plants. Wicker furniture is sometimes referred to as rattan furniture, but wicker and rattan are not the same things technically. The rattan plant is a commonly used material for wicker furniture.
How do you fix an outside webbing chair?
0:044:25How to Replace Outdoor Sling Chair Fabric with Phifertex - YouTubeYouTubeStart of suggested clipEnd of suggested clipNot all chairs have the same width at the top and the bottom so you may have to cut your piece at anMoreNot all chairs have the same width at the top and the bottom so you may have to cut your piece at an angle. Add one inch to each side for seam allowance and to make channels for the spline.
How do you repair lawn chairs with webbing?
1:324:14Re-Web a Lawn Chair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm going to take the webbing fold it over like that put the clip. Into the hole. And bring itMoreAnd I'm going to take the webbing fold it over like that put the clip. Into the hole. And bring it tight around the front keeping this tight I'm going to weave it through the old webbing.
How do you fix a rattan chair back?
0:544:26How to Replace Pressed Cane Webbing - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest way to get the spline out of the groove is to use a caning chisel but you can also useMoreThe easiest way to get the spline out of the groove is to use a caning chisel but you can also use an appropriately-sized chisel or screwdriver. Cut out the middle of the cane.
How do you fix ripped patio furniture?
1:382:45How to fix ripped patio furniture - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo on this what i did is i took the measurement. And i cut two pieces at a time and then i added aMoreSo on this what i did is i took the measurement. And i cut two pieces at a time and then i added a quarter inch each time and that seemed to work out really well for this.
Where to lay on baskets?
Lay on piece along the top and the other along the underside of the handle from one side of the basket to the other side.
Where to place new ribs?
Place the new rib alongside the old rib.
How to replace a broken basket?
Fill in holes such as punctures with reed or caning of the same size, shape and color. Trim the damaged ends of broken fibers close to the basket so they are no longer noticeable. Cut fresh pieces of replacement material large enough to span each missing strand with a little leftover to tuck into the weave. Weave the new material under and over existing strands, using a toothpick to help guide the pieces in place. Tuck the ends into the existing weave to keep them in place; use a dab of glue for added support.
How to repair a broken basket handle?
Apply a dab of wood glue to the flat end of a toothpick, spreading the glue over one end of the damaged fiber , then pressing the material back into place. Press down for a moment or two to ensure the glue holds, or use a binder clip or clothespin as a clamp until the glue dries. Split material in the handle can be repaired in the same fashion.
How to get rid of mold on wicker basket?
Apply a 50:50 solution of bleach and water to visible mold spots using a cotton swab, then allow the basket to air-dry completely. Before application, first test an inconspicuous area such as the basket bottom to ensure the bleach does not discolor the wicker.
How long do wicker baskets last?
Wicker baskets, under proper care, can last for many decades or even generations. The natural materials used to weave these baskets, such as rattan reed, may become brittle and break under heavy use or continual exposure to dry heat. Some wicker basket repairs can be done at home without professional assistance;
What to do if a basket is falling apart?
If the basket is valuable or falling apart completely, a professional repair may be necessary to avoid additional damage or loss in value. If a lot of mold is on the basket, wear a dust mask while cleaning it to avoid breathing in fine airborne particles. Writer Bio.
How to clean a basket that smells musty?
Take the basket outdoors if it smells musty or if you notice specks of mold or mildew. Clean the basket with a feather duster or soft brush to remove dust and some of the mildew or mold. Vacuum the basket gently if you feel more cleaning is necessary , using an upholstery brush attachment.
How to weave a reed?
Its important to remember two things: 1 You will need more length than the linear distance between start and finish of your weave because the weaving action takes up more reed than you might otherwise expect. 2 Leave at least an additional 2 inches excess at the end of each side of the new reed so that it can’t pull out the you put the finished ends tucked under the surface where they can’t be seen.
What material is used to replace wicker reeds?
Wicker can be manufactured using natural or synthetic resin materials. Whether you use natural or resin reed, the style and size of the reed can vary and so can the colors. 3.
How to keep a reed in place?
