Repairing Guides

how to repair a fiberglass tent pole

by Rosalinda Wyman Published 3 years ago Updated 2 years ago
image

  • Get rid of the duct tape from the pole and sand the edges of the pole to get a smooth surface.
  • Place the full pole of the tent on the floor and start to untie the knot on the end that is closer to the section that is to be replaced. ...
  • Hold the shock cord and remove the pole sections carefully until you reach the broken part that is to be replaced.
  • Remove the damaged section and replace it with the section that you prepared.
  • As you still hold onto the shock cord, re-stretch it through the pole sections that you had removed temporarily. ...
  • Tie a knot at the end of the cord and make sure that it is taught just as you had found it. ...

Part of a video titled fixing BROKEN “fiberglass tent poles” (not just replacing)
0:09
2:23
So we'll just cut the knot. Off move the elastic. Until we get to our broken pole. Here thisMoreSo we'll just cut the knot. Off move the elastic. Until we get to our broken pole. Here this fiberglass shock cord is split in half years ago i put epoxy on it and this tape. And it worked for years.

How to replace a tent pole?

Get rid of the duct tape from the pole and sand the edges of the pole to get a smooth surface. Place the full pole of the tent on the floor and start to untie the knot on the end that is closer to the section that is to be replaced.

What happens when a tent pole breaks?

The fiberglass poles that are used to support tents are usually made of loose pole sections that are held together by an elastic cord. The elastic cord, also known as a shock cord, runs through the length of the poles and it is knotted at both ends. When your pole gets broken, it is most likely that only one of the sections is broken.

What are fiberglass tent pole replacement parts used for?

Take a look at the process of fixing a broken fiberglass tent pole and what are fiberglass tent pole replacement parts that you will use. The fiberglass poles that are used to support tents are usually made of loose pole sections that are held together by an elastic cord.

What are the poles on a tent made of?

The fiberglass poles that are used to support tents are usually made of loose pole sections that are held together by an elastic cord. The elastic cord, also known as a shock cord, runs through the length of the poles and it is knotted at both ends.

image

How do you Rethread Fibreglass tent poles?

0:443:33How to Repair your Broken Fibreglass Dome Tent poles! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe've done this a little bit later on I'll show you alright she's just going to show you how to readMoreWe've done this a little bit later on I'll show you alright she's just going to show you how to read thread your tent poles if one happens to break or shock or breaks on.

Can you repair a tent pole?

The easiest and quickest way to fix a broken pole is with a pole repair sleeve. Also called a splint, this short tube is often provided with your tent. If not, buy one and pack it with you. A good pole repair sleeve is just slightly larger in diameter than your pole so that it doesn't move around too much.

How do you fix a splintered tent pole?

0:184:55How to repair a broken tent pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a spare but replacement Palmeri threading all the shock cord. So first of all we need a brokenMoreUsing a spare but replacement Palmeri threading all the shock cord. So first of all we need a broken tent pole. Oh. My god here's one I broke earlier. So you can see there.

Can you cut Fibreglass tent pole?

When cutting the section to length, always cut towards the centre to avoid splintering the edge when you cut through. Cut part way through the pole, then turn it and cut part way. Repeat until you cut right through. Once you've cut all the replacement sections for one pole, fit them before moving on to the next pole.

Can you replace fiberglass tent pole?

0:144:08How to Replace a Broken Section of a Fiberglass Tent Pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're gonna use an old one a section to replace it with job one get the knot out not on the very endMoreWe're gonna use an old one a section to replace it with job one get the knot out not on the very end of the pole. It has to be pulled out. And either untied or cut off I'm gonna untie.

What is a tent pole repair sleeve?

0:031:13How to Use a Pole Repair Sleeve | NEMO - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut by any sharp metal points if if they do happen to occur during that break. You're gonna slideMoreCut by any sharp metal points if if they do happen to occur during that break. You're gonna slide that pole repair splint right over the damaged area Center that damage in the splint.

How do you fix a broken pole?

