How to Fix Poulan Chainsaw Troubleshooting?
- Fuel Check. Check that you are not using stale fuel, discard and empty the tank if the gas has spent over 2weeks in the saw.
- Carburettor. If the issue is a blocked carburettor, clean it thoroughly using a carburettor cleaner. ...
- Spark Plug. When you inspect the spark plug, check if it is firmly fitted in. ...
- Blocked Air Filter. ...
- Starter cord. ...
Full Answer
How to replace the chain oiler on a Poulan?
How to Replace the Chain Oiler on a Poulan
- Set your Poulan chainsaw on a flat surface and allow it to cool, if it recently was in use.
- Put on leather gloves to protect your hands from sharp parts. Remove the two nuts on the exterior, right side of the chainsaw casing with an adjustable wrench.
- Remove the screws in the top cover of the chainsaw with a Phillips screwdriver. ...
How to replace chain adjuster screw on Poulan chainsaw?
- Place the saw on a flat bench and ensure there are no obstructions around the chain, which will spin during this procedure.
- Unscrew and remove the three screws holding the engine cover and remove the cover.
- Locate the idle adjustment screw.
- Start the saw and let it idle for two or three minutes to warm up.
- Tip.
How to put new gas lines on a Poulan chainsaw?
Tips on Inserting Fuel Lines in Chainsaw Gas Tanks
- Fuel Line Basics. Chainsaw fuel lines are typically clear plastic tubing. ...
- Proper Tube Length. When it's time to replace the chainsaw fuel lines, it's important that you cut the new tubes to the proper length.
- Tools of the Trade. Using the proper tools for the job makes fuel line replacement easier. ...
- Additional Tips. ...
How to sharpen Poulan 14 chainsaw?
How to Sharpen a Poulan Chainsaw. Set the Poulan chainsaw onto a level work surface. Insert the tip of the correctly sized file into the heel of the heaviest damaged tooth. Hold the file level and steady. Rotate the chain up to the next tooth on the same side as the first.
How do you fix a Poulan chainsaw that won't stay running?
How To Fix a Poulan Chainsaw That Won't Stay RunningFix #1: Clean the Carburetor.Fix #2: Clean the Spark Arrestor.Fix #3: Unclog the Fuel Filter.Fix #4: Unclog the Air Filter.Fix #5: Use Clean and High-Quality Fuel + Check Fuel Mix.Fix #6: Adjust the Idle Screw.
How do you take apart a Poulan chainsaw?
0:145:47Teardown of POULAN 2900 Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext thing you have to do is turn the saw over reach down in here. It's going to go to the cylinderMoreNext thing you have to do is turn the saw over reach down in here. It's going to go to the cylinder head and there's an Allen bolt in there that you have to remove. So actually a motormouth.
How do you fix a Poulan chainsaw that won't start?
0:423:21Poulan Pro chainsaw won't start. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSince the fuel filter broke off the line there's going to be debris in the carburetor. So we'll haveMoreSince the fuel filter broke off the line there's going to be debris in the carburetor. So we'll have to get it out. And here you can see all the clogged debris trapped in the screen in the carburetor.
Why does my chainsaw stall when I give it gas?
Air-Circulation Before making adjustments to your carburetor's high-speed screw which is highly discouraged by most chainsaw manufacturers you should clean the spark arrestor and air filter. If any of these are dirty, then chances are they are contributing to your chainsaw stalling and you should thoroughly clean them.
How do you disassemble a chainsaw?
0:193:40Echo Chainsaw Disassembly – Chainsaw Repair Help - YouTubeYouTubeStart of suggested clipEnd of suggested clipStarting set the chainsaw on its side and remove the screws securing the recoil starter assembly toMoreStarting set the chainsaw on its side and remove the screws securing the recoil starter assembly to access the recoil pulley start a rope and rewind.
How do you rebuild a carburetor on a Poulan chainsaw?
6:287:28HOW TO Reassemble Carburetor on The Poulan 2150 Chainsaw.YouTubeStart of suggested clipEnd of suggested clipOn next you put the metering diaphragm. This way this part acing the carburetor. You line up the twoMoreOn next you put the metering diaphragm. This way this part acing the carburetor. You line up the two metal pins into the diaphragm you make sure straight like that. And then you just reassemble.
What would cause a chainsaw not to start?
A spark plug might be defective and needs to be replaced. If your chainsaw has a defective spark plug, it cannot create an electrical current to ignite the system. Remove the spark plug and inspect if it is dirty, cracked, eroded, or damaged. There may also be a heavy carbon buildup or a burned-up electrode.
Why is my chainsaw not getting spark?
0:178:32HOW-TO Fix A Chainsaw With No Spark - Ignition Module ReplacementYouTubeStart of suggested clipEnd of suggested clipIf you don't have any spark then more than likely it is the ignition module failing on you you wantMoreIf you don't have any spark then more than likely it is the ignition module failing on you you want to make sure first before you replace an ignition module.
Why does my chainsaw start and then stop?
0:052:01Top Reasons Chainsaw Starts, Then Stalls — Chainsaw TroubleshootingYouTubeStart of suggested clipEnd of suggested clipOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall.MoreOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall. You can try cleaning the arrestor with a wire brush. But you may need to replace it with a new one.
Why does my Poulan chainsaw keeps cutting off?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Why does my chainsaw stop running after a few minutes?
The most common problems why a chainsaw does not stay running are: Spark Switch/Plugs. Bad Fuel. Blocked Carburetor.
Why does my chainsaw dies at full throttle?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
How do you replace the recoil spring on a Poulan chainsaw?
2:2811:24Poulan Chainsaw Repair - How to Replace the Recoil Spring - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow we can remove the central screw that secures the hub and the pulley to the starter. With theMoreNow we can remove the central screw that secures the hub and the pulley to the starter. With the screw out of the way now I can remove the hub. And now I'll remove the assist spring.
How do you replace the throttle cable on a Poulan Pro chainsaw?
0:191:43Poulan 3818 Chainsaw Throttle Linkage Removal, Installation ...YouTubeStart of suggested clipEnd of suggested clipSo what you need to do is grab the linkage insert it in this hole like. This. Now you need to pressMoreSo what you need to do is grab the linkage insert it in this hole like. This. Now you need to press the throttle trigger. And what you need to do as well is push on the linkage.
How do you take apart a chainsaw carburetor?
1:1811:57How to Fix a Chainsaw Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd now the two nuts that secure the carburetor to the chainsaw. Body. Now I'm going to clamp offMoreAnd now the two nuts that secure the carburetor to the chainsaw. Body. Now I'm going to clamp off each of the fuel lines. And then remove them from the. Carburetor.
How do you replace the primer bulb on a chainsaw?
2:317:01Poulan Chainsaw Repair - How to Replace the Purge Bulb - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust use a screwdriver to pry it. Away. Now I can remove the primer bulb. You won't be able to seeMoreJust use a screwdriver to pry it. Away. Now I can remove the primer bulb. You won't be able to see what I'm doing on the backside of the primer bulb.