Back out the end of the remaining reed so that the end is aiming down away from the surface. Leave at least 1-2 inches of the original reed tucked down under the surface. To keep a piece of reed in place properly, the more you weave it in the better it holds. So, if you can, try to remove enough original reed so that you can weave back in a pice over and under the cross members at least four to seven times, more if you like. In small areas you may have no other choice but to use a short weave over and under 2-3 cross members. In those cases, you might have to live with it being a little loose when you weave the new piece in. But its perfectly acceptable as long as the woven piece does not fall out.
Why do you need more length than the linear distance between start and finish of your weave?
You will need more length than the linear distance between start and finish of your weave because the weaving action takes up more reed than you might otherwise expect.
How long do you soak wicker reeds in water?
Note: Natural wicker reed will need to be soaked in water for at least 15 minutes to make it flexible enough to bend prior to weaving. 10. Stain and Seal Natural Wicker. If you are repairing a natural wicker product, you will need to stain or paint it to match your finish.
How to get a replacement reed?
In order to acquire the correct replacement reed, you might need to take a sample from the damaged reed or from a piece of reed that has excess sticking out from a concealed place under the furniture. If you can acquire a sample you can show the vendor, you have a better chance of getting the right replacement or one close enough you can live with from them.
Is it hard to repair wicker furniture?
Repairing wicker furniture sounds hard and in some cases it can be. However, this lesson concentrates on replacing missing or damaged reed that is woven in one direction and not intended for highly complicated woven sections. Small repairs are very easy and doing it yourself can be a very rewarding experience. Once you get the feel for it, it’s not bad at all and it does however, take a little patience.
What is chair seat weaving?
Chair caning, rush seat weaving, and splint woven seats are all terms for specific designs and techniques used in the process of weaving a chair seat. This weaving process goes by many names, chair seat weaving, wicker, chair seating and seatweaving to name a few. However, most people lump it all together ...
How are chair seats woven?
This age-old chair seat weaving method is woven by hand with individual strands of cane. These strands go through holes that are drilled in the perimeter of the seat, creating the familiar octagon (8-sided), pattern.
What is chair caning?
However, most people lump it all together including the woven seat pattern and material, and the act of weaving itself, so it all becomes “chair caning.”. Actually, the term “chair seat weaving” encompasses many different types of weaving techniques, patterns, designs, and weaving materials. With chair caning itself being only one type ...
How many steps are there in caning a chair?
Many different gauges of cane are used to suit the design of the chair and size of the drilled holes, but all woven in the same 7-step pattern. The 7-step method of hand chair caning is tedious and time-consuming to weave, but a lovely, strong, and durable pattern when completed. There are also many other designs that can be woven through ...
What is a caned chair?
Hole-to-Hole Chair Caning –is the traditional and most well-known of the seat weaving designs and patterns. Hand caned seats have a lacey, open weave pattern and a row of holes drilled around the perimeter of the seat and/or back.
What material is used for Danish chairs?
Another material frequently used in weaving Danish Modern chair seats is wide binding cane in either 4, 5 or 6 MM. Cane is woven on both the seat and back, in various patterns but only around the frame and not through drilled holes or put in a groove.
What is Danish modern seat weaving?
Danish Modern Seatweaving –typically uses a 2-ply laced Danish cord and is looped around “L” shaped nails on the inner framework, woven in a special basket weave design.
How to prevent scratching on chair?
By flattening the points you'll prevent scratching or cutting yourself later. Continue warping your seat from front to back splicing when needed. Keep all of your splices on the underside of your chair and stagger the splices at various distances from the front rail.
How to weave a warp piece?
Starting on the right side, weave over the rung then weave over 2, under 2, over 2, etc. across the bottom warp pieces.
How to wrap a reed on a car?
Starting from the left side of your seat, wrap the reed UNDER then over the front rung. The smooth side of the reed will be facing outward.
How to tie a reed knot?
To tie the knot wrap the end of the reed under and around the rung, then under the reed and back through the loop so the end of the reed lays against the rung. Tighten the knot and trim any excess.
How to make a reed flexible?