1:369:30How to repair a broken fishing rod: a simple fix that lasts - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo cut pieces I've got my exacto knife I need a marker to mark my position. We need some epoxy glueMoreTo cut pieces I've got my exacto knife I need a marker to mark my position. We need some epoxy glue and we need some sandpaper. Now. I've got some CA glue here because I want to go fast.

What can I use to replace tent pole?

0:093:56How To Repair A Broken Tent Pole Section - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you simply need to measure mark. And cut the pole down with a hacksaw. And then with a sandpaperMoreSo you simply need to measure mark. And cut the pole down with a hacksaw. And then with a sandpaper just remove any sharp edges this will prevent them from damaging the elastic in your pole sections.

How do you use a tent pole splint?

0:140:58How to use your repair splint - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep one to properly use your pole splint. Simply slide the splint over the broken pole segment.MoreStep one to properly use your pole splint. Simply slide the splint over the broken pole segment.

How do you cut a Fibreglass pole?

Put on your safety glasses. Place one hand on the fiberglass stick, close to the pencil mark you placed on the masking tape in Step 3. Align the back edge of the fine-toothed hacksaw blade with the pencil mark. Slowly pull the hacksaw toward you and then away from you to cut into the fiberglass stick.

How do you remove tent pole ends?

0:081:54How to Replace a Tent Pole Section - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will find a knot and a bungee cord on that metal part at the end there's a little hook that youMoreYou will find a knot and a bungee cord on that metal part at the end there's a little hook that you can just pull on. And then it's gonna be released. By pulling onto two ends.

How do you repair an aluminum pole?

0:593:45How to repair aluminum tent poles! Permanantly! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I got some jb weld also from the big orange box store and I mixed that up I spread it all aroundMoreAnd I got some jb weld also from the big orange box store and I mixed that up I spread it all around that piece that was all mangled on there I straightened it out as good as I could first and then.

How do you fix a bent aluminum pole?

The only way to soften the aluminum is to anneal it, which involves heating the aluminum almost to it's melting point and then letting it cool slowly, but if you try to do that then your pole will be so soft that it won't flex, it'll just bend like welding wire.

What happens if a tent pole breaks?

When your pole gets broken, it is most likely that only one of the sections is broken. You will have to replace it to regain the proper functionality of the tent. The process of doing so is as follows.

What holds the poles in place in a tent?

The cord holds the poles in place and gives the tent a defined structure. This is why you should make sure that it is taught enough. If you notice that this is not the case when you set up the tent later on, get the end of the shock cord and adjust the knot. You can do this from either end of the poles.

How to untie a knot on a tent?

Place the full pole of the tent on the floor and start to untie the knot on the end that is closer to the section that is to be replaced. Use a needle nose plier to get the end of the knot from the pole as it is unlikely that you will be able to reach it with your fingers. The knot may have been tied tightly and you may have to cut it.

How to replace a broken shock cord?

Hold the shock cord and remove the pole sections carefully until you reach the broken part that is to be replaced. Remove the damaged section and replace it with the section that you prepared. As you still hold onto the shock cord, re-stretch it through the pole sections that you had removed temporarily.

How to prevent fiberglass from getting into your eyes?

To make sure that you cut the right length of the replacement pole, use duct tape to hold the pole in place as you make the cut. This will prevent the formation of splinters as you will be able to cut in an orderly fashion.

What to do if your pole breaks?

If your pole breaks you can use a stake to connect the two broken parts together.

Can you fix a broken tent pole?

Tent poles break all the time but this doesn’t mean that you will have to get rid of the tent and buy a new one. You can fix a damaged pole by yourself. With my advice, you are able to repair a broken fiberglass tent pole without a hustle.

How to fix a broken tent pole?

Using a repair sleeve to fix a broken tent pole is simple: Line up the broken pole sections. If the pole is bent but not fully broken, gently straighten out the bend. Slide the sleeve over the pole end until it’s centered over the break or kink; you might have to use pliers to crimp or a rock to bend splayed pieces so that ...

What to do if a tent pole gets stepped on?

Whether your tent pole gets stepped on or a powerful gust of wind does the damage, a kinked, split or snapped pole needs immediate attention in the field (when you get home, you can look into having the pole replaced or professionally repaired.) You have two options: Use a pole repair sleeve. Use a tent stake as a splint.

