Repairing Guides

how to repair a hand blender

by Weston Zieme Published 2 years ago Updated 2 years ago
image

How to Repair Hand Blenders

  1. Test the Switch. The most common hand blender problems are issues regarding their switch. ...
  2. Open the Motor Body and Clean. Use a screwdriver to open the motor body and carefully check the unit, particularly its switch. ...
  3. Check the Fuse. ...
  4. Check the Blade Shaft. ...
  5. Reassemble the Hand Blender. ...

Full Answer

How to fix a blender that won’t turn on?

Always search by the make and model of your hand blender as well. If the blade shaft is jammed, disassemble your model of hand blender until you can gain access to it. The cause of the jam is usually food and debris buildup lodged in the joints. Clean out anything you see, and then use a white grease to lubricate these rough areas further.

What is a blender fix-it guide?

This Fix-It Guide also refers to electrical cord repair, fuse repair, appliance controls repair, and motor repair for more information. How Does a Blender Work? Turn the blender over to access screws holding the baseplate. A food blender uses a motor to power blades that chop, and grate food.

How do you fix a jammed hand blender blade?

If the blade shaft is jammed, disassemble your model of hand blender until you can gain access to it. The cause of the jam is usually food and debris buildup lodged in the joints. Clean out anything you see, and then use a white grease to lubricate these rough areas further.

What are the most common hand blender problems?

The most common hand blender problems are issues regarding their switch. If you try to switch on your blender and it is not working at all, you may need to check it by using a volt-ohm meter. Connect the plug prongs of your hand blender to the volt-ohm meter, setting the meter on the RX1 scale.

image

Can a hand blender be repaired?

Problems with hand blenders are common and also fairly easy to repair on your own. However if you are unable to do the repair work, then you can always contact a professional for blender not working or other problems.

How do I fix my handheld blender?

The following are some tips to repair a hand blender.Test the switch. The first way to repair a hand blender is to test the switch since the most common problems with this appliance are related to the switch. ... Open and clean the motor body. ... Check the fuse. ... Check the blade shaft.

How do you fix a hand blender that won't spin?

Step 1: Remove the blender base and locate the fuse in the wire from the multispeed switch to the motor. Step 2: Disconnect the wire and use a continuity tester or multitester to check the fuse. If the circuit is open, the fuse is blown. Step 3: Replace the faulty in-line fuse with one of identical rating.

What causes a blender to stop working?

A burned-out fuse will cause your blender not to turn on. To check if the fuse is blown, remove the base cover and inspect either the motor switch or circuit board for a blown fuse. You can use a multimeter to test for continuity; the fuse is blown if the circuit is open.

Why is my blender not blending?

There may be times when an air pocket is created around the blade, causing the ingredients to miss the blending blade. Unplug the power cord. Remove the Blender Jar from the base, and use a spatula to rearrange ingredients in the Blender Jar. Turn the Blender on to continue use.

Why does my blender smell like it's burning?

Blenders with heavy use will have worn out brushes over time. The brushes will arc, resulting in a burning smell and possibly some smoke. The carbon brushes are used in electric motors to transfer electricity to the armature inside the motor. Brushes wear down over time and stop coming in contact with the armature.

Why is my blender blade won't spin?

Most of the time when your blender is powered on and the blades will not rotate, it is because you have overfilled the container. Remove some of the food/liquid and try to power on your blender again.

What can you do with a broken blender?

So, the best way to dispose of a blender is to recycle it. There are many provisions for this, and you can start with curbside recycling, appliance recycling depots, or even companies that accept small appliances.

Why is my mini blender not working?

The most common reasons a portable blender will not work are a lack of charge or an overload. Be certain that you have properly charged the portable blender before use. A solid red light on most models means that it is fully charged and ready to blend.

How do you know if your blender is broken?

5 Signs It's Time to Replace Your BlenderIt stops midway through blending. This is pretty much an obviously sure sign it's dead. ... The motor is slow or inconsistent. ... The cord is starting to fray. ... It's leaking. ... You want a blender that does more.

