
Bike Tube Repair
- The Necessary. All you need is a pump and a repairing kit. ...
- Inflate. First thing to do: find the hole. This could be simple or pretty long. ...
- Blblblbbl. To find the tiny holes inflate the tube. ...
- Mark. Make the mark twice as big as the patch with an "X" through the center of the hole, it allows for spreading out glue if too much ...
- Scratch. With the help of sandpaper or grater scratch the rubber all around the hole, this will help the mastic to adhere to the tube.
- Mastic. Time to spread the right amount of mastic on a surface a little wider than the patch. ...
- Patch. The patches have a metal cover on the glue side, and a plastic foil on the other one. ...
- Strip. To remove the thin plastic sheet you have to keep down the patch red border with your nail. ...
- Inflate Again. Otherwise this is probably your reserve tube, you are at home fixing it meanwhile you relax your limbs after an hard riding morning, and you can ...
- Deflate and Roll Up. Now deflate (this is the tedious part), roll up the tube and hold it with an elastic. ...
How to fix a bicycle tube without a patch kit?
Tools needed to fix inner tube without patches
- Tyre levers
- Mini pump
- Zip ties
How to change an inner tube on a bike?
The 3 Things You Need To Change A Bike Inner Tube
- Tire Levers Tire levers are a cheap but vital tool that every cyclist should own. ...
- Bike Pump Hand pumps are fine for mountain bikes, but for the higher pressures used in road bike tires, it’s best to use a track pump (the type that ...
- A New Inner Tube
How to replace a bicycle tube?
How to replace a blown inner tube on a bike? Steps Prepare a travel bag containing all of the tools and equipment necessary to replace a blown inner tube. Detach the wheel with the blown inner tube using a wrench or your wheel鈥檚 quick release lever. Remove the tire from the rim once the wheel is detached from the bike using a tire lever.
How to fix bike inner tube near valve easy?
Things to carry on any ride
- Tyre levers
- Two (or more!) spare inner tubes
- Patches/repair kit
- Some bits of old tyre to reinforce big holes
- A pump
- A mobile phone: if all else fails, get a lift home before hypothermia sets in

How do you fix a bike tube at home?
0:131:16How to Fix a Bike Flat without a Patch Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep 3 wrap the strap from your sunglasses. Around the hole in the tube like a tourniquet tying.MoreStep 3 wrap the strap from your sunglasses. Around the hole in the tube like a tourniquet tying. Several knots around and next to the hole to create an airtight seal.
Is it worth patching a bike tube?
Overall, patching is cheaper and better for the environment than replacing your tube, so I recommend it for most situations. However, there are some flats that cannot be patched. If the hole is near the valve stem or if it is a linear tear and not a hole, you will need to swap tubes.
Can you repair bike tubes with duct tape?
Patching Inner Tubes with Duct Tape You can use duct tape to cover the hole and at least go down the road for a short distance. If there's no puncture repair kit in sight, use some more tape to cover up your hole until you have time to fix it properly.
How do you fix a puncture on a bike tube?
1:132:26How To Repair a Bicycle Puncture - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the sandpaper from the puncture repair kit and roughen the surface of the inner tube. ThenMoreTake the sandpaper from the puncture repair kit and roughen the surface of the inner tube. Then apply the rubber solution and blow on it to speed up the drying. Process.
How long can you ride on a patched bike tube?
Standard glue patches last pretty much indefinitely if applied correctly. They can be a pain to apply on the trail, but I've had them last over a year. I have 5 or so of the park glueless patches on one tube, some of which have been on there for months.
Can you use super glue to patch a bike tire?
In summary, super glue cannot be utilized to patch or repair a puncture in tires or their associated inner tubes by its very nature. Cyanoacrylate gum or super blue often gets dry, brittle, and inflexible after prolonged exposure to air. For this reason, it is simply not appropriate for tire mending.
Does Gorilla tape work on bike tubes?
The mechanics I've spoken with say it works great and no failures. Best of all - it's cheap! It's available at most hardware stores, usually in the duct tape section. It comes in several widths but is easy to tear or cut to the desired width - which is good because not many bikes have 1-7/8" or 3" width rims.
Will Gorilla glue fix a puncture?
Introduction: Instant Puncture Fix Whereas with using gorilla tape you just find the puncture and put a bit of tape over it and off you go. Its that simple! It reduces the time taken to fix a puncture from 15 to 30 minutes to about 5 (depending on how fast you can find the puncture).
Can Flex Seal fix a bike tire?
Flex Seal spray contains toluene a solvent powerful enough to turn shoe rubber into eraser like paste and it makes sense that this toluene would also dissolve bicycle paint and destroy tires.
How do you patch an inner tube?
0:382:06How to Patch a Bicycle Inner Tube - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse your thumbnail or a coin to press the patch into the glue rubbing firmly inflate the new tubeMoreUse your thumbnail or a coin to press the patch into the glue rubbing firmly inflate the new tube with your pump until it takes a round shape.
