how to repair a diverter valve

1. Turn off the water supply at shutoff valves or unscrew one end of the hose from its other on both ends of the diverter valve.
2. Remove all washers because they’re often damaged during repair attempts. ...
3. Open the new valve fully by pushing up or down depending on the direction of the pipe opening.
4. Locate the rubber washer where water will come out of and make a note of its location in relation to anything holding it back, like a screw, nut, ...
5. Put a new washer over the old one so that everything is held tightly together with no risk for future breakage! ...

Full Answer

How much does it cost to replace diverter?

Typically, it costs between $150 and $500 to fix a leaky or dripping faucet, depending on severity of the leak. Repairing a broken diverter will cost you around $125 on average.

How to replace a push button diverter?

Typical questions asked about products:

• Is the product durable?
• Is the product easy to use?
• What are the dimensions of the product?

How to replace a diverter valve in a peerless faucet?

Two-Handled Faucet Diverter

• Reach under the sink to rotate the hot and cold water supply valve clockwise. ...
• Place a rag over the cap behind the two-handled faucet spout. ...
• Insert a butter knife or a nickel into the slot at the top of the diverter. ...
• Wrap the clean diverter threads in one or two layers of thread-seal tape. ...
• Replace the faucet cap on the faucet body. ...

Is it OK to not use a skimmer diverter?

This is also mentioned in this post, Is it OK to not use a skimmer diverter? , as a safety feature. However in my case, which may be very rare, a few weeks ago my older Hayward cartridge filters lid cracked in half over night. I woke up to water spewing from the filter and a Pool that was 5 Ft. Lower!

Can a shower diverter be repaired?

It may be a simple job to put off, a damaged shower diverter wastes water and creates a bad shower experience. Repairing a shower diverter is a DIY job that you can complete in simply one day.

How do you fix a diverter valve on a faucet?

0:417:49How to repair replace 3 way Shower Faucet Diverter - FAST & EASY!YouTubeStart of suggested clipEnd of suggested clipSet the screw in a safe location. And we can pull the cap off now see how easy that was chances areMoreSet the screw in a safe location. And we can pull the cap off now see how easy that was chances are yours might not be that easy yours might be very rusted corroded and oxidized.

Can you replace diverter valve?

If your shower won't switch from the tub's spigot to the showerhead at all, this also could mean you need to replace the diverter valve. If you're not sure what a diverter valve is or what it does in your shower, make sure to take a look at our post about everything you need to know about shower diverter valves.

How do you fix a stuck diverter?

1:155:42DIY how to Fix Shower Tub Stuck Spout VINEGAR HACK Diverter ...YouTubeStart of suggested clipEnd of suggested clipAnd then dunk it face down and just leave it for a few days and what it will do is just take off allMoreAnd then dunk it face down and just leave it for a few days and what it will do is just take off all this calcium. And then it should pull up smoothly.

How do you rebuild a shower diverter valve?

How to Repair a Shower DiverterTurn off the water supply to your shower.Seal off your drain with tape so that small screws or other important parts are not lost down the drainpipe.Tighten the screws behind the faceplate of the diverter valve. ... Disassemble the shower diverter. ... Replace the diverter.More items...•

How do you clean a clogged diverter valve?

Remove the sink faucet diverter valve from the hole in the faucet body with needle-nose pliers. Soak the diverter for an hour or two in vinegar to break down the mineral deposits. Using a small brush, carefully clean the area on the faucet body where the diverter sits to remove any deposits or blockages from the area.

How do I know if my diverter valve is faulty?

A diverter valve may be faulty if the hot water taps still work while the radiators do not turn on. Another sign of a faulty diverter valve is if you only can only get lukewarm water from your taps.

How do you install a tub diverter repair kit?

0:243:44Replace tub spout diverter pull kit - DIY fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow a couple things i want to talk about first grab your pull and it's got this long rod or shaft.MoreNow a couple things i want to talk about first grab your pull and it's got this long rod or shaft. And the top pole here and in the event that this part separates from the rod go ahead and screw it

How do I free a stuck shower valve?

0:202:38DIY plumbing tips fix a leaky or stuck shower faucet handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's causing you problems you should be able to easily remove the cartridge with a pair of pliersMoreIt's causing you problems you should be able to easily remove the cartridge with a pair of pliers now aside from using a brand new cartridge. You might be able to utilize your old cartridge.

Can you use wd40 on shower diverter?

Hard water can build up and deposit in your tub spout diverter, causing it to clog. Spray some WD-40 with the spray nozzle pointed upward into the spout to the diverter valve to lubricate it. Do this a few times and it should clear any clogs.

How to replace a valve cover?

REPLACE VALVE COVER - Insert the Valve Cover onto the Valve Housing. Note that the bottom of the Valve Shaft fits into the hole in the bottom of the Valve Housing. Ensure that the "INLET" label on the Cover is over the common port as noted in Step 7 and push the cover down as far as it will go.

How to relieve pressure in a filter?

RELIEVE PRESSURE - Relieve the pressure in the lines by turning the relief valve on top of your filter counter-clockwise. You should see the pressure reading on the filter pressure gauge go to 0.

Where is the inlet label on a valve?