How long should blender last?

How long do blenders last? In general, less-powerful blenders will last three to five years, while more expensive models with a powerful motor will last about 10 years. However, how often you use your blender will impact its lifespan.

Why is my portable blender flashing red?

Red flashing lights mean your BlendJet needs to be recharged or that your blades are blocked. Recharge or shake your BlendJet, and/or turn it on upside down, then flip it back over while on.

How do you assemble a hand blender?

0:040:43How to Use a Hand Blender - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first step is to assemble the hand blender using the instructions that came with it now put theMoreThe first step is to assemble the hand blender using the instructions that came with it now put the ingredients into your pan or the bowl.

How do I fix my blender jar?

0:123:19Blender Repair - JB Weld on broken Blendtec jar - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what i did is i took some gorilla glue like gorilla super glue.MoreSo what i did is i took some gorilla glue like gorilla super glue.

How do you open a stuck blender base?

1:422:54Is your blender base stuck?? Here's an easy way to get it unstuck!YouTubeStart of suggested clipEnd of suggested clipThese things hold the base in place. So you can just use all your force concentrating on all usingMoreThese things hold the base in place. So you can just use all your force concentrating on all using all your force. And just twist. It.

What Are the Steps to Blender Repair?

Wear a leather glove to hold the fan in place as you disconnect it from the motor shaft.

What to do if blender doesn't work?

If the blender doesn’t work at all, make sure power is on at the outlet. Check the electrical cord. Test the fuse with a multimeter. Test the multi-speed switch (see the Appliance Controls Fix-It Guide ). If all this fails you’ll need to test the universal motor.

What Can Go Wrong with a Blender?

Because blenders are simple motorized small appliances, the things that can go wrong also are simple. The electrical cord, motor, switches, or fuse may fail. Parts may become loose or worn and seals may leak. (To avoid spills, don’t fill the blender jar more than two thirds full when in use.)

How to remove a blender base plate?

Unplug the blender and remove the jar. Undo the screws securing the baseplate. Separate the baseplate and attached motor collar from the base housing.

How to clean a blender jar?

If it is too difficult to disassemble jar, you can wash it by hand. Fill the jar half full with warm water and add a drop of liquid detergent. Cover and blend the mixture at low speed for five seconds. Run the blender with clean water to rinse, then run it empty to dry the blades. Finally, remove the blades and wipe them with a cloth to get rid of any residue.

How does a food blender work?

A food blender uses a motor to power blades that chop, and grate food. A blade inside a jar is connected to a motor shaft inside the unit. The blade’s speed is controlled by varying electric current to the motor using one or more switches. Blenders come in countertop and hand-held models.

How to attach a wrench to a blender shaft?

Grip the drive shaft with a wrench or pliers, then turn the blender on its side to attach a wrench to the drive stud.

Step 1: Taking It Apart

Technically, the first step to repair was waiting for a while. There might have been a self-resetting safety mechanism inside the case, so I waited a few hours and then powered on the motor. Nothing happened, which gave me some confidence that there was an actual break somewhere.

Step 2: Examining and Testing Internal Components

With the top cover off, the first thing noticed was a small yellow block. Searching for the part number identified it as a capacitor. It didn't look to have any physical problems (distortion, holes, smoke stain) so I checked it with a meter and it looked OK. Time to push on.

Step 3: Accessing and Testing the Fuse

To get access to the fuse required removal of the switch. To remove the switch required access to two screws right inside the base of the casing. To get access to those screws required removal of the control knob. To remove the control knob, about four hands were required to bend and stress various plastic catches at the same time, which is why there is no photograph of that..

Step 4: Replace Fuse, Insulation and Case

After an afternoon of driving around, I sourced a replacement. Thank you Jaycar! (Other suppliers are available. They just don't carry 2A slow-blo)

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9