how to repair a paved driveway

^{Steps for Asphalt and Concrete Driveway Repair}

• If weeds are growing out of the cracks, pull them.
• Clean the cracks, using a strong spray from a garden hose.
• Apply weed killer.
• When the crack is deep, fill it to within 1/4 inch of the surface with sand.
• Tamp down the sand.
• Apply patching compound ( for asphalt driveway repair) or concrete.
• Allow it to cure.
• Apply sealant.

How much does it cost to repair a driveway?

• All-weather blacktop patch: about $14 for 60 lbs.
• Permanent pothole repair (55-lb.): $43
• Premium cold asphalt (50-lb.): $17
• Permanent pavement repair patch (60-lb.): $33
• High-performance permanent pavement repair (50-lb.): $12

When to repair or replace your driveway?

Your concrete driveway may be damaged if:

• There are cracks, splits, or breaks
• Your driveway isn’t clearing water or draining properly
• The seal or finish is corroded or worn away
• The base/foundation is unstable
• It is “too old” or beyond its lifespan

How often should I replace a driveway?

How Often Should I Reseal My Driveway? You should reseal your driveway every three to five years, depending on the climate you're in. In a cold, wet climate you may need to reseal more often, whereas in warmer climates like California your asphalt sealcoating will last longer.

Should I resurface, repair, or replace my concrete driveway?

When it comes to fixing a driveway, your two options are generally either resurfacing it or replacing it entirely. However, there is a third option: patching it with a little extra concrete where necessary. If there’s only one hole or a surface-level crack, patching the concrete could be your best bet.

How do you fix crumbling asphalt driveway?

Use asphalt paste patch that contains fine aggregate to fill small holes and gaps along curbing. Mound the repair above the surface the way crews do on roads. They let car tires reduce the speed bumps and gradually compact the mix. You can use a heavy metal tamper, or the end of a 2-by-4 to pound the patch nearly flat.

How do you fix dips in a paved driveway?

Open the asphalt repair mix and shovel a 2-inch layer inside the sunken area. Tamp it down with the end of a piece of scrap 4-by-4-inch lumber. Continue adding 2-inch layers and tamping them until you get to the top of the sunken asphalt, instructs Family Handyman. Mound the final layer so it is higher in the middle.

How do I fix patches on my driveway?

1:042:03HouseSmarts Fix it in 15 "Patching Asphalt Driveways" Episode 206YouTubeStart of suggested clipEnd of suggested clipAnd if you see low spots it's okay you can add a little more of the patching material a little bitMoreAnd if you see low spots it's okay you can add a little more of the patching material a little bit of water tamp. It all down and go now the manufacturer.

How do you patch and seal an asphalt driveway?

Step 1: Clean Driveway. Use a leaf blower or broom to sweep leaves, acorns and dust from the surface of the driveway. ... Step 2: Patch Cracks and Holes. ... Step 3: Clean Driveway and Mix the Sealant. ... Step 4: Seal Edge by Hand. ... Step 5: Pour Sealant Along Edge. ... Step 6: Apply a Second Coat.

How do you fix driveway depression?

0:371:35How To Repair Driveway Depressions - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen using pothole filler use your trowel to apply material into the crack enough to form a smallMoreWhen using pothole filler use your trowel to apply material into the crack enough to form a small mound slightly above the level of the surrounding.

Why is there a dip in my driveway?

Water leaks: Water is an enemy of driveways, which is why it's important to watch out for surface cracks, leaking pipes or garage downspouts. These weaknesses may cause water to pool on and under the surface, causing the soil or sub base to weaken and sink.

Will new asphalt stick to old asphalt?

If you put a new layer of asphalt over the existing driveway it will get the same rut very quickly. Asphalt is highly flexible and once the ground under asphalt sags asphalt sags too. The real solution would be to tear the driveway up and put proper ballast.

How do you fix a large hole in asphalt driveway?

3:385:30How to Repair an Asphalt Pothole | Ask This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow what we're going to use for our top coat is this cold packs asphalt repair if you take a look atMoreNow what we're going to use for our top coat is this cold packs asphalt repair if you take a look at it it's a stone mixed with asphalt binder. We just pour it in the hole in inch and a half thick.

Is it OK to pave over an existing driveway?

An overlay or resurface can be used on an asphalt driveway, parking lot, or road way. It consists of installing a new layer of asphalt over the existing asphalt and grinding at the transitions (i.e. sidewalks, garages, drains, curbs, or other asphalt points).

How do you patch a concrete driveway?