How do you make a homemade tire patch?
5:339:35DIY Cheap + Easy Trick For A Flat Tire Repair. Never Be Left Stranded ...YouTubeStart of suggested clipEnd of suggested clipNext up and what you want to do you take your rubber cement that comes with your tyre plugin kit andMoreNext up and what you want to do you take your rubber cement that comes with your tyre plugin kit and you're gonna put some on. There.
Can you patch a hole in a bike tire?
2:134:03How To Fix A Bicycle Hole - YouTubeYouTubeStart of suggested clipEnd of suggested clipGreat some chalk using the grater on the back of the repair kit and liberally spread over the patch.MoreGreat some chalk using the grater on the back of the repair kit and liberally spread over the patch. This will soak up any extra glue and stop it sticking to the inside of the tire.
Do I need a new bike tire or just a tube?
As long as it is a pin sized nail and not a rail road tie then you should be just fine replacing the tube and still using the tire. Just be sure the pin is not still in the tire ready to flat another tube. If its just a puncture, learn to patch the tube.
How many times can you patch a bike tube?
A properly patched area of a tube is stronger than intact tube area. Never patch a tube more than 3 times.
Can road bike tubes be patched?
Typically the old style patch kits work better than the pre glued ones, but properly applied ones should hold up. Follow the directions in the patch kit to apply it properly. Check for things on the inside of the tire (or outside) or canvas showing.
Do I need to replace my bike tire after a puncture?
Generally, if you are using an inner tube in the tire, you should replace the tire if there is more than a 2 millimeter cut in the tire casing. Not in the rubber, mind, but it the threaded cloth casing that your rubber bits are laid on to.
Where to find tube size on bike?
Tube size information should be on the sidewall of your tire; it should also be listed in your bike owner's manual. Some riders will use a patch as a field repair, then they replace the patched tube with a new tube at home.
How to patch a tire tube?
Here are the typical steps for patching a tire tube: Grab your supplies: At a minimum, that’s a patch kit and tire levers for removing the tube from the tire. Find the leak: Closely check the tube; tiny holes require detective work or submersion in water to locate.
How to check if bike tire has lost air?
One final check: Leave the tube out overnight, too, and check the next morning to see if it’s lost any air. If not, you’re ready to insert the partially inflated tube back into the tire. Then it’s a matter of reseating the tire onto the rim, fully inflating it and putting the wheel back on the bike.
How to check for a tube leak on a tire?
If no outer tire wounds point you toward the tube leak, then check the thin strip along the inside of your rim. Look for protruding spoke ends or areas where the strip may be distorted, allowing the tube to get pinched against a spoke-hole opening.
Can a severely damaged tube be saved?
Decide whether to repair or replace: Severely damaged tubes can’t be saved.
Can you repair a tube valve?
Any time a tube’s valve is damaged, even at the base, then it’s definitely not repairable. In a borderline case, you can try a patch and let its success or failure dictate a full tube replacement. It’s wise to carry a spare tube when you ride.
How to feed a new tube to a tire?
Feed the new tube between the outer tire and wheel rim. Start at the valve stem and feed it through the hole in the rim. If the valve stem has a lock ring, tighten it by hand to secure the stem in place. Then, methodically push the new tube into the gap all the away around the wheel.
How to unlatch a bike brake?
In many cases, you’ll simply have to unlatch a quick release located on either the brake calipers or the brake lever on the handlebars. Or, you may need to squeeze the brake calipers together in order to detach the brake cable from them.
How to get tire out of rim?
Pry out a section of the outer tire with two simple levers. If possible, avoid metal tools and use a plastic tire lever instead. Feed one lever between the outer tire and wheel rim, and pop out a section of tire — instead of sitting in a channel on the inside of the rim, it should now be off the rim in this spot. Leave this tire lever in place.
How to remove bike wheel?
Loosen the nuts that attach the wheel axle to the bike. You don’t need to remove the nuts completely, just loosen them enough that the wheel can (a few steps from now) be pulled free. If the nuts don’t want to budge when you use a wrench on them, apply a lubricant like silicone spray or even cooking spray. If you have a modern bike with quick-release wheel latches, taking the wheel off will be even easier — just open the latch and loosen the nut by turning it a few times so it can clear the frame. Don’t remove the wheel yet.
How to deflate a tire with a presta valve?
For a Presta valve, unscrew the top part of the stem to release the air. With a Dunlop valve, loosen the cap a few turns and then pull on the valve tip.
How to get a valve stem out of a tire?
Pull the tube out from between the outer tire and wheel rim. Reach into the opening you’ve created with the levers and grab onto the rubber tube inside. Work your way around the wheel and pull it out completely. When you get to the valve stem, push it down through the rim and pull it free with the tube.
What do you use to make a lever on a car?
A pair of spoon handles or flathead screwdrivers will work as levers, but you have to insert and pry with them carefully so you don’t scratch up or bend your wheel frame.
