Cleaning the park with a wire brush to remove dirt or corrosion may allow a connection that restores the trimmer to working order. If that doesn’t work, then simply pull off the spark plug cover and remove the old spark plug. Replace the spark plug as well as the spark plug cover. Then try starting the trimmer again. Other Malfunctions
Full Answer
How to restring DeWalt 20V Trimmer?
- Age 55 to 64
- Trade Advanced DIY
- Experience Advanced Do It Yourself (DIY)
How to tune up a craftsman weed wacker?
How to tune up a grass line trimmer video
- Supplies you might need. Only two parts are needed to do the tune-up: a spark plug and an air filter cover. ...
- Before you start. Be sure there are no open flames or ignition source in the area, because you're working with fuel.
- Drain the fuel. ...
- Replace the spark plug. ...
- Clean or replace the air filter. ...
- Lubricate and refuel. ...
How to restring your Trimmer?
Method 1 of 3: Changing the Line on a Single-Line Trimmer
- Prepare the line. The length and width of line you need varies based on your trimmer. ...
- Make sure your trimmer’s engine is turned off. If it has a gearbox, make sure it is cooled down. ...
- Remove the retaining cap from the trimmer head. ...
- Locate the starter hole in the spool. ...
- Line up the retainer with the slot on the outside of the head. ...
How to restring a Homelite weed wacker?
How to Restring a Homelite Weed Wacker
- Lay the trimmer on flat ground if you're starting up a cold engine.
- Check the fuel tank and make sure it contains gasoline.
- Press the primer bulb located on the top right of the trimmer engine about 10 times.
- Move the choke lever, located near the primer bulb, to the choke position.
How do you take apart a craftsman Weedwacker head?
How Do I Remove the Head From a Craftsman Line Trimmer?Deactivate your trimmer and remove it from any power source. ... Turn the trimmer upside down so that the head is facing up toward you. ... Depress each tab at the same time, releasing the head from the rest of the trimmer.
How do you clean the carburetor on a Craftsman string trimmer?
1:3622:28Craftsman / Ryobi String Trimmer / Edger - Walbro Carburetor CleaningYouTubeStart of suggested clipEnd of suggested clipCover it'll be two screws on this particular model they are star bits but you can also use a plainMoreCover it'll be two screws on this particular model they are star bits but you can also use a plain blade. In.
Why won't my Weedeater keep running?
Most weed eaters will have a small air hole available on the cap to the gas tank – This lets air into the tank to help prevent any vacuum from forming. An easy way to check if your air hole is clogged is to simply loosen the cap while the trimmer is running – If performance improves, a replacement gas cap is your fix.
How do you change the carburetor on a Craftsman Weedwacker?
1:1010:58Craftsman String Trimmer Carb Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipOpen up the breather. And of course they running it without an air filter that's about par. Let'sMoreOpen up the breather. And of course they running it without an air filter that's about par. Let's take that off get it anyway there's two Allen screws.
What are the symptoms of a dirty carburetor?
4 Signs Your Carburetor Needs CleaningIt just won't start. If your engine turns over or cranks, but doesn't start, it could be due to a dirty carburetor. ... It's running lean. An engine “runs lean” when the balance of fuel and air gets thrown off. ... It's running rich. ... It's flooded.
How do you clean a 2 stroke carburetor without removing it?
Spray liberally with carb cleaner – trying to direct the cleaner into the jets – and leave to soak for a few minutes. Use an air line (or a can of pressurised air, sold as an 'air duster') to blow through the jets. Repeat the previous step and this one until you can see no more gunge.
Why does my trimmer dies when I give it gas?
Why does my weed eater die when giving it gas? The most common causes of a weed eater dying when throttled are fuel issues, insufficient air intake, or problems with the exhaust. You should follow the path that the fuel travels to identify the issue.
Why does my trimmer keep shutting off?
A clogged fuel filter is most commonly caused by leaving fuel in the string trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.
Why does my gas trimmer keeps stalling?
0:042:00Top Reasons String Trimmer Starting, Then Stalling - YouTubeYouTubeStart of suggested clipEnd of suggested clipOver time the arrestor can become clogged with soot which may cause the trimmer engine to stall. YouMoreOver time the arrestor can become clogged with soot which may cause the trimmer engine to stall. You can try cleaning the arrestor with a wire brush. But you may need to replace it with a new.
How do you adjust the carburetor on a craftsman?
0:264:22HOW TO ADJUST CARBURETOR on Craftsman Hedge Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe L screws on the left and the high screws on the right. You will adjust the low screw when it'sMoreThe L screws on the left and the high screws on the right. You will adjust the low screw when it's idling and the high screw will adjust that with the throttle wide open until it runs the best.
How do you adjust the air fuel mixture on a Weedeater?
2:135:55HOW TO ADJUST The Carburetor on Weedeater XT260 Grass TrimmerYouTubeStart of suggested clipEnd of suggested clipOn these weed eaters is that the high screws here low screws there you adjust this screw here atMoreOn these weed eaters is that the high screws here low screws there you adjust this screw here at high speeds revving your machine up this one here you adjust it when it's idling.
How do you adjust a 25cc carburetor?
0:437:18Easy Weed Eater Carburetor Adjustment To FIX - BOGGING DOWNYouTubeStart of suggested clipEnd of suggested clipYou want to do the low side first. And when it's warmed up you start it let it idle and turn itMoreYou want to do the low side first. And when it's warmed up you start it let it idle and turn it clockwise. Until it starts bogging down a little bit. And then turn it counterclockwise.