How To Repair A GE Dryer That Won’t Start
- This guide covers all major GE dryer models, including:
- Make sure the power is working. If your GE Dryer won’t start, you first need to rule out if it’s being caused by a power supply problem.
- Make sure the thermal fuse hasn’t blown. ...
- Check that the start switch is working. ...
- Check that the door switch is working. ...
- Check that the drive motor is working. ...
Full Answer
How to disassemble a GE Profile dryer?
- Heating element: If your dryer does everything but heat up, there's a good chance that its heating element is the number one suspect. ...
- Thermostat: Dryers have multiple thermostats to monitor internal temperature. ...
- Timer motor: This little device does a big job, regulating how and when power is sent to each component. ...
How do I remove back of GE dryer?
To clean area under the lint filter:
- Remove the lint screen, and use a vacuum to remove any small bits of leftover lint.
- Take the lint trap screen to the sink, and wash it with warm soap and water.
- While the lint trap dries, use your vacuum to clean the slot the lint trap slides into.
How to repair a GE garbage disposal?
You can head off garbage disposal repair by following some best practices:
- Run the unit regularly to prevent rust and corrosion.
- Use cold water to flush the food scraps. ...
- Keep the disposal clean by pouring some dish soap in and letting it run for a minute with cold water.
- Don't overload the disposal; grind no more than about 1 cup of food debris at a time.
How to repair a noisy GE microwave?
There are several key steps to doing that, and they are as follows:
- Discharge the magnetron’s high-voltage capacitor
- Verify that the mounting bolts are tight
- Make sure that the high-voltage diode is working (I will go over the diode a little later).
How do you fix a GE dryer that won't start?
If your dryer will not run or start, check the following:Make sure the dryer plug is pushed completely into the wall outlet.Check that the dryer door is closed tightly.Make sure that the cycle selection button is positioned on the desired temperature, fabric and drying time.More items...
How do you troubleshoot a GE dryer?
0:0010:09Dryer Troubleshooting Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipHopefully we can solve the problem for you if your dryer doesn't turn on check and make sure it'sMoreHopefully we can solve the problem for you if your dryer doesn't turn on check and make sure it's plugged. In if it's plugged in check the circuit. Breaker.
How do I service my GE dryer?
0:193:19GE Dryer Disassembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour first step is to remove the screws at the rear of the control panel to release. It. Next openMoreYour first step is to remove the screws at the rear of the control panel to release. It. Next open the dryer door and remove the screws inside the door frame which secure the main.
What would cause a GE dryer not to heat?
Clogged Vents and Lint Filter If your GE dryer is not heating, the first thing to check is the lint filter and vent. If the vent is blocked, your dryer may still produce heat, yet it will take a significant amount of time to dry clothes. A clogged vent can prevent the necessary airflow to create heat.
How do you diagnose a dryer problem?
0:5836:35Dryer Troubleshooting - Top 10 Dryer Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt could be caused by a rattling vent in the back. If it's not connected securely. Sometimes thisMoreIt could be caused by a rattling vent in the back. If it's not connected securely. Sometimes this can rattle and make a noise that way other times the rollers. If they're not spinning.
Is there a reset button on a GE dryer?
How do you reset a GE dryer? Turn the dryer off, then on again to reset it. Or you can press the reset button on the dryer plug.
Why is my GE dryer not drying?
Check the household fuse or circuit breaker that supplies power to the dryer. Make sure they are not burned out or tripped. There may be too many items in the dryer. Only dry one wash load at a time.
What causes a dryer to stop working?
A faulty or broken thermostat can make a dryer stop working. Replacing the fuse or the thermostat will allow the dryer to work again. A blown thermal fuse from overheating indicates an additional problem, such as improper ventilation.
Where is the thermal fuse in a GE dryer?
The thermal fuse will be located next to the heating element housing. Look for a white strip with two wires connected to it and you've located the thermal fuse in your GE dryer.
How do you check a heating element on a GE dryer?
1:055:36Heating element in a GE electric dryer - Learn how to check & replace the ...YouTubeStart of suggested clipEnd of suggested clipTake a reading between these two terminals. There really should be about 44 ohms if the reading isMoreTake a reading between these two terminals. There really should be about 44 ohms if the reading is oil the heating element is bad and you need to replace it take a reading between this terminal.
