Open the door of your Hotpoint dryer, and locate the screws that hold the lid down. Use your screwdriver to remove all screws that hold the lid in place. Open the dryer lid. On a new-style Hotpoint dryer, you do this by flipping open the hinged lid. Note that only the front part can be lifted up.
Full Answer
How to fix Hotpoint dryer?
Common solutions for: Hotpoint Dryer overheating
- 01 - Heating Element. The heating element warms the air before the air enters the dryer drum. ...
- 02 - Heating Element Assembly. The heating element warms air as it passes over the element. ...
- 04 - Cycling Thermostat. The cycling thermostat cycles the heat on and off to maintain the proper air temperature. ...
- 05 - Felt Seal. ...
- 06 - Blower Wheel. ...
Why is my Hotpoint dryer not heating?
Why is my Hotpoint tumble dryer not heating up? If your dryer isn't heating up, or is blowing cold air, it's probably down to either the heating element or the thermostats. And a safety thermostat, this will open if the temperature gets too hot to prevent damage but will not reset when cold. The other cause of a cold dryer is a faulty element.
Why is my Hotpoint washing machine not spinning?
Why Is My Washing Machine Not Spinning
- Drain pump blockage. One of the most common reasons why your washing machine has stopped spinning is when it can’t drain properly due to a blocked drain pump.
- Imbalanced drum. When the load is too heavy for the machine, or sometimes if you are trying to wash one large item on its own, the appliance detects a risk.
- Motor brushes worn out. ...
Why is my gas dryer not heating up?
– Top 7 Causes and Solution
- Faulty Gas Valve Solenoid Coils. Have you ever wondered how a gas dryer works? ...
- Blown Thermal Fuse. If the thermal fuse in your gas dryer blows, you can replace it and your dryer will be as good as new!
- Faulty Igniter. ...
- Defective Flame Sensor. ...
- Defective High Limit Thermostat. ...
What causes a Hotpoint dryer to stop working?
Check the dryer belt to determine if it is broken. If the belt is broken, replace it. If you have a gas dryer, unplug the dryer from the wall and plug something else into the outlet to determine if the outlet is working. If you have an electric dryer, check the home circuit breaker or fuses.
How do you troubleshoot a Hotpoint dryer?
0:161:54Hotpoint Dryer Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipLook at the drive belt to make sure it is not loose or broken examine the idler pulley for signs ofMoreLook at the drive belt to make sure it is not loose or broken examine the idler pulley for signs of wear replace any parts that appear to have a problem and press the top panel back onto the dryer.
Why is my Hotpoint tumble dryer not working?
We recommend the following: Ensure that the vent hose is not blocked or crushed. Ensure that your Hotpoint tumble dryer is not being overfilled with clothing as this will impair the performance. Double check the heat switch on your dryer is set to the appropriate position.
Where is the fuse located in a Hotpoint dryer?
5:095:45Hotpoint dryer won't turn on - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis right here where to get the fuse. Down below in the description. Box you pretty much get it offMoreThis right here where to get the fuse. Down below in the description. Box you pretty much get it off amazon. And you can use it to replace the fuse in your dryer. There's two indicator that lets you
How long should a Hotpoint tumble dryer last?
Around 10 to 15 YearsTumble Dryers Should Last for Around 10 to 15 Years One of the simplest appliances in your home, a well maintained tumble dryer should last for around 10 to 15 years (Daily Finance).
How do I reset my Hotpoint tumble dryer?
You'll find that your Hotpoint Aquarius tumble dryer reset button will either be red with a reset logo which can simply be pressed to actually reset the appliance, or there will be a small hole on one of the thermostats near the heater. You'll need a pin to perform the reset if this is the case.
How do I reset my dryer?
Many dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.
How do you take apart a Hotpoint dryer?
0:303:19GE Dryer Disassembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour first step is to remove the screws at the rear of the control panel to release. It. Next openMoreYour first step is to remove the screws at the rear of the control panel to release. It. Next open the dryer door and remove the screws inside the door frame which secure the main.
Why is my Hotpoint dryer not heating?
If your dryer isn't heating up, or is blowing cold air, it's probably down to either the heating element or the thermostats. Most dryers have a cycling thermostat that controls the temperature by opening and closing repeatedly.
How do I know if my dryer fuse is blown?
1:042:10Dryer Not Heating? Thermal Fuse Testing, Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the needle does not move or the digital display does not change significantly. There is noMoreIf the needle does not move or the digital display does not change significantly. There is no continuity. Which means the fuse has blown out and will need to be replaced.
What happens when thermal fuse blown on dryer?
When it blows, the dryer stops generating heat. It's necessary to replace it before the dryer will run again. The thermal fuse is different from the thermal cutoff. The thermal fuse stops the dryer from operating, tumble and heat included.
How do you troubleshoot a dryer that won't start?
Unplug the dryer and check the thermal fuse for continuity. Replace the thermal fuse if the multimeter measures no continuity. Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to-start switch can prevent the motor from running.
How do I reset my thermal fuse?
Step 1: Locate the Fuse. Study the owner's manual for the location of the thermal fuse. ... Step 2: Cut Power to the Dryer. ... Step 3: Disassemble as Needed. ... Step 4: Disconnect the Thermal Fuse. ... Step 5: Conduct a Continuity Test. ... Step 6: Purchase a Replacement. ... Step 7: Replace the Fuse. ... Step 8: Reassemble the Dryer and Test It.