1:305:16How To Repair Concrete | Pro Tips For Repairing Concrete - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr you can use a vinyl concrete patching agent and a putty knife to fill it in for a wider crack youMoreOr you can use a vinyl concrete patching agent and a putty knife to fill it in for a wider crack you will need to use a small sledgehammer.How To Repair Concrete | Pro Tips For Repairing Concrete - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you patch a concrete driveway?

What is the cheapest way to resurface a drive?

Of the four paving materials described in this guide, aggregate (gravel) is the least expensive, followed by asphalt, concrete, and paving stones. If you're installing your driveway on a shoestring budget, gravel is your best choice. If you have more wiggle room, you'll have more choice.Types of Driveways for Your Home - Materials & Costs - Money Crashershttps://www.moneycrashers.com › types-driveways-ideas-...https://www.moneycrashers.com › types-driveways-ideas-...Search for: What is the cheapest way to resurface a drive?

How do you repair a concrete driveway surface?

0:394:28How to Resurface Concrete - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore resurfacing your slab deeply spalled areas and large cracks should be repaired using concreteMoreBefore resurfacing your slab deeply spalled areas and large cracks should be repaired using concrete resurfacer that has been mixed to a triable consistency.How to Resurface Concrete - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you repair a concrete driveway surface?

How do I repair my concrete driveway?

How to Resurface a Concrete DrivewayRemove debris. If a crack is less than a quarter-inch, it's a prime candidate for simple resurfacing. ... Wash the driveway. Wet down the driveway with a pressure washer. ... Mix concrete and water. ... Fill the cracks. ... Let dry. ... Resurface. ... Prevent slips. ... Watch the video above to learn more!How to Repair and Resurface a Cracked Concrete Drivewayhttps://todayshomeowner.com › video › how-to-caulk-an...https://todayshomeowner.com › video › how-to-caulk-an...Search for: How do I repair my concrete driveway?

How do I repair a brick paver?

Start by preparing a small test batch. Mix the mortar according to its packaged instructions. Scoop out a small portion of this mix with a trowel. Let the mortar mix dry for a few minutes. Now, check the mix for color consistency and overall thickness. The color should be somewhat similar to the mortar lining of the existing brick paver. The consistency shouldn’t be too thick or thin, i.e. it should be workable without having an easy flow.

How do I replace a paver brick?

If you are replacing the paver brick, proceed by wetting one side of the brick. Spread some mortar on the wet side of the brick and spread it evenly using the trowel. Place this brick within the mortar-layered surface. If you are repairing the paver brick, use the cracked side as the interior side, i.e. wet it and layer it with mortar. Place it in the same manner.

Can you use brick on a cracked driveway?

If the brick has slight cracking on the exposed side, you can still use it. This is done by turning the cracked side inwards, i.e. towards the inner mortar lining and patching the new, external surface. If you plan to replace the brick, get a suitable replacement. Matching the color of the replacement brick and the driveway paver surface is crucial. This ensures the replaced brick isn't obvious.

Do driveway brick pavers need repair?

Among household landscaping elements, driveway brick pavers are among the most common of surfaces. Driveway brick pavers often need a basic repair. This is because they are subjected to daily wear and tear besides issues like oil leaks, pressure of water hoses and neglectful handling. A homeowner can easily execute basic driveway brick paver ...

How much does a concrete driveway cost?

Running approximately $4 to $5 per square foot for professional installation, concrete is one of the strongest construction materials around, and it forms a solid, ...

How does a gravel driveway work?

Gravel driveways are constructed with a slight crown, a high spot going down the center that allows water to run off to both sides. Repetitive tire tracks in the same place can create low spots that hold water and eventually cause the formation of ruts. An excavator can re-grade the road with a large blade that pulls gravel back to the center of the road to recreate the original crown shape.

What is the best way to fix cracks in concrete?

For just one or two small cracks less than half an inch, consider fixing with a concrete crack filler, such as Quikrete Advanced Polymer Concrete Crack Sealant (available from The Home Depot ), dispensed with a standard caulking gun.

Why do you need an excavator for a gravel driveway?

Call an excavator if portions of the gravel driveway are washed out by heavy rains and water runoff. This is a common problem for country dwellers whose land often isn’t designed to drain away from their driveway. When heavy rains come, the runoff can be concentrated in small areas, cutting through farmland and over gravel drives, washing the gravel away and creating ruts. An excavator will haul in additional gravel to fill the ruts and then grade and compact that portion of the driveway.

Why do people put gravel on their driveways?

Usually found in small rural communities or leading to country homes, gravel driveways are often installed to promote drainage, when asphalt or concrete contractors aren’ t available, or where the long length of a driveway makes it cost-prohibitive to install asphalt or concrete.

What is the best way to fix spider webs in asphalt?

