
Full Answer
What are the best ways to remove a pocket door?
- 1.1 Step 1: Remove the pocket door from the track
- 1.2 Step 2: Open up the wall
- 1.3 Step 3: Take out the old track to replace it with the new one
- 1.4 Step 4: Take out the remaining hardware
- 1.5 Step 5: Adjust the Replacement Hardware of the New Door
- 1.6 Step 6: Replace the Trim and Wall
- 1.7 Step 7: Put the New Pocket Door Pull
How do you replace a pocket door?
- Remove the Door and Trim. Begin by removing the door from the opening. ...
- Open the Wall. ...
- Remove and Replace the Old Track with the New. ...
- Replace the Hardware on the Door Panel. ...
- Repair the Wall. ...
- Create an opening for the Latch. ...
- Chisel the Mortise for the Faceplate. ...
How to install, adjust or remove a pocket door?
How to Replace a Pocket Door
- Removing the Door. As the first step of pocket door replacement, you will need to cut a hole in the wall for access to the rollers and the track system, ...
- Removing the Track. ...
- Shimming the Track. ...
- Replace Roller Hardware. ...
- Installing the Door and Frame. ...
How to fix a pocket door that fell off track?
- Before we jump to the conclusion that you need to cut holes into the wall, it is always a good idea to lubricate the rollers to see if this alleviates ...
- You may also want to inspect the screws that were used to hold your sliding door in place. ...
- Sometimes, even metal stud drywall screws are used. ...

How do you get a pocket door back on track?
0:351:43Pocket Door Repair by Anthony Gilardi - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the molding off first to get to the frame. Taking the frame off releases the pocket door. ThenMoreTake the molding off first to get to the frame. Taking the frame off releases the pocket door. Then once the frame is off the pocket door can be removed.
Can you replace a pocket door without removing drywall?
If you simply want to replace a pocket door or remove it in order to repair it, you don't have to tear into the drywall! That's great news. All you have to do is lift the door off the sliding track. In order to do that, you have to remove the trim around the door.
Can a pocket door be repaired?
While pocket doors work flawlessly most of the time, sometimes they come off track, get stuck, or become misaligned. Some pocket door problems can be fixed without removing trim or drywall. Most issues require the removal of trim—but it's usually only select areas of trim.
How do you remove a pocket door without removing trim?
0:171:10How to Remove a Pocket Door - YouTubeYouTubeStart of suggested clipEnd of suggested clipOlder style pocket doors ride on a J track to remove the door tilt the bottom out and lift itMoreOlder style pocket doors ride on a J track to remove the door tilt the bottom out and lift it straight up to get the wheels off the track then remove the door.
How much does it cost to fix a pocket door?
Existing Wall Pocket Door The cost to install a pocket door in an existing wall during a remodeling project ranges from $2,000 to $6,000 or more. The price will vary quite a bit depending on your project's complexity, but it typically includes wall demolition, as well as any plumbing and electrical work you may need.
How much does it cost to replace a pocket door?
It will cost you between $1,000 and $3,500 to have a pocket door installed in an existing wall. The rate charged by a professional to hang a standard model is $150 to $200.
How do you fix a pocket door that won't close?
0:4416:27How to Fix a Stuck Pocket Door - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut it back on we'll just use caulking to fill in that cut line all right here we go be careful whenMorePut it back on we'll just use caulking to fill in that cut line all right here we go be careful when you're pulling that knife across that you don't slip and go outside and for the trim.
How do you fix a sliding door that is off track?
Tips & Tricks: How to Fix 6 Common Sliding Glass Door ProblemsRemove the door from the track. First,Locate the roller adjustment screws and use a screwdriver to turn the screws counterclockwise. ... Check the rollers. ... Reinstall your clean rollers. ... Clean the tracks. ... Reinstall your door.
How do you use a pocket door wrench?
The pocket door wrench is used to adjust the bolts on the door hinges up or down. What is this? Turning the nut clockwise will raise the door, and it'll be lowered when you turn it counter-clockwise. Take care that you don't end up with a crooked door!
How do you replace the rollers on a pocket door?
0:3412:19How to Replace Rollers on a Pocket Door - YouTubeYouTubeStart of suggested clipEnd of suggested clipNot much you can do when this happens except take the door out of the pocket to see if the rollersMoreNot much you can do when this happens except take the door out of the pocket to see if the rollers came off the track or need to be changed for that to happen i need to take this trim. Off i will
How do you change the hardware on a pocket door?
Remove the Door and TrimRemove the Door and Trim.Open the Wall.Remove and Replace the Old Track with the New.Replace the Hardware on the Door Panel.Adjust the New Hardware.Replace the Trim and Stops.Repair the Wall.Replace the Pocket Door Pull.More items...
How do you put a sliding door back on track?
Angle the bottom of the door toward you while you let it down, and the wheels should hook right onto the track. Release the door and let it swing gently back to the vertical position. Check that the door will glide, then hang the other door on the front track, using the same method.
How To Repair Pocket Doors - Old House Online
Troubleshooting Pocket Doors | Pocket Doors | Interior Doors | Doors ...
How to fix sticky, noisy or just plain broken pocket doors
Do you have a pocket door that sticks or doesn't open or shut all the way? Don't replace it if you don't have to—just install a new track, new rollers or both, and your pocket door will work like it did when it was new.
Pocket Door Overview
You don’t need to be a coal miner to venture into the deep, dark pocket of a sliding door, but it helps. Once you’re equipped with a new track, rollers and a good flashlight, we’ll show you how to get in, replace the broken hardware, and get out before the weekend’s over and the search party comes looking.