How to tie a shock cord?

Tie a knot in one end of the shockcord, then feed the other end through all but the last pole section. Stretch the shockcord to extend its length, then tie a temporary knot to keep it from slipping back inside the second-to-last pole section; alternatively, you can use a pair of locking pliers to hold the cord.

How to replace shockcord on tent pole?

Fortunately, replacing it is a straightforward process. Here’s what you’ll need: Here’s how to replace the shockcord: Start by laying the tent pole out straight. To avoid mixing up sections, you can label them with a permanent marker (use masking tape if you don’t want to write directly on the pole.)

What happens if a tent pole breaks?

If your pole breaks where one pole end inserts into the next one, you will have to splint the sections together; keep in mind that this will prevent the poles from folding up neatly when you take the tent down.

What is a splint for a tent pole?

Also called a splint, this short tube is often provided with your tent. If not, buy one and pack it with you. A good pole repair sleeve is just slightly larger in diameter than your pole so that it doesn’t move around too much. Using a repair sleeve to fix a broken tent pole is simple: Line up the broken pole sections.

Can you use a shockcord pole in the field?

If the shockcord snaps while you’re in the field, you can still use the pole by carefully assembling the individual sections. However, when you get home, you’ll want to replace the shockcord; it makes assembly simple and keeps you from losing a pole section. Fortunately, replacing it is a straightforward process.

Why do my tent poles keep breaking?

Causes range from strong winds to poles weakened by age to cheap materials—and sometimes, it’s just plain old wear and tear.

How do you remove a ferrule from a tent pole?

Jam the pole in a vice and heat the tip of the ferrule with a heat gun,grasping the ferrule as it is heat with pliers turn it to see if it starts to move. Care must be taken not to over heat as you will burn the pole.

How do you clean cut fiberglass?

The Best Ways to Cut Fiberglass Panels Router. If you choose to use a router to cut your panels, use a blade with a fine edge that will make clean and smooth edge cuts. Fiberglass Power Trimmer. A trimmer is lightweight and powerful, and it easily cuts through hard fiberglass, such as that used in paneling. Jigsaw. Circular Saw. Hacksaw.

Can I make my own tent?

Your Tent, Designed Just for You In just a few clicks, you can build your own piece of outdoor heaven, from the size of the tent you want to the very fabric that it’s made of. It’ll be perfect for you and your needs because you’re the one who designed it. Build your own tent today.

How do you fix a broken tent?

Here’s how to patch a rip in your tent: On the exterior of the tent, start by cleaning the area around the tear with rubbing alcohol and a rag. Cut a piece of repair tape to cover the hole and at least one inch of fabric surrounding it. Lay the tent fabric on a solid surface and remove the backing on the tape patch.

What does tent pole mean?

In broadcast programming and motion pictures, a tent-pole or tentpole is a program or film that supports the financial performance of a film studio or television network. It is an analogy for the way a strong central pole provides a stable structure to a tent.

How long should tent pole shock be?

What you’ll need: Shock Cord (1/8″ or smaller). You need at least the length of all your poles combined. My poles were 152″ each, I bought 30′ (or 360″ of cord).

Step 2: Getting Started

Cut the knot off on one end of the elastic and remove the poles from the elastic .

Step 3: Cutting to Length

Mark the length of the old pole next to the new pole. Hold the new pole firmly and very slowly cut the pole to size making sure not to tear the fibers . WEAR A MASK WHEN WORKING WITH FIBERGLASS .

Step 4: Sanding

Slowly sand the top of the pole to remove any splinters next sand the edges to a cone shape until smooth . Test fit the poles to make sure they fit snugly into each other .WEAR A MASK WHEN WORKING WITH FIBERGLASS .

Step 5: Threading the Elastic

To thread the elastic knot one end of the elastic and tie the fishing line to the knot free end you will need roughly twice the length of the pole in fishing line then just tie the needle on the end make sure the knot s small enough to fit inside the pole freely .

Step 6: Last Pole

You will have to pull the elastic tight through the last two poles so hold it around your finger then tie a double knot at the end of the elastic cut off the fishing line and its done .

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9