If your chainsaw is a Homelite, the repair is uncomplicated, because the starter housing is connected to the engine by screws that are easy to find and remove. If the cord slipped out of the track, then rewinding it should restore the operation of the starter. If that doesn't work, though, you may need to replace the spring.
Full Answer
How do you fix a Homelite chain saw?
Homelite Chainsaw chain brake was not releasing. This was my fix for the issue. I'm not a professional. Please take your saw to a pro if your not comforta...
What is the correct way to start a Homelite chainsaw?
- Bare hands Step-by-step Procedures
- Step I: Activate the chain brake Before commencing the starting process, be certain to activate the chain brake. ...
- Step II: Press the decompression controls Some models of these chainsaws have decompression controls. ...
How to troubleshoot a Homelite chain saw?
Reasons for a Homelite Chainsaw Not Starting
- Fuel System. The most common problem associated with nonstarting two-cycle chain saw engines is old, stale fuel. ...
- Clearing Flooding. Address flooding by draining out the fuel in your engine’s tank. ...
- Check for Spark. Check for spark with the spark plug out of the engine. ...
- Reassemble Engine. ...
How to fix a pull rope on a Homelite chainsaw?
How to install or replace the pulling rope
- Step one
- Step two
- Step three
- Step four
- Step five
- Step six
- Step seven
- Step eight
- Step nine
- Step ten
How do you disassemble a Homelite chainsaw?
5:4713:23Homelite Chainsaw Disassembly – Chainsaw Repair Help - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo access and uninstall the carburetor first remove the top. Cover. Now detach the carburetor fuelMoreTo access and uninstall the carburetor first remove the top. Cover. Now detach the carburetor fuel line from the primer bulb be prepared for some fuel to spill. Next unhook the choke lever.
How do I clean the carburetor on my Homelite chainsaw?
3:306:19Homelite Chainsaw Repair and Carb Cleaning - YouTubeYouTubeStart of suggested clipEnd of suggested clipOut. With carb cleaner. Inside that big hole right there there's a little screen as long as you canMoreOut. With carb cleaner. Inside that big hole right there there's a little screen as long as you can see through that screen that it's fine but this can get really gummed up and nasty.
How do you adjust the carburetor on a Homelite chainsaw?
0:413:54HOW TO ADJUST the Carburetor on the Homelite Timberman ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this is the high screw. And this is your idle adjustment screw here. So first you would adjustMoreAnd this is the high screw. And this is your idle adjustment screw here. So first you would adjust your carburetor. Then turn this in to make it idle faster or turn it out to make it idle slower.
How do you disassemble a chainsaw?
0:193:40Echo Chainsaw Disassembly – Chainsaw Repair Help - YouTubeYouTubeStart of suggested clipEnd of suggested clipStarting set the chainsaw on its side and remove the screws securing the recoil starter assembly toMoreStarting set the chainsaw on its side and remove the screws securing the recoil starter assembly to access the recoil pulley start a rope and rewind.
Can you clean a chainsaw carburetor without taking it apart?
Alternatively, you can also clean the carburetor by blending some carburetor cleaner with the gasoline and running your chainsaw at a slow speed. You can also use a cleaner, such as aerosol B12, to clean the pilot air jet. 4 Cleaning a Carburetor Without Opening/Removing It.
Why does my chainsaw dies when I give it gas?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
Why does my Homelite chainsaw won't stay running?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Why does my chainsaw start and then stop?
0:052:01Top Reasons Chainsaw Starts, Then Stalls - YouTubeYouTubeStart of suggested clipEnd of suggested clipOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall.MoreOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall. You can try cleaning the arrestor with a wire brush. But you may need to replace it with a new one.
What are the L and H screws on chainsaw?
However, if you have an older saw, here's how to quickly tune it yourself. Start by locating the three adjustment screws. They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
How do you troubleshoot a chainsaw?
0:442:20Top Reasons Chainsaw Won't Start — Chainsaw TroubleshootingYouTubeStart of suggested clipEnd of suggested clipOld or bad fuel can also create a clog in the fuel filter which can prevent the chainsaw fromMoreOld or bad fuel can also create a clog in the fuel filter which can prevent the chainsaw from starting we recommend replacing the filter with a new.
How do you fix a chainsaw?