How to inflate a bicycle tube?
Replace the tube without damaging it: Minimally inflate the bicycle tube. With a good bicycle hand pump 1, 2 or 3 air blasts are enough. Carefully reinsert the inner tube under the tube between the shell and the wheel. Tighten the fixing ring on the bicycle valve. Press the mantle back into the bicycle wheel. Be extra careful with this. This work can be very fiddly. Sometimes you will need strength to do this and will need to use a tire lever to help. Once the tyre is firmly seated in the rim of the wheel, you can reattach the fixing ring to the inner tube. Now you can fully inflate the bicycle tube.
Who makes bicycle inner tubes?
When it comes to bicycle inner tubes, tubes from the Schwalbe company have proven themselves over the years.
How to patch a bicycle tire?
Apply patch to hole & press firmly: Apply the bicycle tire patch to the adhesive. Then squeeze it really tight! In order to press the bicycle tire patch properly, you can use a bicycle tire lever. Alternatively, some patches already have an integrated aid. You can apply the patch particularly firmly and reliably if you place the tube on a round object. A water bottle or a bicycle water bottle is particularly suitable.
How to remove a bicycle tire from a bike?
Remove the bicycle tire from the bike: The bicycle tire must be removed from the wheel on one side. This works with a tire jack. Only with one side removed bike tire you can get to the tube. First, completely deflate the bike from the bike tire. Rake the tire lever between the wheel and the casing. On the opposite side to the bike valve works best. You are allowed to work with a little pressure. You can detach the bicycle casing from the wheel with a lever movement.
How to find a broken hose in a water bath?
Broken hose in water bath: Despite all your efforts, you can’t find the spot with the hole? Fill a bucket or small tub with water. Immerse the hose completely or partially in the water bath. If the place with the hole is under water, you will see the air escaping in the form of air bubbles.
Do you need a pump to inflate a bike tube?
To inflate the patched tube, you will need an approved bicycle pump. High quality bicycle floor pumps fit all bicycle valves. Bicycle hand pumps are usually compatible with 2 of the 3 bicycle valve types.
Do you have to change the inner tube of a bicycle?
A bicycle inner tube has a very long service life. Therefore, you do not have to change the bicycle tube regularly. A change is only recommended in the event of a flat tire. Over time, a bicycle inner tube also becomes porous. This increases the probability of a defect. However, we are talking about a point in time over several years. Even though modern bicycle inner tubes are very reliable: you will probably get a flat tire within this time and have to patch the bicycle inner tube or replace it. In the case of a replacement, the service life starts all over again anyway.
How to replace a tire tube on a bike?
If one of your wheels needs its tube replaced, remove the entire wheel from your bike , deflate the tire, and pull out the tube. You will need a tire lever, which is a small, mostly flat, plastic tool with a curved end. The tire lever will allow you to hook the bead, which is a thin wire cable embedded in the bottom of the tire that helps to seal the tire to the wheel.
How to fix a broken bike chain?
Fixing a broken bike chain requires a chain tool—a compact, universal multi-tool. Once you have your chain tool on hand , flip your bike upside down so that its wheels face up and it is resting on the seat and handlebars. Examine your chain and determine which end needs to be removed.
How to inflate a bike tire?
Starting at a point next to the valve, push the tire bead inside the rim, and proceed along the entire wheel. The tire bead is the edge of a tire that sits on the wheel. Once the wheel and tube are on the wheel, inflate your tire slowly. As you inflate, make sure that the tire bead remains in place and that the valve stays straight. It is helpful to first inflate to 10-15 PSI, then go around the tire rocking it slightly back and forth. This will help the bead seat in its proper location. Finally, reinstall the bike wheel.
How to inflate a tire that is round?
Once you are sure the tire is safe, take your new tube and inflate it until it is round in shape and confirm it holds air. Line up the valve of the tire and valve stem of your tube, then place the tube inside of the tire.
How to pull a tire off a rim?
Pull the tire to one side at the point completely opposite the valve, and try to hook the bead from underneath. Once hooked, you can slide the lever radially around the tire to pull it over the rim. Once one entire side is off, pull the other side off in the same direction. For large tires, this will be pretty easy, and it might be a bit difficult for smaller ones. You can pull the tube out from just one side at this stage to give yourself some more room to work with.
How to get a slipped chain back on a bike?
Pick up the slipped chain and position it to the top of the correct gear while pedaling. Once the chain teeth are locked in place, slowly release the derailleur and push the pedal forward to move the back wheel. Continue pedaling until the rest of the chains are fit back into their original positions. Before you get back on your bike, shift to the lowest gear and continue pedaling. This movement should realign your chain and lock it back into place. Changing gears without pedaling can cause the chain to bind up, and should be avoided.
How to replace a spoke on a broken wheel?
Begin by removing the wheel and tire. Move the rim tape to one side. From there, unscrew one side of your broken spoke from the rim. Remove the other end of the spoke by sliding it through the hub eyelet.
