
- Drain the water from the pool completely.
- Cut a circle or oval patch slightly larger than the hole to be repaired. ...
- Dry the area around the hole with a paper towel.
- Rub the area around the hole with an alcohol swab to remove dirt and grease that could interfere with the rubber cement bonding.
- Wipe off any remaining alcohol with a paper swab.
- Inflate the pool as much as possible. The patch is not as effective if applied when the pool is deflated.
- Apply rubber cement around the hole in an area a little larger than the repair patch.
- Place the patch on the rubber cement and smooth down any air bubbles to ensure the patch is airtight and watertight.
- Apply a little rubber cement on top of the edge of the patch. This provides an extra seal between the patch and kiddie pool.
...
Patch It Up!
- Step 1: Drain The Water. ...
- Step 2: Cut The Patch. ...
- Step 3: Dry And Clean The Patch Area. ...
- Step 4: Inflate The Kiddie Pool. ...
- Step 5: Apply The Glue. ...
- Step 6: Apply Your Patch. ...
- Step 7: Let It Dry.
How do you fix a pin hole in a pool liner?
To patch a pin hole, a 3 inch round patch would work best. Completely dry the area the patch will be applied. Clean the area with rubbing alcohol or other sanitizing cleaner. Make sure there is no dirt or debris that will get in between the patch and the pool material.
How to fix a hole in an inflatable pool?
First, drain all the water out of the inflatable pool completely. The patch will hold up and be much more permanent if it’s applied to a dry surface. If the hole is on the outside of the inflatable pool, you might get away with leaving the water in, I’ve just always found it easier to empty the pool before working on it.
How do you fix a cracked swimming pool?
When patching, you’re encouraged to drain your pool below your target repair area and remove any loose cement on the surface of your pool floor. Once the plaster is mixed to your preferred density for patching, you can apply it to any cracks you might see.
How do you fix a leak in a kiddie pool?
Both types of leak are repaired in the same manner. Most kiddie pools come with a hole repair kit, but you can use virtually any type of repair kit. Drain the water from the pool completely. Cut a circle or oval patch slightly larger than the hole to be repaired.

Can you fix a hole in plastic pool?
To fix a hole or crack in a hard-plastic kiddie pool, get some marine silicon or a hot glue gun and seal the crack or hole. Use a card or putty knife to even out the silicon and let dry. A few coats may be needed. Make sure to let it dry after each coat you apply.
Can you patch a plastic kiddie pool?
Re: Repairing a hole in plastic kiddie pool OTOH, maybe just put a thin coat of Shoe-goo on it, let dry. Repeat 2 more times, then add a piece of Tenacious Tape or Gorilla Tape over it. Even a waterproof band-aid might work.
What can I use to patch my plastic pool?
Option 1: Patch ItWaterproof tape - Similar to duct tape, waterproof tape can be used underwater, it's UV resistant, and it's clear (so your pool can stay beautiful).Vinyl patch kit - This is a better option for larger tears and lasts long-term. ... Peel-and-Stick- This is as easy as it sounds.
How do you fix a big hole in a vinyl pool?
4:4313:53How to Repair X-Large Tear on a Leaking Vinyl Liner Pool ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'll try to put some sand inside the holes. And clean the area before applying. The. Patches theMoreI'll try to put some sand inside the holes. And clean the area before applying. The. Patches the first part has to cover the tear. And i will add at least four inches on each side. Since i am dealing
How do you fix a small hole in an inflatable pool?
0:473:29Fix Leaks inflatables Pools Rafts Towables Air mattresses EtcYouTubeStart of suggested clipEnd of suggested clipProbably not I'll just take the shoe goo and the pool is actually usable if it's a small hole. JustMoreProbably not I'll just take the shoe goo and the pool is actually usable if it's a small hole. Just like that this stuff is thick enough or something low pressure like this pool.
How do you repair an Intex inflatable pool?
0:542:40Intex Easy Set Pool Repair Patch Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd algae second cut a round patch and spread cement over the entire patch surface immediately applyMoreAnd algae second cut a round patch and spread cement over the entire patch surface immediately apply the patch over the hole from the inside of the pool. And smooth it down firmly.
Will Gorilla tape patch a pool?
Found a tear in your pool liner? At 4" wide, Gorilla Waterproof Patch & Seal Tape can be used to patch holes, cracks, gaps and tears, even underwater!
Can You Use Flex Seal to patch a pool?