Numerous tiny spider web cracks in asphalt can be remedied with a mop-on asphalt sealer, such as Henry Driveway Filler and Sealer (available from Walmart ). This product contains an asphalt resin that can be applied without heat.

What to use to repair spalling on concrete?

If your concrete driveway is spalling (flaking off in patches), consider resurfacing with a product such as Quikrete Concrete Resurfacer (available from Lowe’s ). It comes dry in a 40-pound bag and must be mixed with water and applied according to package instructions. Once mixed, it’s spread over a spalled section of the driveway with a squeegee to fill in the damaged spots and form a new smooth surface.

How do I patch a crack in my driveway?

Then do your patching when temperatures are at least 60°F so the repair material will cure. Fill 1/2-in. cracks with sand to within 1/4 in. of the surface, then add an asphalt filler, such as Quikrete's Blacktop Repair ($2 a quart) or UGL's Driveway Crack Filler ($3 a tube). An alternative is Dalton's Pli-Stix, a rope-like crack and joint sealer you melt in place with a torch.

What to do if your driveway is crumbling?

If your driveway is crumbling or has heaved or subsided in a major way, then your best option is to replace it. The same applies if it's allowing water to seep into the subsoil around your home. But often the problem is just cracks, which let in water that erodes the driveway base and allows freezing temperatures to do further damage.

How much does it cost to build a driveway?

Prices range from $1 per square foot for stone and gravel to $13 or more for cobblestone paving.

How much does Dalton's Super Patch cost?

For deeper holes, pour in gravel to within 4 in. of the surface, then trowel in Dalton's Super Patch ($7 per gallon). Or, shovel in cold-patch asphalt in 1-in. layers, packing each firmly as you go with the end of a 4X4 or the head of the sledgehammer.

How do I fix a crack in a concrete slab?

To fix large holes and deep cracks, fill them with gravel to within 4 in. of the surface , pour in concrete, tamp with a magnesium float and finish with a flat trowel or broom to match the existing finish. However, the larger the patch, the shorter its longevity—winter freeze/thaw cycles that exert pressure of 30,000 psi can make short work of big repairs.

What is the difference between pavers and cobblestone?

Cobblestone, or Belgian block, is more traditional and comes only in a rectangular shape .

How deep should a gravel base be?

A new gravel base should be 3/4-minus gravel and 8 to 10 in. deep. After the concrete is poured, to prevent cracking, use a sprinkler to keep concrete moist as it cures.

What to do with a driveway that keeps you up?

If what to do with your driveway is keeping you up nights, don’t waste any more time worrying. One call to Concrete Craft will have the experts who know concrete at your service! They can evaluate your driveway and talk you through the best options for your desired result, whether to repair, restore, or create a fabulous faux stone design with a decorative concrete overlay in stained, stamped or hand-carved concrete.

How long does it take for a concrete driveway to cure?

No waiting up to 30 days for a new concrete driveway to cure and harden. A beautiful, new driveway for far less cost than demolition and replacement. Concrete Craft can have your ugly driveway repaired, restored, or resurfaced in a matter of days so you can get on with the more important things in life. And, we won’t damage your yard ...

What is decorative concrete overlay?

If your driveway needs a whole new look, a decorative concrete overlay will create a new finish that covers minor surface damage like cracks, imperfections and discoloration. The overlay creates a durable finish and long-lasting bond with the original concrete that will not chip, crack or peel. Concrete overlays can be stained, stamped, and hand-carved in faux finishes like flagstone, cobblestone, Ashlar slate, and Roman slate for the exquisite look of real stone.

What is concrete overlay?

Concrete overlays can be stained, stamped, and hand-carved in faux finishes like flagstone, cobblestone, Ashlar slate, and Roman slate for the exquisite look of real stone. Real stone molds and hand-applied stain colors result in finishes that look natural and authentic.

How to contact Concrete Craft?

As a local business owner in your community, we care about your complete satisfaction. Call 866-813-3699 today or go online to www.concretecraft.com to find the Concrete Craft location nearest you and request a FREE consultation. You can trust Concrete Craft to deliver on the promise of the driveway of your dreams.

What is Durable Surface?

Durable surface resists abrasion and impact and withstands any kind of weather without cracking or peeling.

What is stained concrete?

Stained concrete transforms with vibrant color, including one-color or multiple colors, and borders or stenciled designs.

When is the best time to repair a driveway?

So the best time to do the project is during an extended warm, dry spell. You can do it in spring or fall, but cold weather and rain will greatly extend the cure time. This driveway repair is a messy job, and no matter how careful you are, you’re going to get tar on your clothes and shoes. You can’t wash off the tar with soap and water.

How much does it cost to dig out an asphalt driveway?

