- Take Apart Your Drill. This part is simple just remove the screws (save them!) and separate the two pieces of your drill carefully.
- Cut the Wire Between the Trigger and the Battery Terminal. ...
- Cut the Plug Off of Your Transformer and Strip Wires. ...
- Splice the Wires. ...
- Reassemble Drill. ...
- Test. ...
How do I Fix my cordless drill that won't hold bits?
Refer to your owner's manual for advice tailored to your model. When the chuck won't hold bits in your cordless drill, check the following parts: the drill chuck, ball bearing, key, and chuck screw. Use our repair troubleshooting guide to walk you through your own repair, and have your cordless drill up and running in no time.
What kind of tools does Makita make?
INNOVATION Technology Engineered by Makita Corded Corded Corded Power Tools Concrete & Masonry Tools Drills & Fastening Dust Extraction Grinding, Sanding & Polishing Multi-Tools Outdoor Power Equipment Saws Specialty Specialty Cutting Tools Wood Surfacing & Fine Finishing Solutions Rule The Outdoors Cordless Outdoor Power Equipment
Does direct repair offer free shipping to Makita factory service centers?
Direct Repair offers free “roundtrip” shipping to and from a Makita Factory Service Center, with easy online access to process a repair request and access status notifications. click here 1. Search near your area
What should I do if my cordless drill motor gets hot?
If the motor gets hot in your cordless drill, check the following parts: carbon brush, armature, holder, and bearing. Once you have determined the part that is causing the issue, read our repair tips to help complete the repair yourself. You might be surprised how easy it is to fix. Check your owners manual for detailed instructions for your model.
Can a Makita drill be repaired?
Makita will offer a 3-day turnaround on repairs for the XRT01 done through the Fastlane program. This service is available to all XRT01 owners, in the contiguous 48 states, at no additional cost at Makita's Factory Service Centers.
Why has my cordless drill stopped working?
The battery near the end of its life will not hold as much power and will require to be charged more frequently, eventually dying out. When this occurs, purchase a new battery. The brushes provide the electrical current to the armature by riding on the commutator.
Why does my Makita drill keep stopping?
If it's a corded drill, that's a common sign that the cord is going bad and it's time to replace it. It might also be the power switch (see below). If it's a battery drill then look to the power switch. Dirty contacts will cause intermittent power loss.
How do you fix a drill that won't spin?
0:061:00Is your drill not spinning? - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnly to have no spin don't go no work today. Simple solution you can bring it down to us we canMoreOnly to have no spin don't go no work today. Simple solution you can bring it down to us we can check it out for you find out what the problem is or. You can see if it slipped into neutral.
How do you service a cordless drill?
How Do You Maintain a Cordless Drill?You need to oil it regularly, clean off the debris after each job, and make sure that you're always keeping the batteries charged. ... Also read: How To Keep Tools From Rusting.Another suggestion is to keep your tools separated from each other.More items...
How do you fix a battery drill?
0:333:07How To Fix A Cordless Drill Battery That Won't Charge - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo once you get these to where each one is touching. The positive the positive negative to negativeMoreSo once you get these to where each one is touching. The positive the positive negative to negative just let it sit for five minutes. And.
How do you rebuild a Makita drill?
2:364:20Makita Hammer Drill Repair - How to Replace the Gear AssemblyYouTubeStart of suggested clipEnd of suggested clipNow line up the gear on the motor with the gears on the gear assembly. Press the two together. And.MoreNow line up the gear on the motor with the gears on the gear assembly. Press the two together. And. Now place the gear assembly. Back into the motor housings.
What is the common cause of breakdown of electric drill?
Possible Reasons for a Defective Power Drill Claim Unsafe design/design defects. Lack of proper safety guards. Improper warning provided. Manufacturing flaws.
What does it mean when Makita drill light flashes?
If the battery lights begin to flash red, the battery is too hot to charge.
Why is my drill not moving?
The most common reason a drill doesn't spin straight is that the drill bit is not properly centered in the chuck. Be sure the drill bit is fully inserted into the center of the chuck, and is not clamped off-center.
Why is my drill not drilling?
Dying Batteries Weaken a Drill Charge your battery. If the drill with a fully charged battery still won't penetrate, grab a corded drill and see if you're able to drill a small pilot hole. If you're able to drill a pilot hole with the corded drill, the power of your cordless drill was probably the problem.
Why do drills stop working?
IF DRILL STALLS, it is usually because it is being overloaded or improperly used . RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT DEPRESS TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL — THIS CAN DAMAGE THE DRILL.
How do you fix a overheated drill?
3:075:02Why is My Cordless Drill Overheating? - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we look inside and there is a missing spring or spring in this situation is more than likelyMoreSo we look inside and there is a missing spring or spring in this situation is more than likely what's been causing the overheating the simplest solution on this one is to place our brushes. Here.
What is the common cause of breakdown of electric drill?
Possible Reasons for a Defective Power Drill Claim Unsafe design/design defects. Lack of proper safety guards. Improper warning provided. Manufacturing flaws.
Why has my Dewalt drill stopped working?
Faulty Battery First, check to see if the battery needs charging. If it is fully charged, but does not hold the charge for long while using the drill , you may need to purchase a replacement battery.
Why did my Milwaukee drill stop working?
The battery has been charged and the drill still has no power. If the battery has been charged there is a chance that the battery could be faulty. Try another battery that has been charged before doing anything else. If you try another battery and still have no power you could have a faulty circuit board.
Who repairs Makita tools?
Makita Factory Service Center Technicians will repair your tool with genuine Makita parts
Does Makita charge for repair?
For repairs not covered under warranty, the customer may request an estimate prior to repair. If authorized by the customer, the repairs will proceed and upon completion the customer will be informed of the actual costs. Prior to releasing the tool for free return-shipping, Makita will collect full payment for cost of repair.
What is the gear assembly on a cordless drill?
The gear assembly is a critical component of your cordless drill. It consists of the transmission, the clutch, and the hammer-drill mechanism.
How to loosen Allen wrench chuck?
While securely holding the drill against the work surface, strike the exposed end of the Allen wrench with a hammer. This will (eventually) loosen the chuck assembly. (It may require several attempts).
Where to install new gear assembly?
Install the new gear assembly into the lower half of the housing.
What to do if you have no reverse on cordless drill?
if there is no reverse on your cordless drill, check either the lever or the switch. Once you have determined the part that needs to be fixed you can now use our expert guide to repair it yourself. Check your owner's manual for specific advice regarding your model.
What to do if your cordless drill is hot?
If the motor gets hot in your cordless drill, check the following parts: carbon brush, armature, holder, and bearing. Once you have determined the part that is causing the issue, read our repair tips to help complete the repair yourself. You might be surprised how easy it is to fix. Check your owners manual for detailed instructions for your model.
What to do if cordless drill has no variable speed?
If your cordless drill has no variable speed, check the switch or the carbon brush. Save on time and money and use our repair guides to fix your tool yourself. Always refer to your owner's manual for more complete instructions regarding your specific model.
What kind of battery does a cordless drill use?
There are higher voltages however, with some that will produce as much torque as a corded drill. The most common batteries used are lithium ion and nickel-cadmium, with the market split about 50/50.
What controls how fast a drill spins?
The clutch controls how fast the drill spins. This guide will show how to remove the clutch.