It's inconvenient and pool liners can cost hundreds (sometimes thousands) of dollars to replace. That's why we recommend keeping Flex Tape or our Pool patch and repair kit nearby. The next time you find yourself with this problem, just use Flex Tape and your pool leak will be repaired in a matter of minutes.
What is the best glue to patch a pool?
If your vinyl pool liner needs patching, HH-66 Vinyl Cement is the answer. The world's most effective PVC vinyl adhesive is ideal for mending liner tears, spa covers, and most inflatable vinyl pool toys. It works underwater, sets in minutes, and holds fast even in extreme conditions.
Do you patch a pool from the inside or outside?
Apply one patch inside of the pool surface, smoothing the patch from the center to the outer edges. Repeat the process with the second patch on the outside of the pool surface. Allow the patched area to sit for 10 to 15 minutes, then repeat the smoothing process to ensure a tight bond.
Can you patch a vinyl pool with water in it?
Patching a pool with water in it is a fairly simple process, but keep in mind that a pool liner won't last forever and multiple patches will increase your chances for continual pool leaks. If it's time to repair or replace your vinyl pool liner give Aquaman Leak Detection a call.
Can you patch over a pool patch?
1:016:40How to Patch your Swimming Pool Vinyl Liner! | The Ultimate PatchYouTubeStart of suggested clipEnd of suggested clipSo if all possible if you can patch with vinyl material. It's thicker. And if you can patch withMoreSo if all possible if you can patch with vinyl material. It's thicker. And if you can patch with vinyl material that matches the liner that you're patching. Then it's even better.
Does Flex Seal Spray work on vinyl pools?
0:236:29Flex Seal on A Swimming Pool - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt it all around it read to can two or three times it says good on metal good on water for good onMoreIt it all around it read to can two or three times it says good on metal good on water for good on rubber good on plastic. Right look at this guy's face what'd he lie to you hell no he wouldn't.
Does Flex tape work underwater?
Wet or dry surface, doesn't matter. Flex Tape® works instantly on both. In fact, you can use it underwater too.
How do I fix a hole in my Bestway pool?
Instructions:Clean the area around the puncture.Peel away the backing paper from the adhesive patch, being careful not to touch the adhesive.Apply the patch over the puncture and press firmly.Keep pressure applied for 30 minutes.Adhesive glue should set within 30 minutes, but may take longer in colder water.More items...
How to get cement out of a hole?
Clean around the hole with a cloth. Wipe an area that is approximately 3 inches wider than the hole to remove dirt and contaminants such as skin oils or sunscreen that could prevent the cement from sticking.
Why do pool walls weaken?
However, after years of constant pressure from the water, deterioration due to chlorine and degradation from sunlight exposure, the walls can weaken. Occasionally, there will be something that pokes the side or the bottom of the pool and puts a hole in it.
Can you patch a hole in an above ground pool?
Patch small holes in an above-ground pool with the included patch kit. Most above-ground pools come from the factory with a repair kit in case of damage to the side or bottom of the pool. These pools use a remarkably durable PVC material that is capable of enduring years of water weight pressing against it.
How to seal a pool patch?
Apply a little rubber cement on top of the edge of the patch. This provides an extra seal between the patch and kiddie pool. Allow the rubber cement to fully dry before using the pool. This is usually only a few minutes.
What causes water to leak out of a kiddie pool?
Alcohol swab. Paper towel. A hole in the side of an inflatable kiddie pool can cause air or water to leak out. Two types of leaks can appear in a kiddie pool, a hole in the side being the most common and one that allows water to leak out.
How to remove dirt from rubber cement?
Rub the area around the hole with an alcohol swab to remove dirt and grease that could interfere with the rubber cement bonding.
What is the second type of leak in a pool?
The second type is a hole in the side that allows air to escape, causing the pool to deflate. Both types of leak are repaired in the same manner. Most kiddie pools come with a hole repair kit, but you can use virtually any type of repair kit. Advertisement.
Can you inflate a pool before deflating?
Inflate the pool as much as possible. The patch is not as effective if applied when the pool is deflated. It is fine if some air escapes before the patch is applied. The step does not apply to non-inflatable kiddie pools.
How to clean scratches on steps?
You can also use the denatured alcohol to the clean the steps from any marks or dirt without damaging your steps. Take a fresh rag and pour a very small amount of acetone on it. Using the rag you just poured acetone on, lightly rub it over the area of the step that has scratches (the section you just cleaned).
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
Can pool steps be repaired?
Many times, pool steps become scratched or dirty during shipping or even during the installation process. It is unforeseeable and many times cannot be prevented. Fortunately there is a way to fix many of the small scratches by using common products.