Tips for removing doors
Remove painted-over screws. Cut the paint seam between the door stop and the casing, but don’t remove the casing. Pry off the door stops with a stiff putty knife. Remove the pocket door.
New track and pocket door rollers
Cut an access hole in the wall with a drywall saw to remove the old track and install a new one. Check for obstructions before pounding the saw through the plaster or drywall to start the cut.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
1. Figure Out What Kind of Pocket Door You Have
Pocket doors come in two main styles, either top-hung or a floor-track model. The former is more common, while the latter is typically something you’d see in older homes. A look up and down will tell you where you need to focus your attention.
2. Check the Rollers
This one is our first of two easy fixes. Grab a flashlight and inspect their position on the track. Sometimes, the roller may slip out, causing the door to fight you when you want to open or close it. If one or more is out of place, you can simply pop it back into the track carefully. Don’t fight it if it doesn’t budge.
3. Clean the Track
Sometimes, debris gets in the track and can interfere with the operation of the pocket door. Even small stuff can cause issues. Run a damp paper towel through its length, and try the door again. If it works, your problem is solved. If not, it’s back to the rollers.
4. Inspect the Rollers
Some models may have an adjustment screw to allow you to lower or raise the pocket door. Wood can warp over time, which can affect its fit. Seasonal effects on the shrinkage of the structure can also play a role. A clearance of about ¼” is ideal.
5. Remove the Casing Along the Top of the Door
You’ll find this task easy or a pain, depending on the number of coats of paint there are on the casing. You can use a putty knife, an all-purpose utility knife, chisel, or the end of a hammer if it’s really stubborn. However, be careful as you go to avoid damaging the frame and drywall.
6. Remove the Door from Its Track
How you do this task depends on the type of roller. You’ll see single, double, or J-style sets. Older pocket doors have a simple hanger pin that you’ll have to release first. The issue you might run into is one of adequate clearance to pop off the door.
8. Examine the Rollers
This step involves looking at the existing hardware for signs of damage. Sometimes, you’ll find a bent one is the culprit if someone forced the door open or slammed it. If it’s an older set, you might consider replacing them even if they are still intact since you have the door off, anyway.
What is pocket door?
Pocket doors are a charming feature used in many homes. These doors allow you to hide them in the wall to create a wide opening without any obstruction. The problem with these sliding doors is they may need repairs from time to time. This may leave many homeowners wondering how they go about fixing something they can’t see because it is hidden in ...
Why are pocket doors obstructed?
Sometimes pocket doors can be obstructed from opening if they are too long for the doorway opening. You may have installed carpet or tile to the flooring surface that has raised the overall floor height. This means you need to trim the length of the door – this can easily be accomplished by using a saw to plane the edge of the door to fit it to the new opening height that you now have.
How to fix top gaps in door?
Top gaps require a raising of the door. Start by adjusting the hanger on the door that is positioned the farthest away from the door latch. Use a pocket door wrench to turn the hanger a quarter of a turn at a time until the door is parallel with the jamb.
Why is my pocket door not hanging straight?
You may also notice that one of your doors is not hanging straight, which is also caused by the rollers.
How to raise a door that is too low?
Start by turning the nut with a socket on each hanger clockwise . This will raise the door up. If your door is too low, you can lower it by turning the nut counterclockwise.
Can sliding doors get off track?
One of the most common problems that occur is with the rollers. The rollers of your sliding door are comprised of two parts that tend to get pocket doors off track. The roller is attached to the base, which is joined with the door. As you use your pocket door over time, these parts may begin to separate and get misaligned. Nevertheless, you can easily adjust pocket door bases and rollers and make them functional again.
Can you raise a pocket door?
Take into account that you will only be able to raise the door to a certain degree. Too much upward height can cause the pocket latch to misalign, making it impossible to operate the door effectively. Adjusting the Hanger. Another adjustment option for your pocket door is to adapt the side movements.
How to repair a pocket door
Pocket doors are great space-savers because they conveniently disappear into the wall when opened. However, fixing a pocket door can be a hassle, as many common issues necessitate removing the trim or a section of drywall. Here’s how to go about doing this.
3 reasons to install a skylight
A skylight can be an excellent addition to almost any home. Here are three reasons you may want to install this type of window.
Lone workers face various safety issues
When we consider remote workers, we could say a lot of people work alone today. But there are those for whom the word ‘remote’ means something entirely different than the living room.
How to involve your dog in your wedding
If you’re getting married and want your pooch to be a part of the wedding, here are three ways you can incorporate your canine companion into the big day.
How to care for non-stick pans
Did you know that non-stick pans require special care? Follow these four tips to protect them from damage and wear.
Student loan payments paused again
Americans worried about repaying their student loans have gotten another reprieve with President Joe Biden extending a pause on repayment and interest accumulation until May 1, 2022. The government paused student loan repayment shortly after the onset of the COVID-19 pandemic when millions suddenly found themselves without jobs.
What to include in a reading nook
Whether it’s in your bedroom or a quiet corner of the living room, everyone deserves a cozy spot they can retreat to for some downtime. Here are a few must-haves for your reading nook.
What is the best hardware for pocket doors?
What is the best hardware to use? Metal hardware is best when it comes to pocket doors. With the use of metal, objects can be installed more solidly. Any minor mishaps can affect the mobility of the pocket door, so using solid hardware works best.
Can you attach a pocket door to a track?
Unfortunately, no. The assembly of standard pocket doors and RV pocket doors are similar. However, RV pocket doors have a latch mechanism to attach them to the track. It would help if you separated the latch mechanism first before getting to the doors’ wheels.
