How to Fix a Hole in a Subwoofer
- Step 1. Remove the casing of the subwoofer speaker. Examine the speaker to find the location of the hole in the speaker...
- Step 2. Cut about 10 pieces of tissue paper into pieces about a half inch bigger than the hole in the speaker cone.
- Step 3. Grab a bowl and dump a significant amount of Elmer's glue into the bowl. Now add water to the...
How do you fix a hole in a speaker?
Now add water to the glue in the bowl until the glue is thin and soup like. Place the 10 pieces of tissue paper into the bowl of diluted glue. Stick one piece or layer of tissue paper over the hole in the speaker and allow it an hour to dry.
How do you fix a broken rubber surround on a subwoofer?
This is especially true if a chunk of the rubber material is completely missing from the rubber surround. In this case, all we need to do is cover up the tear with RTV silicone in order to make the subwoofer almost as good as new — functionally, at least. Unscrew the eight #2 Phillips screws using either a screwdriver or cordless driver.
Can you fix an old subwoofer?
Let’s determine whether we can fix your old subwoofer by familiarizing ourselves with some principals about how the subwoofer works and looking at the parts that make a subwoofer. Then we can go through a quick and dirty checklist, and grab some tools. All speakers do is convert electrical signals to sound.
How do you remove a subwoofer from a car?
Be careful if you use a cordless driver for either screwing or unscrewing — you don't want to strip the screws or the enclosure's holes. You also don't want to accidentally create another hole in the rubber surround with either tool. Use a flat pry tool (such as a flat-blade screwdriver) to prop up an edge of the subwoofer.
Can you fix a subwoofer with a hole in it?
4:2313:47CHEAP FOAM from Walmart | HOW TO Fix a Torn Speaker TutorialYouTubeStart of suggested clipEnd of suggested clipInstead of using some subwoofer surrounds now if ordinarily you could use some scissors. And justMoreInstead of using some subwoofer surrounds now if ordinarily you could use some scissors. And just cut a little piece of this around right off and use it as a patch.
What kind of glue can I use on a subwoofer?
E6000 in the medium viscosity value will be much easier to apply. Both are made by the same company. For foam surrounds, I use Tacky Glue from the craft section of Wal-Mart. I used E6000 on the spider landing and Tacky Glue on the surround landing when I installed my PSI recone.
Why does my subwoofer have holes?
The pressure resisting the movement of the woofer is greater when it is mounted in a box. The smaller the box, the greater the resistance to movement. One way to relieve some of that pressure is by punching a hole in the box. That's the port.
How do you fix a tear in a speaker?
0:201:17Speaker Repair; Torn Surround - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd went right into the speaker surround. So we get to repair that now I am using this LoctiteMoreAnd went right into the speaker surround. So we get to repair that now I am using this Loctite fabric glue. It seems to work pretty well I've heard some people using rubber cement.
Can you use super glue on a subwoofer?
Don't use superglue. It dries extremely hard and brittle. It will crack and break.
How do you fix a ripped subwoofer surround?
0:335:34HOW TO REPAIR A SUBWOOFER SURROUND! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo first of all you're going to identify where the hole is which is just there. And then we're goingMoreSo first of all you're going to identify where the hole is which is just there. And then we're going to flip the sub over go from behind apply some to our fingers.
How do you fix a small hole in a speaker?
Apply a liberal amount of polish along the edge of the hole in the speaker cone. Apply fingernail polish along the edge of the patch. Apply a liberal amount of polish along the edge of the patch. Join the patch material and speaker cone together.
Can you repair a torn speaker cone?
Sometimes it can be possible to obtain and fit replacement cones. If no other method is available one last ditch method to save and repair the loudspeaker that has worked well in the past uses a small patch. Most speaker cones are made of paper, and so a repair using some tissue paper works well.
What can I use for speaker glue?
Permabond 737 is a toughened cyanoacrylate adhesive that is ideal for use in applications regarding the speaker cone, such as surround to cone, cone to spider, and dust cap to cone parts of the speaker.
What kind of glue is used for speaker surrounds?
Get some E6000 or Go2 Glue from Home depot and glue the tear with a very thin layer of adhesive. ^ This. Clear E6000 (it's available in clear and black color) will work great to fix the surround. Be sure to let it cure for 24 hours after the applicaiton and you will be good.
What can I use for speaker glue?
Permabond 737 is a toughened cyanoacrylate adhesive that is ideal for use in applications regarding the speaker cone, such as surround to cone, cone to spider, and dust cap to cone parts of the speaker.
What kind of glue is used for speaker surrounds?
