How to fix a lawnmower pull cord that is stuck, step by step
- To start, inspect your blade for any stuck strands of grass or debris. Remove them as they cause the pull cord to get stuck.
- Open the blower housing and inspect the recoil starter. If it appears damaged, you need to replace it.
- Check if the engine is hydro-locked, remove the spark plug and pull the rope repeatedly to restart the engine.
Full Answer
How to replace a pull cord on lawn mower?
Process Of Replacing A Pull Cord On Lawn Mower:
- New pull rope with exact length and thickness
- Screwdriver
- Wrench
- Needle nose Pliers
- Lighter
- Hand gloves
How to fix the pull string on a lawn mower?
- Unplug the spark plug wire before starting the repair. ...
- Disassemble the housing (the top cover) to expose the pull cord assembly.
- Remove the center bolt and cap in order to pull the pawls out.
- Inspect the pawls and determine whether they’re damaged or worn.
How to fix a broken pull rope on a lawnmower?
Tools Required
- 4-in-1 screwdriver
- Leather gloves
- Needle-nose pliers
- Nut driver
How to repair a pull cord on a Tecumseh lawnmower?
This lawn mower repair video shows the removal of the recoil assembly and replacement of the starter cord on a Craftsman Eager 1 with a Tecumseh engine.Be su...
How do you fix a broken lawn mower pull cord?
2:264:31How to Replace a Pull String on a Push Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then place the knot in the pocket on the starter pulley. Now I'm going to hold the rope andMoreAnd then place the knot in the pocket on the starter pulley. Now I'm going to hold the rope and remove the screwdriver. And slowly allow the rope to coil back into the pulley.
How do you reattach a lawnmower pull cord?
2:165:52HOW TO Replace a Broken Lawnmower Pull Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull that out now you want to tie a good knot at the end of that rope. Now pull the rope like. ThisMorePull that out now you want to tie a good knot at the end of that rope. Now pull the rope like. This pull right to the other end of the rope. Now insert the starter handle. Make a knot over.
How do you fix a pull cord that won't go back in?
0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
How do you fix a pull cord on a lawn mower that won't retract?
1:422:5510 second fix! Lawn mower pull cord not going back in recoil ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI just quite simply lifted up the lawnmower. Spun the blade backwards.MoreI just quite simply lifted up the lawnmower. Spun the blade backwards.
How do you replace a pull string?
2:033:54How to Replace the Pull Cord on a Small Engine by @Gettin' Junk DoneYouTubeStart of suggested clipEnd of suggested clipBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keepMoreBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keep spinning it over and over. Until you get to the point where you have a lot of tension.
How much does it cost to replace a pull cord on a lawnmower?
A new lawn mower starter rope causes between $10 and $20 at home improvement stores.
What does it mean when the lawn mower string won't pull?
What if the starter rope won't pull? The crankshaft is connected to the blade shaft on your recoil start walk behind lawn mower, so if the pull cord is stuck, it could be because something is blocking the movement of the blade. Disconnect the spark plug for safety, then take a look under the deck.
Why does my pull cord get stuck?
Problems With the Recoil Mechanism Sometimes the pull cord crosses over itself when rewinding, and when this happens, it can get stuck. You may be able to free it by pulling it gently to coax it out to its full length, then letting it rewind slowly.
How do you fix a Briggs and Stratton pull cord spring?
4:279:44Briggs & Stratton Recoil Starter Service - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the end of the hook is as close to the center hole as possible this will make it engage toMoreMake sure the end of the hook is as close to the center hole as possible this will make it engage to tab when you put the pulley. On slightly bend the spring in toward the hole as. Needed.
How do you fix a pull cord spring?
0:096:40How to fix a pull starter recoil spring and replace a stuck or limp pull cordYouTubeStart of suggested clipEnd of suggested clipJust kind of have to work it with your pair of pliers the most important thing is. This is whereMoreJust kind of have to work it with your pair of pliers the most important thing is. This is where it's gonna go once it's in there it's gonna go like this.
How do you fix a Briggs and Stratton pull cord?
0:007:31HOW TO Repair The Pull Cord on Your Lawnmower With Briggs ...YouTubeStart of suggested clipEnd of suggested clipBut if the rope wasn't broken and still attached to the recoil. Which you would want to do is loosenMoreBut if the rope wasn't broken and still attached to the recoil. Which you would want to do is loosen this nut here and slide the rope right through the crack.
How do I replace a frayed lawn mower cord?
You still need to remove the assembly from the mower, although it's possible to do it in place, I don't recommend it. (1) Cut the correct length of new cord, measure it against the old one. Don't remove the old cord yet.
What to do if your pull cord is hard to pull?
If your pull cord is hard to pull (stiff), make sure the bail lever is held during the starting process. I know most of you are in no doubt about how to start your mower, but for anybody that's a little rusty check out "How to start a mower".
What does it mean when a pull cord doesn't retract?
A broken cord is obvious, a pull cord that doesn't retract is usually a broken recoil spring, and a pull cord that doesn't catch and turn the engine usually means worn pawls.
How to load up a recoil spring?
If you choose not to remove the pulley, you must load up the recoil spring by turning it anticlockwise three turns. Then lock the pulley with the screwdriver as per the above guide, while you feed in and knot the cord, fit handle and double knot. Remove your locking screwdriver, check operation and refit, your done.
Why does a carburetor float needle seal wear?
This is basically a cylinder filled with gas, and because a fluid can't be compressed, the piston won't move giving you a stiff pull cord. The gas gets into the cylinder because the carburetor float needle seal is worn.
How to fix a pull start that isn't catching?
If your problem is a pull start that just isn't catching and turning over the engine. Simply remove the cap and replace the pawls. Examine all for damage including starter pulley. If your problem is a damaged spring then the pulley will need to be removed from the assembly.
What is the brake on a lawn mower?
The engine brake also know as the flywheel brake, as you know is controlled by the bail lever at the handlebars (most mowers), and it must be held to start the mower. Its function is two fold - it grounds the coil shutting down the engine and it applies a brake pad to the flywheel, not unlike a bicycle brake.
How long does it take to replace a pull cord on a lawn mower?
The mower won’t start so you yank and yank on the pull cord without success. After 15 minutes (and a few expletives 🙂 the pull cord on the mower jambs or breaks. 1.
Can you remove a pull cord from a lawn mower?
In that case, you might need to remove the pulley from the assembly. Although most pulleys don’t require removal, it may depend on the quality of your lawnmower.
How Your Lawn Mower Pull Cord Works
When you pull the rope to start your mower, it engages the starting mechanism, which turns the engine fast enough to spark the ignition module.
Lawn Mower Pull Cord Not Catching: Possible Causes
There are two very common causes for a lawn mower pull cord not catching. These include:
Can You (and should you) DIY the Fix?
If you’re handy and like working with mechanical parts, it’s pretty easy and inexpensive to replace part or all of this component on your mower.
