How To Repair A Nail Gun
- Check the power cord for wear and tear. One way to avoid dangerous nail gun accidents is to check the power cord for wear and tear. ...
- Clean the gun of any debris or nails that may have gotten inside while it was being used. ...
- Repair Parts. ...
Full Answer
Why is my nail gun not working?
Well, some of the culprits may be:
- Dirt- clean the tool.
- Insufficient lubrication- add lubricant.
- Wrong fasteners- Replace the nails.
- Incorrect pressure settings- adjust accordingly.
- Nail jam- check and clear.
- Something is wrongly setup- inspect the tool and correct as necessary (diassemble if needed)
Why is my nail gun not firing?
Repair Maintenance Issues:
- Loader spring is weakened and either twisted, torn, or frizzed,
- the magazine is twisted,
- the guide channel narrowing has occurred,
- nail gun firing pin won’t retract,
- nail gun leaks air around the trigger,
- the guide is broken or buildup dirt or grease around it,
- nail gun leaks air around trigger,
- Hose fitting or nosepiece problem, etc.
How do I Fix my Nail Gun that is misfiring?
Things You Will Need
- Air line lubricant tube
- Hex tool
- Needle-nose pliers
How to remove a jammed nail from my Nail Gun?
How to Repair a Bostitch Nail Gun
- One problem you might experience with the Bostitch nail gun is that it frequently double or triple shoots nails.
- If air is leaking or blowing out through the trigger, it could be because the O-ring in the trigger (sometimes referred to as the purple ring) is out ...
- Sometimes the piston on your Bostitch nail gun may become stuck after firing. ...
How do you fix a nail gun that won't fire?
My Nailer Won't Fire – Troubleshooting Common Causes of Jams and MisfiresClear Jams. ... Inspect Your Air Supply. ... Reload the Magazine. ... Clean the Tool. ... Replace Seals and O-Rings. ... Inspect for Damage. ... Take It to the Service Center.
How do you fix a nailer?
4:206:10How to Fix a Nail Gun! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell I had the system cranked down to 60 psi I've run wrapped it up to 110 let's see how that works.MoreWell I had the system cranked down to 60 psi I've run wrapped it up to 110 let's see how that works. Well it worked but no nail came out.
Can nail guns be rebuilt?
You can do the entire job yourself in about two hours and save money in the process. I'll show you how to rebuild a Bostitch framing nailer with a master O-ring kit and a trigger valve assembly. If you have a different brand, don't worry. The rebuild is similar for others.
Why is my nail gun misfiring?
The nail gun will misfire if the piston is not regularly lubricated. Unscrew the air line connector from the bottom of the nail gun with your fingers. Remove the air line hose from the nail gun. Turn the nail gun over and drip 10 drops of air tool lubricant into the air line hose hole.
Why is my nail gun leaking air out back?
On a properly working pneumatic tool, when air is forced into the firing valve, this pushes the valve upward, which opens the main cylinder sleeve and allows the air to drive a fastener. If the "O-Ring" fails to seal, the air will escape, creating your leak.
How do you replace an O ring on an air nailer?
1:103:52Bostitch Nail Gun Repair - How to Replace the O-Ring - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the bumper comes out of the gun you just place it right back inside with the driver unit removed.MoreIf the bumper comes out of the gun you just place it right back inside with the driver unit removed. Now I can install the new o-ring I'll remove the old o-ring from the piston.
How does a pneumatic nail gun work?
Commonly used nail guns use pneumatic power—compressed gas—to create pressure to drive the hammer onto the nail, and the nail into the surface. When the user pulls the trigger, the pressurized gas in the barrel drives the hammer down. The tool connects to an air compressor with a hose.
How do you fix a Porter Cable nail gun?
0:059:11Porter Cable Nailer Repair - How to Replace the Overhaul Maintenance ...YouTubeStart of suggested clipEnd of suggested clipThe overhaul maintenance kit consists of a new trigger valve as well as all of the o-rings seals andMoreThe overhaul maintenance kit consists of a new trigger valve as well as all of the o-rings seals and bumpers that you will need to rebuild your nail gun the kit solves common nail gun problems such as
How do you disassemble a Bostitch nail gun?
3:5911:00BOSTITCH 2 in1 finish nail gun jam fix! MODEL- SB-1850BN - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you lift it's light enough marked slightly but enough for the nail just to fall out you willMoreOnce you lift it's light enough marked slightly but enough for the nail just to fall out you will just shake it out and it should come out if it doesn't come out for whatever.