Where is the reset button on a dryer?
Often, dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then press this reset button.
Why is my GE dryer not drying?
Check the household fuse or circuit breaker that supplies power to the dryer. Make sure they are not burned out or tripped. There may be too many items in the dryer. Only dry one wash load at a time.
Where is the thermal fuse on GE dryer?
The thermal fuse will be located next to the heating element housing. Look for a white strip with two wires connected to it and you've located the thermal fuse in your GE dryer.
How do you check a GE dryer start switch?
0:433:35See how to check & replace the start switch GE dryer - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull all the controls panel a little bit slide it to the right and then let it hang disconnect theMorePull all the controls panel a little bit slide it to the right and then let it hang disconnect the wires from the switch.
Step 1 – Make sure the power is working
If your GE Dryer won’t start, you first need to rule out if it’s being caused by a power supply problem.
Step 3 – Check that the start switch is working
The start switch turns your dryer on when you put it onto a cycle. If it becomes faulty, your dryer might not start.
Step 4 – Check that the door switch is working
Another possible reason your GE dryer won’t start is if the door switch is defective. This particular switch monitors the door on your dryer to make sure it’s closed and then tells the control board it’s safe for your dryer to start.
Step 5 – Check that the drive motor is working
The next step is to check the drive motor to ensure it’s working properly. The drive motor provides the power to spin your dryer drum. If the drive motor stops working, your dryer won’t be able to start.
Step 6 – Check that the drive belt is properly attached
If you’ve ruled out all the electrical components as being the cause of your GE dryer not starting, the next component to check is the drive belt. The drive belt goes around the dryer drum and helps guide and turn the drum when the dryer is in operation. Sometimes the drive belt snaps or slips out of place, which will stop your dryer from starting.
Step 7 – Consider replacing the main control board
The final step is to consider replacing the main control board. The board is difficult to test and/or repair so your best option is to just replace it and see if your GE dryer starts working again. Alternatively, it may be a better bet to just buy a new dryer.
Step 1 – Check the thermal fuse
When fixing a GE dryer that isn’t heating, the best place to start is to check the thermal fuse. The thermal fuse turns your dryer off when it overheats. However, sometimes it can do this for no reason, which stops your dryer from heating at all.
Step 2 – Check the power sources
The next step is to check the incoming power sources. Your GE dryer requires two legs of 120 volts AC (a total of 240 volts) to work. If the circuit breaker or fuses that provide power to your dryer trip, the incoming power source to your dryer can become infringed or cut off completely, which prevents the dryer from heating.
Step 3 – Check the gas valve solenoid
The next step is to check the gas valve solenoid. If your dryer is electric, proceed directly to step 6. Your gas-powered dryer has two or more solenoid coils that open to supply gas to the burner. When they don’t correctly open, your GE dryer won’t heat up.
Step 4 – Make sure the igniter works
The next step is to check the igniter. The igniter is responsible for igniting the gas when you turn your dryer on. If the igniter fails, your dryer won’t heat up.
Step 5 – Make sure the flame sensor works
The purpose of the flame sensor is to monitor the heat coming from the flame to ensure your dryer is at the correct temperature. If it stops working your dryer won’t heat up.
Step 6 – Make sure the heating element works
The next step is to test the heating element. The heating element is how your dryer heats the air that is then distributed throughout the dryer. If the heating element stops working your dryer will too.
Step 7 – Make sure the high-limit thermostat is working
The purpose of the high-limit thermostat is to monitor the temperature in your dryer and send a signal to the control board to turn the dryer off if it overheats. If the thermostat stops recording accurate temperatures or stops working completely, your dryer won’t be able to heat up.
Why does my dryer keep shutting off?
Laundry not getting dry? Let's find out why your dryer runs for a few minutes then shuts off. Read More
Why won't my dryer spin?
Dryer drum not turning? Let's narrow down the issue and get your laundry routine back on track. Read More
Why won't my dryer start?
Dryer not starting? Then neither is your laundry routine! Let’s get everything back on track. Read More
Why does my dryer vent have water in it?
Water in your dryer vent? Learn how your dryer ended up with a wet problem—and how to fix it. Read More
HOW GE APPLIANCES FACTORY SERVICE WORKS
Conveniently schedule service online or call us toll-free at 844-988-4066.