How Do You Fix A Hole Or Crack In A Kiddie Pool?
To fix a hole or crack in a hard-plastic kiddie pool, get some marine silicon or a hot glue gun and seal the crack or hole. Use a card or putty knife to even out the silicon and let dry. A few coats may be needed. Make sure to let it dry after each coat you apply.
How do I patch an inflatable pool?
Steps To Patch An Inflatable Pool: Step 1: Drain The Water. Step 2: Cut The Patch. Step 3: Dry And Clean Patch Area. Step 4: Inflate The Pool. Step 5: Apply Plastic Glue. Step 6: Apply Patch. You may not need to follow all of these steps depending on the type and size of the hole in your inflatable pool. I will go over each of these steps in more ...
What happens if you inflate a patch?
If you apply the patch deflated, and then inflate it, the patch could stretch and pull off easily.
How to use square patch?
If you’re using a square patch, you’ll want to cut rounded edges on each corner. Sharp or angled edges on a patch don’t hold up over time. They tend to peel and pull up after just a couple months. Cut the patch so that at least 2 inches of patch will make contact with the pool material on each side of the hole.
Can you pin point a leak in an inflatable pool?
This technique will actually work for anything inflatable. I’ve used this method on inflatable pools as well as pool toys and floats. It’s a quick and easy way to pin point a leak.
Can you dry an inflatable pool?
This is really not a problem for medium or small inflatable pools, but for the larger pools, this may not work for you. On the larger pools, the inflatable ring is usually above the water line. If that’s the case for you, simply dry the area as best you can.
Does glue hold up to silicon?
The glue may not hold up as long as the silicon, but it will do the trick for next to nothing, if you already have a glue gun.
How to fix a hole in a wall with duct tape?
Place the patch or duct tape, glue-side down, over the hole already covered with a piece of tape, applying even pressure for a minute or so for the glue to set in evenly.
How to fix a leaking float?
Submerge your float in a bathtub or pool and look for escaping bubbles. This will indicate the exact spot of the leak. Another alternative to this is to spray a mixture of water and soap directly on the surface of the float, covering one section at a time . The appearance of soap bubbles will indicate the spot where the hole is. Draw a circle around the hole using a marker or crayon once the float is dry again.
How to fix a leaky duct?
Cut the patch or a piece of duct tape to cover the area of the leak completely, allowing ¼-inch overlay around the edges of the existing temporary patch . This will provide more surface area for it to hold. Cover your hands with gloves to protect your skin and apply super glue to one side of the patch or duct tape, completely covering it in an even layer. Do not glue just the edges as it will leak.
Can you buy new pool toys every time a leak occurs?
Using a few household items and some ingenuity, you can avoid trudging to the store to buy new pool toys every time one springs a leak.
Can you tear an inflatable pool toy?
While everyone is enjoying a dip in the pool on a hot summer’s day, there is nothing like finding a hole in your inflatable pool toy to ruin your fun. Usually made of vinyl, inflatable pool rafts and toys are easy to move around and play with, in the swimming pool, but their lightweight construction and design make them susceptible to tears that can reduce their lifespan.
How to fix a small hole in plaster?
If you’re repairing a small hole, roll the plaster into a ball. Once you’ve molded your plaster, press it down into the cracks or holes. After pressing down your material, take a trowel and smooth out the top of the mix and fill in the surrounding spots of your repairs.
How long does it take to plaster a pool?
Depending on how much of your pool you need to repair, the prepping process can take a long time and might span into a few days or a few weekends if you are a “DIY Weekend Warrior.”. Once the pool is prepped it’s time to mix up your plaster.
Why is my pool blue?
Discoloration or a “bleached out” look is common due to sun exposure or areas of heavy use like the stairs. While the discoloration doesn’t necessarily indicate an issue, it may be time to repair if you want even color.
Why is my pool water rough?
Not only is it annoying to walk across rough patches of plaster, but some spots can become sharp and cause injuries. Every pool owner knows the importance of well-balanced pool water chemistry, but excessive roughness is often related to an imbalance in the water.
What causes stains on pool plaster?
Other factors that can result in staining include organic matter like leaves from a nearby tree.
What to wear when plastering with acid wash?
Since plaster repairs involve chemicals, it is crucial to have goggles, gloves, and face masks to work safely with an acid wash.
What happens if your pool has a low pH?
If your pool has a low pH or calcium level, it dissolves the plaster’s material, and it’s more difficult to fix. Pay close attention to your chemical levels to prevent this damage. As soon as you notice peeling, it’s time to take action.