NOTE POSITION OF "INLET" LABEL - Note the position of the "INLET" label on the valve cover. "INLET" is positioned over the Valve's common port. When you replace this cover, you will place it with the "INLET" label over the same port.

How to tell if a shower diverter is a two valve or three valve?

When you remove a tee-valve from the wall, you find a single copper pipe. With two-valves and three-valves, you’ll find the corresponding number of copper pipes . If your shower diverter is a two-valve, focus on the temperature dial. This is because it often doubles as a shower diverter gate.

What to do if your diverter gate is stubborn?

If your diverter gate stays stubborn after your vinegar soak, try using a lubricant to make it work better. Any cooking spray will do, and you probably have some in the kitchen.

What does a shower valve do when it is not working?

If your bathtub has a showerhead, your shower valve redirects water from the showerhead to the tub faucet. When it’s not working, water simultane ously pours from both outlets. It’s easy to fix, so let’s learn how. Shower valves have two parts:

Why does my diverter gate keep squeaking?

Option 1 – Clean your spout. Sometimes, the diverter gate gets stuck. When you try to turn it or pull it up, it refuses to budge or makes squeaky, grating noises. If you do manage to pull it up, it may stick at the top and refuse to push back down. This is probably due to accumulated dirt, grease, and limescale.

How to clean a spout with vinegar?

If you like, you can mix the vinegar with water. Step 3: Wrap the plastic bag around your spout, submerging the spout. Step 4: Hold the bag in place using a rubber band, string, or shoe-lace. Step 5: Leave the faucet submerged for three or four days, checking it once a day.

How to stop a handheld shower from leaking?

When you want to stop your handheld showerhead from leaking, you need to clean the inner parts of your diverter gate. Step 1: Turn off your water supply from the main spigot. This prevents flooding.

What tool to remove a screw from a faucet?

2. Note that the tool to remove the screw could be an Allen Wrench, Flat Head Screwdriver, or a Phillips Head Screwdriver. 3.

How to make sure water is coming out of shower head?

1. Start this process by ensuring that the water is coming out of the tub faucet and not the shower head. Although it is not necessary to turn off your water supply, you want to make sure that if water does start coming, you don’t get soaked in the process! 2.

How to remove a knob from a sandbox?

Start by removing the knob. Find the screw, if not visible it is located under the plastic button which will need to be popped off using a small flathead screwdriver. 1. Once the knob has been removed, use your hand or a handle remover to remove the base.

Is it bad to have a shower faucet leaking?

It is never a good thing when your shower tub faucet starts leaking, but it is a good thing when you know what to do to fix it! As long as you have the time, tools, and parts for the job you can definitely learn how to fix shower diverter all on your own!

What is a shower diverter valve?

A shower diverter valve switches the supply of water from the faucet to the shower head and back again. Repeated operation over time can wear out the valve or the rubber washers and result in drips and leaks. Two handle faucets typically have one of two types of diverter valves.

What to do if shower valve won't release?

If it won’t release, check to see if it’s caulked to the wall, and cut the caulk. A strap wrench might help encourage a stubborn one to turn. To remove recessed valves like the one shown, you’ll need Shower Valve Socket Wrench Set. A shower-valve set provides the super-deep wrenches needed to remove tub and shower valves.

What to do if escutcheon doesn't budge?

If the handle refuses to budge, you can use a gear puller to remove it. It might be necessary to remove the escutcheon if it interferes with the use of your deep-socket wrench. Escutcheons are often held with a retaining nut, but if not then the escutcheon is threaded over the valve stems.

How long does it take to replace a shower diverter valve?

How to Replace a Shower Diverter Valve in 10 Minutes. If you have a shower-bathtub combination in your bathroom, you then surely have a shower diverter which as its name suggests diverts water to the shower head from the tub spout and back to the spout when needed.

How to tell if shower diverter is bad?

The signs of a bad shower diverter are a leaking bathtub faucet when the shower is on, not enough hot water, unbalanced/irregular water flow, sticky handle/knob or a sudden gash of hot water when someone flushes the toilet or runs another appliance.

How many handles does a shower faucet have?

Double handle shower faucet. Here you will have 2 shower faucet handles, one for the cold water and the other one for the hot water. You will also have a pull-up shower diverter at the top of the bathtub spout. Three handle shower faucet.

What is an escutcheon on a valve?

An escutcheon is the trim plate which hides the valve opening on the wall. The escutcheon will either be threaded on the valve stem or held in place using a retaining nut. Before attempting to remove the escutcheon, check if it is caulked to the wall. If it is, cut through the caulk with a putty knife.

What is the middle handle of a shower?

As I had mentioned earlier, the middle handle/valve is usually the shower diverter valve. Water flows from both the hot and cold faucet valve and when it reaches the shower diverter it flows either to the bathtub spout/spigot or shower head depending on the position of the valve.

Why does my shower head not have a spout?

When the rubber washer is in contact with the valve seat, a watertight seal is created allowing water to flow to the shower head but not tub spout. With the time, due to the friction between the rubber washer and the valve seat, the washer starts to wear out, failing to seal properly.

How to check if a shower head is leaking?

Turn on the water and divert it to the shower head and check if the pressure and temperature are good. Check if the bathtub spout is leaking with the shower turned on. Divert the water to the tub spout and check as well if everything is at it should.