how to repair a broken sprinkler line

1. Use a hand trowel to dig up the area above the sprinkler line. A shovel can break the sprinkler system even further.
2. Cut a square patch with a shovel over the break if the line is buried. ...
3. Remove the patch with 2–3 inches (5.1–7.6 cm) of dirt on the roots. ...
4. Dig carefully around the sprinkler line to expose it. Once you’ve remove the patch of grass, you will be left with a clean square of earth above the break ...
5. Clean off the section of exposed pipe with a wet cloth. ...

Full Answer

How to fix an underground broken sprinkler pipe?

Steps

1. Ensure you have all the required supplies. Nothing is worse than having to run to the hardware store in the middle of a project.
2. Find the rupture. Usually a soggy area of grass, but sometimes it is a geyser.
3. Turn off the sprinklers, if you don’t this could be a very hard task.
4. Dig up the pipe. ...
5. Cut the pipe. ...

More items...

How do you repair a leaking sprinkler pipe?

• Unscrew the coupling nut joining the P trap with the pipe draining from the sink. ...
• Following the manufacturer’s instructions, wrap a length of plumbers tape around the threads of the pipe.
• Move the P trap back into position with the draining pipe and reconnect the pipes with the coupling nut. ...
• Run water to check if the seal holds.

How to fix a broken or rusted exhaust flange easily?

Method 1 Method 1 of 3: Locating an Exhaust Leak

1. Park the vehicle on a level surface. In order to repair an exhaust leak, you will need to jack the vehicle up to locate it.
2. Wait for the exhaust to cool. You won’t be able to work on the exhaust pipe of your vehicle until it has cooled down for a while.
3. Jack the vehicle up. ...
4. Inspect the exhaust piping. ...
5. Start the engine to help locate leaks. ...

More items...

How to quickly fix a leaking brake line?

Method 5 of 6: Replacing the Master Cylinder

1. Open the hood and locate the master cylinder.
2. Remove the brake fluid reservoir cap.
3. Withdraw brake fluid from the master cylinder using a turkey baster. ...
4. Disconnect all electrical connectors from the master cylinder.
5. Disconnect the brake lines using a line wrench by turning the line wrench in a counterclockwise motion.

More items...

How do you repair a break in a sprinkler line?

First, find the leak by looking for escaping water or sprinkler heads with little to no flow. Then, dig up and expose the damaged pipe so you can remove it. Use a slip coupling to replace the damaged section of pipe, fill in the dirt around it, and you're done!

Can you patch a punctured sprinkler line?

2:024:32Howto: fix a puncture in your sprinkler system - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically I just use this this tool here you can use whatever you can use a razor blade you cutMoreBut basically I just use this this tool here you can use whatever you can use a razor blade you cut it cut it right at the the crack.

How do you fix a broken sprinkler pipe under concrete?

0:121:33EASILY Repair Broken PVC Irrigation Pipes (UNDER CONCRETE)YouTubeStart of suggested clipEnd of suggested clipIn so this was really easy i put the shark bed on i twisted this on and now i can literally flexMoreIn so this was really easy i put the shark bed on i twisted this on and now i can literally flex that on put pvc glue on that and collar. Done.

How do you fix a broken PVC pipe outside?

1:162:33How to Fix Broken PVC Pipe Leak - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the outside of that pipe with something like this which is the Christie's purple primer. AndMoreAnd the outside of that pipe with something like this which is the Christie's purple primer. And then we'll apply a wet and dry glue. So the glue I've got here is a quick repair or a quick set glue.

How to stop water from pouring out of pipe?

Clean the pipe. Some water will come pouring out at first, you could try to catch it, but it is easier to bail it out. Once the water stops coming out, clean both ends with a rag. ...

How long should a PVC pipe be?

Or you can buy a PVC fitting from most home improvement stores that has one pipe sliding inside an outer barrel with an O-ring inside. It will extend almost 3" in length. You may see in stores 1/2" to 2 1/2" in diameter sizes.

Step 1: The Materials for the Job

The first step of any DIY plumbing renovation is gathering the materials and tools you need to handle the task at hand; this applies to broken sprinkler head repair, just as it does for replacing a faucet or installing a new shower head.

Step 2: Clearing the Area and Accessing the Sprinkler

With shovel or trowel in hand, start careful digging around the sprinkler head in question. When digging, leave enough room for your hands to reach the entire sprinkler head unit, as well as the riser (the pipe segment connecting the head to the irrigation line). You should only have to dig around 6-8” to access the whole sprinkler unit.

Step 3: Removing the Sprinkler or Line

Now that you have access to your sprinkler and irrigation line riser, determine whether the task requires replacing just the sprinkler unit, or the irrigation line as well. If the irrigation line is severely broken or faulty, you may want to contact a plumbing specialist to deal with the problem.

Step 4: Replace the Sprinkler Head and Riser

For sprinklers without pop-up head features, you may have to cut out the riser connecting your sprinkler to the irrigation system (this is where that trusty handsaw or pipe cutter comes into play). Attach a threaded tee fitting to the existing pipe, and a male coupler onto the tee fitting once it’s in place.

Step 5: Filling in the Gap

Once the glue has hardened, you can refill the initial hole and attach the spray nozzle to your replacement sprinkler head. Make sure the dirt is compact, to keep the new sprinkler in place and level with other units.