Why won't My Hotpoint dryer heat up?
If your dryer isn't heating up, or is blowing cold air, it's probably down to either the heating element or the thermostats. Most dryers have a cycling thermostat that controls the temperature by opening and closing repeatedly.
Do all tumble dryers have a reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.
Why are all the lights flashing on my Hotpoint tumble dryer?
Hotpoint tumble dryer all lights flashing When multiple lights are flashing on your tumble dryer and you're unable to select a programme this indicates a software fault and you'll need to contact a service engineer.
Why does my dryer stop mid cycle?
If the drum bearing is worn out, it may put too much strain on the motor, causing the dryer to stop mid-cycle or not turn at all. To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand. If the drum rotates freely, it is unlikely that the drum bearing is worn out.
What happens if the drum glides on a dryer are worn out?
If the drum glides are worn out, the drum can start binding and put strain on the motor. If this happens, the motor shuts down, preventing the dryer from turning. To determine if the drum glides are worn out, inspect them for wear. If one or more of the... glides are worn out, replace all of the glides as a set.
How to tell if support rollers are worn out?
To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not... rotate freely, check the support rollers for wear. If the rollers spin freely without wobbling, they do not need to be replaced.
How many rollers does a dryer have?
Most dryers have two drum rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly.
What does a drum bearing do on a dryer?
The drum bearing supports the rear of the dryer drum. Over time, this bearing wears out. If the drum bearing is worn out, the dryer may not turn properly. To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand.
How to fix a humming motor?
First, check the motor to see if it makes a humming noise. If the motor still hums, remove the belt from the motor and check the blower wheel to ensure that it is not obstructed. Next, with the belt removed, try rotating the drum by hand. If the drum does not rotate freely, determine what is causing the drum to bind.
What to do if you suspect a motor is at fault?
If you suspect the motor is at fault, replace it.
What happens if a dryer belt breaks?
On most dryers, when the dryer belt breaks, the motor will still run, but the drum will not turn. However, some dryers have a switch that shuts off power to the dryer if the drive belt is broken....
How to check if dryer motor is defective?
The drive motor turns the drum and the blower wheel to exhaust the air. Before replacing the motor, first check the thermal fuse , start switch, and door switch. If all of these parts are working properly, but the motor is making a humming noise, remove the belt from the motor and check the blower wheel for obstructions. If the blower wheel is clear of obstructions, the dryer motor might be at fault. If you suspect the motor is defective, replace it.
How to tell if dryer door switch is working?
To determine if the door switch is working, try starting your dryer and then listen for the “click.” If the door switch makes a clicking sound, it is probably not defective. If you don’t hear a click, use a multimeter to use the door switch for continuity. If the switch does not have continuity, replace it.
How to check if a gas dryer is working?
If you have a gas dryer, unplug the dryer from the wall and plug something else into the outlet to determine if the outlet is working. If you have an electric dryer, check the home circuit breaker or fuses. If the circuit breaker or fuses are working, use a multimeter to test the outlet.
What does the door switch do when the dryer is closed?
The door switch activates when the dryer door is closed. On most dryers, the door switch makes an audible clicking sound when it activates. To determine if the door switch is working, try starting...
What to do if dryer doesn't heat?
If the dryer doesn’t heat, the timer might be defective. However, this is very rarely the case. Before replacing the timer, check all the more commonly defective parts. If you determine that all of the other components are working properly, test the timer by using a multimeter and consulting the wiring diagram.
How to tell if a dryer heating element is out?
To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it.
What does an igniter do on a dryer?
03 - Igniter. The igniter uses heat to ignite the gas in the burner assembly. If the igniter is not working, the gas will not ignite, preventing the dryer from heating. To determine if the igniter has burned out, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it.
How to check if flame sensor is defective?
To determine if the flame sensor is defective, use a multimeter to test the sensor for continuity at room temperature. If the flame sensor does not have continuity at room temperature, replace it. Required Part.
How many solenoid coils does a gas dryer have?
Gas dryers have two or more gas valve solenoid coils. The gas valve solenoids open the gas valve ports to allow gas to flow into the burner assembly. If a gas valve solenoid fails, the dryer won’t heat. To determine if one or more of the gas valve solenoids has failed, check the igniter.
How many volts does an electric dryer need?
Electric dryers need two legs of 120 volts AC equaling 240 volts. It is not uncommon for only one fuse or breaker to trip resulting in the dryer able to run, but not heat. The fuse box or circuit breaker should be checked or voltage measured at the outlet using a multi-meter.
Can a high limit thermostat shut off a dryer?
If the high-limit thermostat is malfunctioning, it may shut off the burner even if the dryer is not overheating. However, this is rarely the case. Before replacing the high limit thermostat check all the more commonly defective parts.
How to get a better view of a hotpoint dryer?
On newer Hotpoint dryers, you get a better view from the side by pushing the cabinet's side panels. Look approximately six inches from the base on the cabinet's right and left sides. You should see two screws. Unfasten them with a Phillips head screwdriver.
How to move the front panel off?
Slide the front panel off. On old-style models, it can move to the right. On new-style models, it slides to the left.
Can you take a Hotpoint dryer apart?
Warning. Always switch your Hotpoint dryer off, and unplug it before taking it apart. Check your warranty before servicing your Hotpoint dryer. Even the most reliable appliances need servicing from time to time. Whether you're looking to fix a broken belt or investigating a mysterious sound, your Hotpoint dryer can be closely checked.
