Repairing Guides

how to repair a hole in wicker chair

by Kenton Schmitt Published 3 years ago Updated 2 years ago
image

If you have a section on your wicker that's broken, first, use an Exacto knife to cut out the damaged strands. Then, soak replacement reeds in warm water for 30 minutes to make them flexible. Drain the excess water, then weave the new reeds into the wicker pattern.

How do you fix holes in plastic wicker furniture?

How to Fix Faux Wicker Patio FurnitureClean the Faux Wicker Patio Furniture. ... Remove Broken and Frayed Ends. ... Cut a New Resin Strip to Fit. ... Apply a Quick-Set or Non-Quick-Set Epoxy. ... Weave the Strip Into Place. ... Glue the Ends Together Before Trimming. ... Touch Up the Section as Necessary.

Can wicker furniture be fixed?

You fix it of course! Repairing wicker furniture is actually quite easy and doesn't take much time at all. In this guide you'll find easy tips, tools and tricks on repairing everything from your wicker table and chairs, to your sofa and other wicker furniture accessories.

What glue works best on wicker?

Spread a generous amount of wood glue onto the areas where the wicker will be reattached. Use an invisible or clear type of glue. On twisted areas, untwist the wicker slightly so that the glue penetrates between the twisted strands.

How do you fix a hole in the rattan?

Step One: Scrub clean. Using your soap and brush, give the rattan a good scrub. ... Step Two: Clip Off Broken/Damaged Rattan. Using your scissors or wire cutters, trim away any damaged or broken rattan. ... Step Three: Choose and Soak. ... Step Four: Measure and Cut. ... Step Five: Tuck and Glue. ... Step Six: Paint (optional)

Can rattan chairs be repaired?

Not to worry—both wooden and synthetic rattan are easy to repair, and both can be fixed in the same way. If your furniture only has a few loose ends or wrappings, refer to the first method in this guide. If some sections of your furniture need a little extra TLC, skip ahead to the second method.

What material is wicker?

Natural wicker is made from a variety of vines, grasses, and plants. Wicker furniture is sometimes referred to as rattan furniture, but wicker and rattan are not the same things technically. The rattan plant is a commonly used material for wicker furniture.

What is the best glue for rattan furniture?

Ideally, a clear or invisible glue works best on a rattan chair, but if it will be painted later, use a paint-friendly glue. Rattan weave is available at arts and craft stores or at cane and basket supply shops. Choose a weave that matches the color of your original.

What glue will stick rattan furniture?

Step One: Cut out the broken strand(s) of rattan from your furniture and dispose of them. Step Two: Mix the 2-part epoxy resin glue. Step Three: Make sure that the replacement strand of rattan is longer than the strand you have cut out.

How do you fix a wicker peacock chair?

1:072:29Simple Wicker Peacock Chair Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy husband took the wrapping over the part of the arm. You put it in hot water it's going to becomeMoreMy husband took the wrapping over the part of the arm. You put it in hot water it's going to become more flexible. It's going to be a lot easier to work with that's what it was before.

How do you fix a wicker chair back?

0:544:26How to Replace Pressed Cane Webbing - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest way to get the spline out of the groove is to use a caning chisel but you can also useMoreThe easiest way to get the spline out of the groove is to use a caning chisel but you can also use an appropriately-sized chisel or screwdriver. Cut out the middle of the cane.

How do you fix a wicker set?

Use wood glue to fix them. Apply a drop or 2 of wood glue to the bottom of any loose ends that are sticking out. Carefully tuck them back into the wicker pattern by pulling the strands together. Hold down the glued pieces for several seconds to allow them to bond to the chair.

Is wicker the same as cane?

Cane is the thinner material that results from the process of stripping the rattan plant. Wicker can also be made out of rattan, but also out of bamboo, reed, willow, or even synthetic fibers. It can be made from any natural or man-made material that is durable enough to be woven.

How do you fix a wicker set?

Use wood glue to fix them. Apply a drop or 2 of wood glue to the bottom of any loose ends that are sticking out. Carefully tuck them back into the wicker pattern by pulling the strands together. Hold down the glued pieces for several seconds to allow them to bond to the chair.

Can wicker be restored?

When wicker with a clear finish (lacquer, shellac or varnish) becomes dull, you can usually restore its luster by rubbing with a soft cloth dampened with furniture polish or lemon oil. Minor scratches can be disguised by rubbing with a wax-stick scratch remover, available at home centers and some furniture stores.

How do you fix a wicker chair back?

0:544:26How to Replace Pressed Cane Webbing - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest way to get the spline out of the groove is to use a caning chisel but you can also useMoreThe easiest way to get the spline out of the groove is to use a caning chisel but you can also use an appropriately-sized chisel or screwdriver. Cut out the middle of the cane.

