- Ensure you have enough replacement cord in the correct color (click here to learn how to order cord), replacement washers and a threading needle. ...
- After uninstalling the shade, remove and set aside the breakaway cord connector. You can cut the lift cords, as they will be replaced anyway. ...
- Remove the plugs on the bottom rail by prying up.
How much does it cost for Hunter Douglas blinds?
With this in mind, how much do Hunter Douglas blinds cost? Hunter Douglas blinds cost $300 for a standard size window, and they charge $20-$36 per square foot. You can expect to spend an extra $50 or more if you choose light-diffusing Hunter Douglas blinds.
How do you remove Hunter Douglas blinds from brackets?
How do you remove Hunter Douglas roller shades?
- Pull on the cord to raise the blinds all the way up.
- Loosen the tab screws located on the bottom of each mounting bracket.
- Tilt the back of the headrail downward, then slide the headrail out of the bracket.
- Pry the cord lock cover and the cord lock out of the headrail with a flat-head screwdriver.
How sturdy are Hunter Douglas blinds?
Under their vertical blind selection, they offer the following products at the time of this writing:
- Skyline
- Cadence
- Somner
- Vertical Solutions
How to reset your Hunter Douglas Powerview motorized blinds?
- Press and hold the manual button on the headrail gently for 6-10 seconds. When the shade jogs, immediately release the button. I suggest turning off all noise in the room. ...
- Watch the shade go completely up and down while it sets new limits.
- Repeat as necessary.
See more
How to send Hunter Douglas blinds to repair?
If you send your blinds to Hunter Douglas repairs, send them via certified or return receipt mail. Return receipt mail will help ensure your blinds are not misplaced on their way to the repair facility. Any damage caused by normal wear and tear is not covered by the Hunter Douglas warranty.
What to do if Hunter Douglas blinds are missing slats?
If you are missing slats or unable to open your Hunter Douglas blinds, contact the company and arrange for repair. Hunter Douglas blinds come with a lifetime warranty, and you should take them to Hunter Douglas professional for no-cost repairs. If you have a minor repair, such as malfunctioning cord, you can replace and fix this yourself.
How to redeem Hunter Douglas blind warranty?
Contact the place where you purchased your Hunter Douglas blinds to redeem your warranty. If you cannot remember where you purchased your blinds, contact Hunter Douglas directly at 800-789-0331. They will register your warranty and start the repair process.
How to reattach washers to string?
Reattach the washers to the end of the string by sliding them on the end of the string and tying them in place with a double knot. Thread the other end of the strings through the eye of a restring needle. Tie a single knot to secure.
How to put cord guides on a blind?
Set the cord guides over the three string holes at the top of the blind, making sure the cord runs horizontally down the right side of the blind. Slide the head rail cover in place over the strings and cord guides. Return the end cap to the upper right-hand side and gently push it into place.
How to remove strings from blinds?
Remove the strings from your shades. Save the three plastic cord guides along the head rail for later use. Remove the strings from the cord lock. Save the small plastic cord stop assembly in the cord lock for later use. All the strings have now been removed from the blinds.
How to raise blinds to the top?
Raise the blinds to about 6 inches below the top slat, or head rail. Place your thumbs at the bottom of the head rail toward the window side. Press upward with your thumbs and pull downward on the top front as you rotate it toward the room side. The blinds are now released from the spring brackets.
What kind of blinds do Hunter Douglas have?
These instructions focus on Hunter Douglas' Crosswinds wooden vertical blinds, though you should be able to adapt them for different blinds.
What to do if your blinds won't open?
Open the blinds. If the blinds won't open, note where they stop. If there is something preventing them from opening, focus on that.
What to do if tension cord is broken on blinds?
If the tension cord was not installed properly or if it is broken, the pulley won't rotate and the cords won' t be taut. Reset the cord tensioner. Make sure there is no excess cord. If there is, simply cut it. Note that the blinds must be in the closed position to do this properly.
How to fix a vane clip?
Fix the vane clips. The clips that hold the vanes should be numbered and in numerical order, and the numbered side of the clip should face the room. There is a slot between the long and short prongs of the clip, and it should face you. The vanes should be snapped into place--make sure there aren't any loose vane clips.
How to remove a vane?
If it is necessary to remove a vane, first push up on the vane. Gently open the vane hook by inserting a credit card-sized piece of rigid plastic between the vane and the long prong of the vane hook. Then you can carefully remove the vane.
How to remove plastic end cap on track?
Use a small Phillips head screwdriver to remove the screws securing the decorative plastic end cap to the control side of the track.
How to release mounting base?
Release the mounting base by rotating the base 45 degrees.
Can you change a vertical track to a split draw?
Due to internal components, the type of vertical track on a product cannot be altered after production and cannot be changed from a one-way track to a split draw or vice versa. If a new track is ordered, you may need to order one or two additional vanes as well.
How long should the operating cord be for a blind person?
Child safety recommendations state that all operating cords should be 40% the total length of the blind or less.
How to remove tilt mechanism from headrail?
Slightly spread the headrail, and remove the tilt mechanism by lifting it up and out of the headrail.
How to remove stiffeners from headrail?
With pliers, remove the rail stiffeners that are pressed into both ends of the headrail.
Can kids strangle cords in blinds?
Kids can strangle in blind cords. To make your blinds safer for kids, keep cords out of reach and secure cord and bead chain loops. To learn more, please visit our child safety guide.