0:396:13Chainsaw Wont Start? Chainsaw Repair How To - GardenForkYouTubeStart of suggested clipEnd of suggested clipYou want to open up your fuel. Here suck out all the gas. It's in actually the gas oil mixture takeMoreYou want to open up your fuel. Here suck out all the gas. It's in actually the gas oil mixture take this all out put it into a gas safe container. Then get yourself something that measures clearly.
How do you rebuild a chainsaw?
0:006:38Engine Rebuild On Husqvarna 55 & 51 Chainsaw Part 1/3 - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing I'm going to do is remove the two half-inch nuts here and remove the barn. Chain. JustMoreFirst thing I'm going to do is remove the two half-inch nuts here and remove the barn. Chain. Just bring the bar up like that. Get the chain off the tip of the bar.
How do you adjust the carburetor on a Homelite Super 2 chainsaw?
23:0828:58Homelite Super 2 Chainsaw - Carburetor Rebuild and TuneupYouTubeStart of suggested clipEnd of suggested clipSo that this chain just starts to move. And once I find that point I'm gonna start adjusting the lowMoreSo that this chain just starts to move. And once I find that point I'm gonna start adjusting the low-speed jet which on this carburetor is the one closest to the engine.
What is the fuel mixture for a Homelite Super 2 chainsaw?
Engine oil should be mixed with gasoline at a specified ratio before fueling the machine. When refueling with Homelite oil, mix oil with unleaded gasoline at a ratio specified on the container. For other two-stroke engine oils, Homelite recommends mixing one part oil with 16 parts gas.
Are Homelite chainsaws any good?
The Homelite brand has a reputation for delivering affordable, functional tools with average homeowners in mind. This is on full display with the Homelite UT43122B electric chainsaw. It's a good choice for occasional use and can handle pretty much any cutting job that's likely to pop up around the yard.
How do you adjust the carburetor on a Homelite Super XL?
4:1122:02Tuning a Chainsaw By Ear...Homelite Super XL Test Subject - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn carburetors you want to remember too rich in it up. You go counterclockwise to lean it out you goMoreOn carburetors you want to remember too rich in it up. You go counterclockwise to lean it out you go clockwise. So if it's way too rich. You want to lean it out a little bit and go clockwise.
How to fill a Homelite XL chain saw?
1. Check the oil reservoir to ensure that there is oil in the tank that feeds the automatic oiler. If the tank is empty or low, fill the tank with Homelite Bar and Chain Oil for the best results. Fill only to the fill line. The Homelite XL chain saw is designed to use one tank of oil per each tank of fuel. Fill the oil reservoir each time you fill ...
How to remove a chain from a saw?
Push the yellow chain tensioner knob in and turn it counterclockwise to release and remove the chain cover, and gain access to the bar and chain. Push the guide bar toward the saw, and remove it and the chain. Clean the groove and channel with a stiff-bristled brush.
What to do if you have too much oil on a chainsaw?
When you notice too much or too little oil on the chain, stop cutting immediately, and diagnose and fix the problem. Cutting wood with too little lubrication on the chain saw chain can be detrimental to the saw and can pose safety risks to you.
Where is the oil adjustment screw on a chainsaw?
The screw is located on the bottom of the chain saw and increases or decreases the oil output in relation to the adjustment. Before adjustment, start the chain saw and allow the engine to run for a couple of minutes.
Does the Homelite XL chain saw have an oiler?
Even though the Homelite XL chain saw is an older model machine, it still comes equipped with an automatic oiler that disperses oil from the tank to the channel and groove in the guide bar, and ultimately to the chain. When you notice too much or too little oil on the chain, stop cutting immediately, and diagnose and fix the problem.
MORE COMING SOON!
Homelite's paint colors have changed a number of times since the 20MCS went into production in 1953. There are 3-4 shades of red that we have all seen, 2-3 shades of metallic blue, a metallic medium green, plus the white & black accents.
The above photo shows a NOS Homelite throttle handle cover with the "red-orange" tinge, a drivecase cover with the deeper powercoat red and a fan housing that I repainted using Duplicolor GM Victory Red. It took a low-light photo to show the subtle differences
The same parts in better lighting look nearly the same. So be careful to judge paint colors in person whenever possible...photos can be deceiving.