How do you fix wicker furniture legs?

Put epoxy glue in each of the drilled holes and insert a 2” piece of 5/8” diameter doweling into the chair leg then push the new piece of leg onto the other end of the doweling. Place a weight on the chair to maintain the pressure on the new joint until the glue has hardened.

How long does it take for wicker to dry?

Avoid touching the furniture for 30 minutes so the glue can fully dry. If you have a section on your wicker that’s broken, first, use an Exacto knife to cut out the damaged strands. Then, soak replacement reeds in warm water for 30 minutes to make them flexible.

How to attach wicker to a chair?

Apply a drop or 2 of wood glue to the bottom of any loose ends that are sticking out. Carefully tuck them back into the wicker pattern by pulling the strands together. Hold down the glued pieces for several seconds to allow them to bond to the chair. Do this for each loose strand you find.

How to fix wicker furniture that is damaged?

2. Soak replacement reeds in warm water for 30 minutes to make them flexible. Select the replacement reeds you need to fix your damaged wicker furniture. Place them in a large container full of warm water. Let them sit in the water for 30 minutes.

How to replace reeds in wicker?

Weave the replacement reeds into the wicker furniture. Thread a replacement reed into the furniture, starting from a point near the back that is less visible. Using pliers or your fingers, gently weave the reed in an out of the wicker. Follow the pattern of the wicker for the best results.

How to clean a reed from a reed?

Remove excess water from the reeds. Remove the reeds from the water and place them on a pile of clean paper towels. Gently press on the reeds with another paper towel to drain out excess water. Continue pressing on them with fresh paper towels until no more water comes out.

How to spray resin on wicker furniture?

Place the wicker furniture outdoors or in a well-ventilated area. Spray a thin layer of resin-based primer over the entire surface of your wicker furniture. Let it dry for 2-3 hours. Hold the can 2–3 inches (5.1–7.6 cm) away from the furniture when spraying it. Wear a mask to avoid inhaling fumes.

How to get loose ends out of wicker furniture?

1. Scan the furniture for loose ends. Examine your wicker furniture to spot any pieces poking out. Do this in a well-lit area, or use a map lamp or flashlight to see things clearly. Use your hands to feel for loose ends in place that you may not be able to examine easily close up.

How to weave a reed?

Its important to remember two things: 1 You will need more length than the linear distance between start and finish of your weave because the weaving action takes up more reed than you might otherwise expect. 2 Leave at least an additional 2 inches excess at the end of each side of the new reed so that it can’t pull out the you put the finished ends tucked under the surface where they can’t be seen.

How to keep a reed in place?

Back out the end of the remaining reed so that the end is aiming down away from the surface. Leave at least 1-2 inches of the original reed tucked down under the surface. To keep a piece of reed in place properly, the more you weave it in the better it holds. So, if you can, try to remove enough original reed so that you can weave back in a pice over and under the cross members at least four to seven times, more if you like. In small areas you may have no other choice but to use a short weave over and under 2-3 cross members. In those cases, you might have to live with it being a little loose when you weave the new piece in. But its perfectly acceptable as long as the woven piece does not fall out.

What material is used to replace wicker reeds?

Wicker can be manufactured using natural or synthetic resin materials. Whether you use natural or resin reed, the style and size of the reed can vary and so can the colors. 3.

Why do you need more length than the linear distance between start and finish of your weave?

You will need more length than the linear distance between start and finish of your weave because the weaving action takes up more reed than you might otherwise expect.

How long do you soak wicker reeds in water?

Note: Natural wicker reed will need to be soaked in water for at least 15 minutes to make it flexible enough to bend prior to weaving. 10. Stain and Seal Natural Wicker. If you are repairing a natural wicker product, you will need to stain or paint it to match your finish.

How to get a replacement reed?

In order to acquire the correct replacement reed, you might need to take a sample from the damaged reed or from a piece of reed that has excess sticking out from a concealed place under the furniture. If you can acquire a sample you can show the vendor, you have a better chance of getting the right replacement or one close enough you can live with from them.

Is wicker reed easy to repair?

If that does not work, you will need to talk to a wicker dealer that can obtain repair supplies. Natural wicker reed is rather easy to acquire whereas resin reed is more difficult because there are so many different vendors with many different types, sizes and colors.

How Can I Repair a Resin Wicker?

To repair your resin wicker furniture, you will need a few tools. You will need new resin wicker strips, manicure scissors or box cutter, and plastic epoxy. Optionally, you will want to match the wicker color with matching paint or spray paint.