Open your bundle of reed and select the longest pieces. Before using each piece, soak in warm water for 2 to 3 minutes--this is usually long enough to make reed flexible. Flat reed has a smooth side and a rough side. We want the smooth side of the reed to face outward.
What is warp in chair seat?
The warp of your chair seat wraps front to back.
What is a flat reed chair?
Flat reed is inexpensive, makes a strong chair seat and will last for years. NOTE: You may also use these instructions when re-bottoming your antique chair seat with Paper Splint - a flat brown paper product that has been used for chair seats for many years.
How to paint a chair with old wood?
Sand your chair as needed to remove old finish and any rough spots. Apply polyurethane as I did on the chair above or use paint to add more color. Chalk paint is a great option for old wood as it requires less prep and bonds well (blue chair).
What is paracord chair?
Paracord is short for parachute cord which was it's original use. It's now available in a multitude of colors and has a million uses. Comprised of multiple nylon cords it's amazingly strong, very durable, and easy to clean. Cost is not prohibitive either as repairing a chair costs approximately $25. Paracord woven chairs wear well and will look ...
How does a clove hitch work?
After cinching the clove hitch knot rotate it 180 to hide the crossing strand. The clove hitch starts you off with 2 turns in the front which is convenient when you are trying to add extra turns along the front.
How to find extra turns on a dowel?
This is the number of extra turns you need to make up on the left and right side of the front dowel so the center will be straight. Turns (front) - Turns (back) = Extra Turns to be made on Front. Extra Turns / 2 = Extra Turns on Left and Right sides of front dowel.
How many turns does a yellow chair have?
Example: On this yellow chair the front had 85 turns and the back 69 turns so I needed to account for a 16 turn difference. Dividing by 2 meant 8 extra turns on each side of the front were needed for the center to be straight.
Can you find old wooden chairs with broken bottoms?
It's fairly easy to find old wooden chairs with broken out seat bottoms. Often the chair frame is solid, but no one i
Can you add more cord on the bottom side?
You can always add more cord on the bottom side so it's not critical to be exact. First.... First find out how many turns you'll be making on each side. In essence of time, I suggest wrapping around and around the entire length of the back dowel, front dowel and one side to get an accurate count of turns.
How to epoxy a weave?
With the help of a paintbrush, apply the epoxy in the empty space and insert the new strip in the weave. Lastly, connect the strips to the epoxy.
How Can I Repair a Resin Wicker?
To repair your resin wicker furniture, you will need a few tools. You will need new resin wicker strips, manicure scissors or box cutter, and plastic epoxy. Optionally, you will want to match the wicker color with matching paint or spray paint.
Why is plastic wicker furniture durable?
Plastic wicker furniture lasts for a long time because they are durable and weather resistant. If you clean the furniture regularly, it will give you a nice look that outlasts regular wicker furniture. Another benefit is that it is lightweight, making the furniture, like plastic rattan tables and chairs, easy to move.
What to do if resin strips are loose?
If the resin strips are loose, you can reattach them with glue. You can use resin epoxy.
How to insert a new strip?
To insert a new strip, you will need a resin epoxy. Take a small paintbrush and paint the empty space of the pattern.
How to match furniture color?
Try to match your furniture’s color or you will have to do a touchup with matching paint. Then, you will need a pair of needle-nose pliers. For the finishing touch, you will need a paintbrush and a similar colored paint. Spray paint will also do the job to match your color or redo the color of your furniture.
What are the benefits of rattan furniture?
Another benefit is that it is lightweight, making the furniture, like plastic rattan tables and chairs, easy to move.
FREE Chair Caning Instructions
Here are helpful and FREE chair caning instructions on how-to cane chair seats by hand, lace or strand | Read more…
FREE How-to Install Cane Webbing
Installing cane webbing is a lot easier and less time consuming than its counterpart, hole-to-hole hand caning.. | Read more…
FREE How-to Paint Wicker Furniture
If you own wicker furniture, at some time or another you might want to know how-to paint wicker furniture to help prolong its life. | Read more…
FREE How-to Care for Wicker Baskets
Extend the useful life of your baskets by following these simple how-to care for wicker basket tips and hints. | Read more…