If you don’t, water will pool in the depression, seep into the soil below, and eventually destroy the driveway. Asphalt companies charge about $1,000 to dig out the old portion and install a new apron. Concrete contractors charge even more. But you can rebuild your asphalt driveway apron yourself.

How to build a cold patch?

Pour in a small amount of cold patch material and level it with a square-blade shovel. Tamp down a test section and measure the depth. The bottom layer should only be 1/2 in. thick when compacted. Add or remove cold patch material and then tamp down the entire starter row. Photo 3: Build additional layers.

How does cold patch work?

Cold patch works only when it’s compacted and “keyed” into at least two vertical surfaces. So don’t think you can build up the driveway height by pouring cold patch on top of the old sunken asphalt—the patching material will just break off in chunks. Instead, you’ll have to cut out the sunken asphalt (Photo 1).

Can you wash tar off a driveway?

You can’t wash off the tar with soap and water. So wear old clothes and shoes that you can toss into the trash when you’re done. If you have to go into the house during the project, leave your shoes outside so you don’t track tar into the house. Here’s how to make the DIY driveway repair.

Can you fix a sinking driveway apron?

But when your driveway repair has sunk to the point where it’s 4 or 5 in. lower than your garage floor, it’s time to fix it. If you don’t, water will pool in the depression, seep into the soil below, and eventually destroy the driveway.

How long does a driveway last?

Professionally installed paved driveways will last between eight and ten years on average. General wear and tear will affect the finish of the asphalt and the makeup of the product itself is made to deteriorate in that time span.

What happens if you don't dig a hole in asphalt?

Often issues arise after the first major rainfall. As the asphalt is exposed to the flow of water any weaknesses in the base will be evident.

How long does it take for asphalt to oxidize?

It may show up early if your driveway has direct exposure to the midday sun. But most often this stage is seen anywhere from 9 to 18 months after the asphalt is poured. Loose gravel and cracking that appears within the first year is definitely a problem.

How long does it take for a driveway to show age?

Retaining the dark color and presenting a nearly seamless appearance, the driveway will not begin to show its age until about twelve months after installation. By that point oxidation will begin and the surface will look grey and faded.

When does sand start to work out of driveway?

Sand will begin to work out of the driveway during the third year, eventually resulting in loose gravel between years four and five. By the sixth and seventh year you are likely to see cracking and during the eighth year and beyond potholes will begin to appear.

Can you take up asphalt and start again?

Whether you have hired a contractor that performed a lousy job or got in over your head on a DIY project, problems with your paved driveway can be solved. Many times it may be best to take up the existing asphalt and start again.

Can you patch a hole in asphalt?

Patching holes is one possible method of repair, but that is only a surface remedy. The next rainfall or freeze and thaw will cause more damage to the driveway and your patch will be for naught. There are plenty of products on the market that claim to seal asphalt cracks effectively.

Why does my driveway fall off?

A common problem with asphalt driveways is that they break loose at the edges and crumble. Homeowners’ bad habits such as driving off the side of the driveway can advance the deterioration of your edges , causing them to fall away in places.

How long does it take to drive on asphalt?

Asphalt is affordable for starters, and after installation, you can typically drive on it within 72 hours. This durable driveway option can stand up to weather and both vehicle and foot traffic. But asphalt is not entirely immune to wear.

What is a 45 degree grading on a driveway?

Edging refers to the method of securing the sides of your driveway to prevent cracking, crumbling, and other damage. Take a look at most asphalt driveways, and you’ll notice that they have edges with a 45-degree grading. Your driveway must have this to help transfer stress from the asphalt to the solid ground beneath it.

Where is Lyons and Hohl Paving?

For reliable, trusted, and honest paving in the Lancaster and Reading, PA area, look no further than Lyons & Hohl Paving. We’re here to help, and that includes high-quality asphalt paving, asphalt repair, and asphalt maintenance to residential and commercial clients.

Can you add asphalt to a damaged driveway?

If the driveway’s edge is severely damaged and a part of it is missing, adding new asphalt to repair it is in order. This process may require you to chip away at the damaged area’s edge so that you create a straight line. You also might need to add gravel, like you would a pothole, and compact it in the same manner.

Can you fill a hole in asphalt?

Lastly, you’ll fill in the hole with cold asphalt and make the surface level. But, keep in mind, cold asphalt sometimes doesn’t bind as well as hot asphalt. If you’re dealing with a more extensive damaged section, you’ll want to contact a contractor to professionally repair your driveway.

Can you repair cracks in asphalt?

After you have your new border in place, you can repair the cracks and crumbles to restore the asphalt surface. If damage to your driveway is in a small, confined area, you might be able to make the repairs yourself with asphalt patching material or filler. You’ll first want to clean the area and remove any weeds.