What kind of epoxy do you use to glue strips?

Get an acrylic resin to glue the strips, preferable a quick-set plastic epoxy with a precision applicator tip.

Why is plastic wicker furniture durable?

Plastic wicker furniture lasts for a long time because they are durable and weather resistant. If you clean the furniture regularly, it will give you a nice look that outlasts regular wicker furniture. Another benefit is that it is lightweight, making the furniture, like plastic rattan tables and chairs, easy to move.

How to epoxy a weave?

With the help of a paintbrush, apply the epoxy in the empty space and insert the new strip in the weave. Lastly, connect the strips to the epoxy.

What to do if resin strips are loose?

If the resin strips are loose, you can reattach them with glue. You can use resin epoxy.

How to insert a new strip?

To insert a new strip, you will need a resin epoxy. Take a small paintbrush and paint the empty space of the pattern.

How to match furniture color?

Try to match your furniture’s color or you will have to do a touchup with matching paint. Then, you will need a pair of needle-nose pliers. For the finishing touch, you will need a paintbrush and a similar colored paint. Spray paint will also do the job to match your color or redo the color of your furniture.

What to use to protect wicker furniture after cleaning?

Finishing matters. If you aren't applying some kind of varnish or seal to protect your wicker furniture from future damage after cleaning and painting it, Henry says you should start now. "A clear varnish or polyurethane topcoat is the best to use," she says.

How do I paint wicker furniture?

"For raw wicker, I recommend sticking with an oil stain." If you're using spray paint, slowly spray each section of the furniture lengthwise from top to bottom, and allow to dry for 24 hours before spraying on a second, but lighter coat.

What is wicker furniture made of?

Credit: Addie Juell. No matter how well-made your wicker furniture may be, over time it can start to show signs of wear and tear. "Natural wicker is made of one of several plants including rattan, willow, reed , and bamboo ," says Jane Henry of Jane Henry Studios, ...

Is it safe to keep wicker furniture outside?

And while synthetic wicker furniture pieces, as well as ones finished with a waterproof sealant, are okay to keep outside, Henry says that doesn't mean they're safe from effects of the elements. "Sun damage can cause wicker to become discolored and brittle," she explains. " Moisture damage can lead to rotting, and exposure to ...

What is wicker furniture?

What really is “ wicker furniture ” and what all does that word encompass? The word “wicker” is used to describe any woven furniture (or basket) that’s made with pliable materials.

What is wicker baby carriage?

Wicker baby carriage made in a shoe motif. If your wicker repair shop does appraisals ask them what qualifications and certifications they have to back up this service. For a competent and valid appraisal, the person giving it should be a certified antique wicker appraiser.

What is round wicker weave?

Frequently any type of round plant material such as willow or round rattan reed is referred to as having a “wicker weave” though.

What is a wicker chair made of?

This chair is made entirely of wood with a handwoven hole-to-hole cane seat applied to the frame. It is frequently referred to as a “wicker seat” by the general public, but in reality should be referred to as a handwoven cane seat chair.

How long does it take to restore wicker furniture?

It may take days or months to completely restore your wicker piece depending on the severity of the damage, shop scheduling, and other factors. Ask for a receipt, a work order, or job order, something proving you left the item in their care. And also ask for an estimated time of completion and pickup.

What does certification mean for appraisal?

Their certification proves that they have done the research, taken the classes, and passed all the tests, which also means they should be compensated monetarily for their expertise. Also, ask what you will get in return for paying for their appraisal.

Can antique wicker furniture be repaired?

Most antique wicker furniture repair experts will have a few samples of their work or have customer’s pieces with work in process that you can examine.

How do blind canings work?

Blind Caning requires each strand to be measured exactly, cut to proper and exact length, and glued into holes only partly drilled through the framework. These holes are not drilled completely through the frame as are regular cane chair holes. Usually reserved for very fine high-end antique furniture or museum pieces.

What is hickory bark?

Hickory bark is a seasonal available material and much more costly to obtain than the other weaving materials.

What is paper rush?

Paper Rush is a continuous strand of man-made paper material, forming a distinct pattern of four large triangles, meeting in the center. This weave is commonly found on post-1910s Colonial ladderback chairs.

What is a porch cane?

Two layer weave applied to both the top and bottom around seat rails, creating a pocket. Frequently seen in seats and backs of porch rockers and is weather resistant, hence the name “Porch Cane.” Can also be done in Diamond Weave, Basket Weave, or Chevron.

Where are holes drilled in a chair?

Holes are drilled around the perimeter of chair seat frame and individual strands of cane are hand woven through the series of drilled holes.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9