What can go wrong with a nail gun?
Troubleshoot Guide for Common Nailer Problems#1 Air leaks somewhere on your nailer. Many air leaks are caused by faulty or damaged seals and o-rings. ... #2 Nailer does not drive fasteners correctly. ... #3 Nailer feels “sluggish” ... #4 Driving blade does not retract or retracts slowly.
How do you lubricate a nail gun?
1:011:45How to Oil a Framing Nailer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere would be winter gun oil and normal gun oil just different viscosities to allow the gun to workMoreThere would be winter gun oil and normal gun oil just different viscosities to allow the gun to work best at different temperatures.
Will a nail gun fire without nails?
Insure that the nails are compatible with the gun. If they're not, the gun may not fire, misfire, or self destruct. If it is making a "big" dent then it usually means that your nails are jammed.
How do you unjam a framing nailer?
How to unjam a nail gun:Unscrew the two front nose bolts, or lift the nose latch, releasing the front nose plate.Open the nose.Clear the jam and push the driver blade back to its rest position.Close the front nose and refix it.Ensure the work contact element is free.Reinsert the battery and the fuel cell.More items...
How do I fix my air stapler?
1:3014:45Fix a Air Stapler Gun - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull it up take it out with one side just don't lose it then this comes out it's just hooked in theMorePull it up take it out with one side just don't lose it then this comes out it's just hooked in the body there kid do some of it.
How does a pneumatic nail gun work?
Commonly used nail guns use pneumatic power—compressed gas—to create pressure to drive the hammer onto the nail, and the nail into the surface. When the user pulls the trigger, the pressurized gas in the barrel drives the hammer down. The tool connects to an air compressor with a hose.
How do you unjam a Dewalt nail gun?
0:271:29How To UnJam a Dewalt Framing Nailgun - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust pull those out they don't come off completely start right about losing them. And then take theMoreJust pull those out they don't come off completely start right about losing them. And then take the magazine out. And get into the actual barrel of your gun.
How to repair a nail gun?
The procedures to repair a nail gun are straightforward and will help you keep it operating at peak effectiveness. The nail gun will misfire if the piston is not regularly lubricated. Unscrew the air line connector from the bottom of the nail gun with your fingers. Remove the air line hose from the nail gun. Turn the nail gun over and drip 10 drops ...
How to keep nails from sticking in nail gun?
To keep nails from sticking inside the magazine, first unscrew the air line connector from the bottom of the nail gun and remove the air line hose. Press down on the locking latch by the side of the trigger. Lower the magazine from inside the nail gun. Empty any nails in the magazine into your palm.
How to get a stuck nail out of a magazine?
Empty any nails in the magazine into your palm. Pull out any nails in the open compartment directly above the magazine — you may need a set of needle-nose pliers to pull out a stuck nail by the head. Apply air tool lubricant on the clean edge of a soft cloth.
What is a nail gun?
A nail gun uses a burst of compressed air to fire a nail into a material that would otherwise require manual hammering . There are a number of problems that a nail gun can encounter during normal use, all of which may result in improper operation and a loss of efficiency.
How to remove air line hose from nail gun?
Remove the air line hose from the nail gun. Turn the nail gun over and drip 10 drops of air tool lubricant into the air line hose hole. Place the air line hose back on the hole and screw the air line connector clockwise. Screw the valve on the air compressor three turns clockwise. Aim the barrel of the nail gun off in the distance.
What happens if your nail gun drops?
If your nail gun dropped somehow, the firing pin might get bent. Besides, if you use incompatible fasteners for your nail gun, it may also bend the pin. To get rid of this problem, check out whether any damage took place or not during the drop. If any damage occurred, replace the damaged part. Make sure you use compatible fasteners to avoid such problems in the first place.
Why is my Paslode nail gun misfiring?
Misfiring is the most common problem of the Paslode nail gun that we most commonly experience. There is no one cause in particular of this problem .
What is the problem with Paslode nail gun?
The next most common problem of the Paslode nail gun is broken, damaged, or worn O-Ring. The O-Ring is generally located near the head valve. It seals the air from leaking. When the O-Ring gets damaged or worn somehow, it causes air leaking. If you are affirmative about this being the issue, removing the O-Ring will most likely solve things.
How to remove battery from a spherical gun?
Remove the battery from the bottom of the gun by pressing the release button. After that, empty the nail clip by pulling the nail feed down. Release the flip catch on the gas canister restraint on the rear of the gun and remove the gas canister.