Get some E6000 or Go2 Glue from Home depot and glue the tear with a very thin layer of adhesive. ^ This. Clear E6000 (it's available in clear and black color) will work great to fix the surround. Be sure to let it cure for 24 hours after the applicaiton and you will be good.
Can you glue a subwoofer cone?
2:426:37Repairing a Speaker Cone Using Hot Glue - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just kind of press around the area or just hold the area firm. So that when we press down withMoreAnd just kind of press around the area or just hold the area firm. So that when we press down with the glue gun on this side. It will actually press the two pieces.
What kind of glue is used for speaker boxes?
The best glue for speaker boxes is concrete.
Unscrew the nuts and bolts
The second step is to unscrew the eight Philips or screws, which are on the wheel of the subwoofer. This unscrewing should be done with the help of a flat screwdriver so that it could not form any other chunk or hole in the rubber.
Holding and lifting of car subwoofer by a screwdriver
In this step, the holding and lifting of the subwoofer done with extreme precise care; for this purpose, you can use a flat pray tool that can place underneath the wheel of the subwoofer.
Cleaning of the damaged area
In this step, cleaning should occur. Here cleaning is very important. To clean, use lint-free cloth because it is free from fibers, and it never stuck and left the grains or other threads in the wheel.
Use Nitrile gloves
In this step, you need to prepare yourself for the application of RTV silicone. For this purpose, wear the gloves these gloves can be your favorite gloves, but they should be nitrile gloves. Other gloves can retain and gives some threads, and that is why these threads get stuck in the silicon very much.
Use Cotton swab as RTV applicator
In this step, you need a cotton swab. You can use this cotton swab as an RTV applicator. But as no fiber is allowed in the application of RTV or the repairing, so you can easily remove the upper part, which is the cotton part of the cotton swab.
RTV silicon on the fingertip for inside repair
In this step, the underside damage would repair. For this purpose, take a dap of RTV silicon on the gloved finger. Then apply and rub this finger on the underside damaged area.
Pushing with precise attention and calculated force
In this step, pushing performed and obviously, the pushing method is risk-based, because, during pushing, you can again open the hole and create damage.
How Does A Home Theatre Subwoofer Work?
Let’s determine whether we can fix your old subwoofer by familiarizing ourselves with some principals about how the subwoofer works and looking at the parts that make a subwoofer. Then we can go through a quick and dirty checklist, and grab some tools.
Helpful Subwoofer Fixing Tips – Getting Down To Business
You need to decide now if you are comfortable taking your subwoofer apart. Well not right now! Finish reading this article. Almost everything can be done by anyone with a little patience and help. The help is there for the asking, most Speaker manufactures have Technicians who are happy to help you with the unique troubleshooting for your Sub.
Introduction
I realized — a little too late — that a couple of retaining clips were rubbing against the top of the subwoofer/enclosure in my car. One clip was (thankfully) scratching the subwoofer enclosure carpet, but the other one had poked a hole on the subwoofer's rubber surround.
Step 1 Subwoofer Rubber Surround Repair
Assess the damage. Depending on the severity of the cut, you may need some other scaffolding material (aside from RTV silicone) to enclose the hole.
Step 2
Unscrew the eight #2 Phillips screws using either a screwdriver or cordless driver.
Step 3
Use a flat pry tool (such as a flat-blade screwdriver) to prop up an edge of the subwoofer.
Step 4
Use a clean, lint-free cloth to wipe away any dirt/grease/grime that would otherwise tarnish the bond between the rubber and RTV silicone.
Step 5
Time to get dirty. Put on your favorite brand of nitrile or latex gloves.
Step 6
Cut the end off a cotton swab in order to transform it into an RTV applicator.
shooto
so I punctured one of my speakers with a screwdriver...clean hole about a 1/4" in diameter, mostly in the doped edge of the cone (a tiny bit in the non-doped paper of the cone...it doesn't appear to sound rattle-y like a hole would but I'd like to patch it all the same....what's the best way?
WRGKMC
In the flat area I always use a littel elmers glue and tissue paper. If its on the surround area where it flexes, I use some 100% silicone calk you buy at the hardware store. They even sell it in black. Works good lasts a long time for both repair types. I have some I repaired 25 tears ago and work and sound fine.
Belva
Drx that looks like a viable repair. The only question is how long it will last. Do you plan on finding out or is a recone in the future budget?
WRGKMC
Sorry DR X, Thats was I consider a lesson in how it should Not be done.
Brandenburg
I punctured a speaker ages ago by being careless.. I used elmers glue and it worked fine. I have also heard that fingernail polish works good too.
stratotak
Which is better for tone..1 ply or 2 ply..And does quilted add anything to the tone..lol.
Belva
Which is better for tone..1 ply or 2 ply..And does quilted add anything to the tone..lol.
