Peerless Faucet Repair Instructions
- Step 1. Turn the water valve under the sink to the closed position.
- Step 2. Take off the handle to the Peerless faucet by removing the screw at the bottom of the handle with an Allen...
- Step 3. Use pliers or the tip of a screwdriver to push the plastic washer under the handle (now on top of the faucet...
Full Answer
How to fix a leaky Peerless kitchen faucet?
Peerless Cartridge Faucet Repair. Turn off the water. Remove the handle. Unscrew the retaining nut, using locking pliers. Grasp the valve stem with pliers and lift out the cartridge. Check inside the valve housing for rubber gaskets in the inlet holes and lift out any you find using a screwdriver. Click to see full answer.
How to replace a kitchen faucet with two handles?
- Switch off the water supply valve
- A decorative cap hides the bolt that holds the handle to the faucet. ...
- Unscrew the bolt using a screwdriver.
- Take off the nob so that you can reach the valve stem.
- Where you have taken the knob off, replace it with a new one. ...
- Insert the large screw into the knob and start screwing it using a screwdriver.
Where to buy Peerless faucet parts?
You can pick up the phone and call our Customer Service representatives at 1-800-438-6673. As soon as representative answers, he or she should be able to help you obtain the missing parts. Many Peerless distributors will provide parts for a new faucet. You should check with your distributor first to determine their policy.
How to repair a leaky single handle cartridge faucet?
- Turn off the shut off valves and open the faucet to drain the water.
- Plug off the sink drain opening.
- Remove the handle. ...
- Remove the retaining ring. ...
- Grab the cartilage with a wrench or pliers and pull it straight out. ...
- Soak up the water inside the valve using a cloth.
- Apply some grease on the new cartilage’s O-rings
- Install the new cartilage. ...
How do you remove a Peerless single handle faucet?
Look for the nylon locknuts holding the body of the faucet to the countertop or sink. The locknuts twist onto two threaded shanks connected to the underside of the Peerless faucet body. Rotate the locknuts counterclockwise to remove them from the shanks and release the faucet.
How do you stop a peerless faucet from dripping?
What do I do if my single-handle kitchen or lavatory faucet drips from the aerator?Remove the aerator (it should twist off by hand).Turn off the water supplies.Turn the faucet handle to the "on" position.Turn the water on at the supply.Flush the faucet and supply lines for one minute.More items...
How do you disassemble a Peerless kitchen faucet?
0:303:11How to Repair a Leaky Single Handle Ball Kitchen Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst you will need to turn off the hot and cold water supply valve under the sink. Next. You willMoreFirst you will need to turn off the hot and cold water supply valve under the sink. Next. You will need to remove the single lever handle. This may require using an allen wrench to loosen the hammer.
How do I know what model my Peerless Faucet is?
Your faucet's model number may be found on the packaging, and also on the Installation instructions provided with your faucet.
How do you remove a peerless faucet stem?
1:025:31Delta/Peerless Faucet Cartridge Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn it off by turning these a quarter of a turn. We turn off both sides. Because water can flowMoreTurn it off by turning these a quarter of a turn. We turn off both sides. Because water can flow from one side of the other when you take this assembly apart.
How do you fix a leaky single handle faucet?
0:182:44Repairing a Leaky Single Handle Ball-Type Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst you will need to turn off the hot and cold water supply valve under the sink next. You willMoreFirst you will need to turn off the hot and cold water supply valve under the sink next. You will need to remove the single lever handle. This may require using an Allen wrench to loosen the handle.
How do you change the O ring on a Peerless kitchen faucet?
0:231:34Leaky Faucet Base – O-Ring Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd u o-rings onto the faucet body within their group slots making sure the o-rings are not twisted.MoreAnd u o-rings onto the faucet body within their group slots making sure the o-rings are not twisted. Apply silicone grease to the o-rings. Once mounted on the spout base reinstall. The spout handle.
How do you change a peerless faucet?
0:595:01How to Install a Peerless Single Handle Pulldown Kitchen FaucetYouTubeStart of suggested clipEnd of suggested clipInstall the lock nuts onto the studs and tighten securely by hand insert your peerless faucetMoreInstall the lock nuts onto the studs and tighten securely by hand insert your peerless faucet through the escutcheon in the mounting hole. And secure the valve with the gasket washer.
How do you tighten a peerless faucet?
Use pliers or the tip of a screwdriver to push the plastic washer under the handle (now on top of the faucet head) left to loosen it. Then push it back right to tighten it, reassemble the faucet and test it.