Why is my nail gun light flashing red?
Sometimes the light on the handle of the nail gun is flashing red and green. It indicates that there may have been some problem with the nailer. An unstable motor is the main reason for flashing the red and green light on the handle. This alert points that you have to either repair or replace the motor.
Do nail guns need to be cleaned?
If you use your nail gun on a daily basis, it needs to be cleaned regularly. Otherwise, small dirt from the job site pollutes the magazine that causes misfiring.
Is it hard to repair a Paslode nail gun?
It turns out that repairing your Paslode nail gun is not much of a difficult task. Knowing how to keep your patience is more important than knowing how to mend it. If you are an amateur, it is forgivable to mess things up.
How to fix a nail gun that is not working?
There may be some issues which you can easily correct. Try these two solutions to fix the issue; Raise the Air Pressure. Lubricate or Replace the O-rings.
Why does my nail gun leak air?
Usually this happens due to the wear and tear associated with pulling the trigger so many times. You will need to get a new trigger valve in that case. You will need to follow instructions for the brand of nail gun you are using, purchase a new trigger valve, and replace it.
What to do if your nailer is not moving?
If there is no noise or movement when you depress the trigger, be sure that it is plugged in and active. Take off the cap located on the head of the nailer, use a wooden dowel and push the driver to the bottom. If it does not move, you either have a stuck nail, a broken driver, or the trigger valve itself is broken.
What are O rings on a nail gun?
O-rings are generally made of rubber or a synthetic rubber designed to seal the area around the head valve to prevent the air from getting through while allowing the cylinder to operate normally. This is a relatively easy fix as you simply order new O-rings for the nail gun or perhaps a rebuild kit. A rebuild kit should match the model of the nail ...
What does it mean when a nailer does not countersink?
Other issues deal with the fastener that does not countersink. This may mean that the driver tip is broken or compromised. You can test this out by removing all the nails from the magazine, taking the cap off the head of the nailer, and using a wooden dowel to push the driver down to the bottom. If the driver does not extend past the end of the nailer, then you will need to order a new driver.
Can a nail gun be repaired?
While some problems with nailers, may require professional nail gun repair service or replacement parts, there are other issues that you may be able to solve on the job site. What follows are some of the more typical problems encountered with nail guns and what to do about them.
Do nail guns blow air?
Nail Gun just Blows Air and Not Shooting Nails. A nail gun is quite handy, speeding up the job of fastening materials together far greater than using the old-fashioned hammer. However, nail guns are subject to breaking down just like any other mechanical device. This means when something goes wrong, it pays to know what to do so you can identify ...
Why are my nail guns not working?
Air leaks on the nail gun can cause any types of damages, faulty, or O-rings. If u noticed that your nail guns aren’t working properly, then make sure to check if any of the O-rings or seals of your nail guns are damaged or not.
What is a nail gun?
Nails guns are an essential tool for woodworkers or carpenters that are manufactured to drive nails into the wood or any type of material. The power tools are using for a very long time that makes your woodworking job much easier and faster.
Why is my nail gun dirty?
Another common problem with the nail gun is the driving blade that doesn’t retract properly. If you aren’t lubricant your nail gun regularly, then the driving blade can become dirty. For that reason, they can cause poor performance.
Why is my nail gun misfiring?
Misfiring is one of the most common problems you can face while firing the nails with the nail gun. There can be various causes for the problem is happening. One of the main reasons for the problem could be the nail jam.
How does a combustion nail gun work?
Combustion nail guns are using the fuel canister and the battery. The battery helps to charge the spark plug of the nail gun. Then it can burn a few amounts of combustible gas that is released from the fuel canister. After that, it fires the piston downwards that can drive the nails into the surface.
What is a pneumatic nail gun?
Pneumatic nail guns are a really powerful option to drive nails into any surface. They can use pressured air that cat produces the compressing force efficiently. Whenever the trigger is pulled, it can move the piston. Then it drives to fire the nail.
Why does my nail gun make a noise?
There can be several reasons for the strange noise problems. If the motor of the nail has any issues that can cause the noise. Besides, the fan of the nail gun could be hitting against something that can create the sound as well. If you don’t clean them regularly, that can also create that problem. Therefore, make sure to check on them properly if you hear any strange noise while working. So that you can fix them immediately. Also, keep them clean all the time so that no obstacles can cause any problems.
