how to repair a large drywall hole

Fix Large Holes

1. Cut Out a Piece of Drywall to Use as the Patch. Cut a piece of drywall into a square a little bit bigger than the hole.
2. Trace the Patch Size Over the Hole
3. Cut Out the Hole
4. Attach Furring Strips Inside the Hole
5. Attach the Patch to Furring Strips
6. Apply Joint Tape to the Patch
7. Apply Joint Compound. ...

Full Answer

What tools are needed to fix a hole in drywall?

Other Tools That Are Nice to Have:

• Keyhole Saw
• Drywall Screw Gun
• Cordless Drill
• Drywall T square
• Rasp
• RotoZip ®
• Ten Inch Drywall Knife
• Halogen Light
• Sanding Pole

How to finish drywall in 9 steps?

Instructions

• Prepare the Surface. ...
• Apply the First Mud Coat (Paper Tape) If you are using paper tape, it must be embedded in a layer of compound, and thus the process takes slightly longer than ...
• Apply the First Mud Coat (Fiberglass Tape) Fiberglass-mesh tape is self-adhesive and can be applied directly to the drywall seams without first applying a layer of mud.

More items...

How much does drywall repair cost for small holes?

To estimate costs for your project:

1. Set Project Zip Code Enter the Zip Code for the location where labor is hired and materials purchased.
2. Specify Project Size and Options Enter the number of "items" required for the project.
3. Re-calculate Click the "Update" button.

How to patch small holes in drywall?

Attach a small piece of wood, known as a furring strip, vertically inside the cut-out hole using a drill and drywall screws. Screw the furring strips into the existing drywall. Between the two existing studs and the furring strip, the new drywall will have plenty of support to avoid cracking.

How do you fix an extra large hole in drywall?

2:286:57How to patch and repair drywall - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut a square in the wall around the hole drywall can be found in two by two foot pieces. So weMoreCut a square in the wall around the hole drywall can be found in two by two foot pieces. So we traced that and cut a 2 by 2 foot square. If your hole is smaller cut down your drywall piece to fit use

How do you repair a large hole in the wall?

InstructionsPrepare the Opening. Trim the edges of the hole to create straight sides and a square or rectangular overall shape. ... Install the Backing Strips. ... Install the Drywall Patch. ... Tape the Seams. ... Mud the Seams. ... Sand the Mud. ... Prime and Paint the Patch.

How do you fix a 6 inch hole in drywall?

2:5815:38How to Fix Holes in Drywall - 4 Easy Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that's option number one for your first coat option number two is what's called the presto patchMoreSo that's option number one for your first coat option number two is what's called the presto patch the presto patch is a really simple idea basically it's a four inch circle of half inch drywall.

How big of a hole can you fill with joint compound?

Preparing the Drywall Area. Use spackle to repair holes less than 4 inches (10 cm) in diameter. Spackle can be used to repair holes up to the size of your hand. You will have to use a support like mesh or wire to repair holes larger than 4 inches (10 cm) in diameter.

How big of a drywall hole can you patch?

6 inchesFix Large Holes For holes larger than 6 inches, you'll create a drywall patch with a different attachment method for the repair.

What size hole is too big to patch?

Puncture repairs are limited to the crown area of the tire, which is the center of the tread approximately 1 to 1.5 inches in from each shoulder. Puncture repairs are also restricted by size and cannot be larger than 3/8 of an inch in diameter.

How do you fix a big hole in drywall without a patch?

Tiny nail and screw holes are the easiest to fix. Use a putty knife to fill them with spackling or wall joint compound. Allow the area to dry, then sand lightly. Anything larger must be covered with a bridging material for strength before patching compound can be applied.

What is a California patch?

0:182:15How To Repair a Drywall Hole Using the California Patch - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe no cladding patch is known in some areas as the California patch. It doesn't require a backing.MoreThe no cladding patch is known in some areas as the California patch. It doesn't require a backing. And it works great for holes approximately.

What household items can I use to patch a large hole in the wall?

Mix a tablespoon of flour, a teaspoon of salt and a few droplets of water in a small container. Mix thoroughly until it forms a paste and apply to the hole or crack as you would joint compound. Use a putty knife or index card to remove the excess while it is still wet and allow the rest to dry.

How to repair drywall: small holes, cracks, and dents

If that heavy picture pulled your screw through the drywall or years of old nail holes are starting to build up, give them a quick touch-up using just a few, inexpensive tools.

How to repair drywall: medium-sized holes

For holes that are under four inches in diameter but too large to fill with spackle, use a drywall repair kit. These kits typically include all of the tools you’ll need to complete the repair on your own.

How to repair drywall: large holes

For larger holes in your drywall that are bigger than four inches in diameter, you won’t be able to use putty or spackle to repair them. When repairing larger drywall holes, you’ll likely need to cut out some of the existing drywall. For this step, be cautious and avoid cutting any wires that run behind the walls.

Small Dents and Dings

Scrape away loose debris from the hole. Cover the hole or dent with fast-drying spackle to bring the spackle level with the drywall surface and let it dry 24 hours -- or the time recommended by the manufacturer’s instructions. Sand smooth.

Popped Nail Heads

A popped nail isn't holding in the stud and backs out of the drywall, creating a popped nail head.

Small Holes

For small holes, like those created by a doorknob, a patch kit may be used.

Large Holes

For holes larger than 6 inches, you'll create a drywall patch with a different attachment method for the repair.

Corner Bead Patch

Corner bead is used where two pieces of drywall meet to form a corner. Corner bead is available in a variety of materials, including metal, paper and vinyl.

Finish the Repair

You're almost done. Here's where you make it look like nothing happened.

Repair Textured Drywall

Textured drywall is a bit more complicated, but still pretty simple to repair.

Why do drywall screws pop up?

But drywall screws sometimes pop up too, as a result of damp framing that dries out and shrinks during the first year or two in new construction. The first step of how to patch a small hole in the wall is to drive nails back down using a nail set.

How to get a hump out of tape?

Squeeze some, but not all, of the compound out from under the tape so you don’t create a big hump on the wall. Immediately apply a light coating to the topside of the tape, tapering it out onto the wall.