Does Peerless have a lifetime warranty?
You're probably wondering about the "limited" part of that warranty, aren't you? Our Lifetime Limited Warranty applies to Peerless faucets manufactured after January 1, 1995. And it's one of the most extensive in the industry (provided you are the original purchaser).
Are Delta and Peerless the same?
Peerless Faucet Company is owned by Masco Corporation, as is Delta. So, they both operate under the same parent company. That said, Peerless is considered part of Delta's lineup. Delta has a few different product lines: Peerless, Delta, and Brizo.
Where do I find my faucet model number?
Identifying Your Faucet ModelThe model number is printed on a tag that is attached to the cold water supply line of the faucet.The supply line is located below the sink, countertop, bath rim, or behind the bowl of a bidet.The model number, or part number, is typically preceded by "P/N."More items...
How do I stop my kitchen faucet from dripping?
1:123:00How to Fix A Dripping or Leaky Single Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipAdd a little plumbers grease and replace the spout put new seats on new spring. And put them back inMoreAdd a little plumbers grease and replace the spout put new seats on new spring. And put them back in place replace.
How do you fix a dripping kitchen faucet with two handles?
0:424:49How to Repair a Leaky Two-Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you determine the trouble stem you'll need to turn off the water. Next remove the handle with aMoreOnce you determine the trouble stem you'll need to turn off the water. Next remove the handle with a Philips head screwdriver. So that the stem is visible.
How do you tighten a peerless faucet?
Use pliers or the tip of a screwdriver to push the plastic washer under the handle (now on top of the faucet head) left to loosen it. Then push it back right to tighten it, reassemble the faucet and test it.
How do you fix a leaky faucet?
1:382:54How To Fix A Dripping or Leaky Double Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst take off the handle. Then unscrew the valve stem on the stem remove the old gasket screw. AndMoreFirst take off the handle. Then unscrew the valve stem on the stem remove the old gasket screw. And seat washer. Apply some plumbers grease.
Techniques for solving a tough faucet problem
Repair a drippy ball-type faucet using these pro tricks to deal with stubborn screws. You may have to replace the handle, but not the entire faucet.
Kitchen Faucet Repair: Loosen a stuck screw on a single-handle faucet
If the Allen screw is stuck, or if you strip it so it won’t come out, remove the cap with the handle still in place. You can’t grab the flattened edges with the handle in place. Instead, for this kitchen faucet repair, cushion the jaws of pliers and grip the round edge below.
How to Remove Faucet Handle
If you can’t loosen the Allen screw on the handle of a ball-type faucet, don’t let that 15¢ screw force you into a $100 faucet replacement… just yet! Normally you have to remove the handle to get the worn rubber seats that cause the drip (Figure A). First try spraying the screw with penetrating oil every day for a week.
Required Tools for this kitchen faucet repair Project
Have the necessary tools for this DIY kitchen faucet repair project lined up before you start—you’ll save time and frustration.
Required Materials for this kitchen faucet repair Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
How to unscrew a valve?
Wrap a rubber glove around the metal collar that holds the valve in place and grip the collar with adjustable pliers. Turn the collar counterclockwise to unscrew it, then remove it, lift out the ball, and set both aside.
How to soften O rings on a spout?
Drop some penetrating oil into the space between the spout housing and the valve seat. Wait about 10 minutes for it to lubricate the O-rings, then try swiveling the spout. If it doesn't move, apply more oil. You also can try pouring boiling water into the gap to soften the O-rings.
How to lubricate a valve seat?
Drop some penetrating oil into the space between the spout housing and the valve seat. Wait about 10 minutes for it to lubricate the O-rings, then try swiveling the spout. If it doesn't move, apply more oil. You also can try pouring boiling water into the gap to soften the O-rings.
How to remove old O rings from valve?
Coat new O-rings with plumber's grease, slide them over the valve housing , and work them into the grooves from which you removed the old ones. Spread a little more plumbing grease around the outside of the vale seat and the inside of the spout housing, and slide the housing back onto the valve seat.
How to dissolve a spout housing?
If you have hard water, mineral deposits may be binding the spout. Soak the spout housing in white vinegar to dissolve them before replacing the housing.
Does a peerless faucet have a ball valve?
By Chris Deziel. Peerless and Delta faucets have a similar design, because the same company manufactures both brands. That means your Peerless kitchen faucet probably has a ball valve, as opposed to a cartridge, because Delta pioneered this type of faucet. If it has a swivel spout, and the spout won't swivel, you have to remove the ball to make ...
