Repairing Guides

how to repair a rain bird sprinkler valve

by Elinore Lang I Published 2 years ago Updated 2 years ago
image

What is an anti siphon valve?

Do you need separate valve groups for sprinklers?

About this website

image

How do you repair a Rainbird irrigation valve?

0:191:59Rain Bird - Replacing the Valve Diaphragm - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst shut off the main water supply to your irrigation. System disconnect the wires to the solenoidMoreFirst shut off the main water supply to your irrigation. System disconnect the wires to the solenoid. By cutting them or by unscrewing the wire nuts turn the solenoid counter clockwise to remove.

Why is my Rainbird valve not working?

Valve opening mechanism damaged or clogged with debris. See if you can flush debris from the valve by using the flush mode. If not, turn off the water, disassemble, inspect and clean the valve (See Diaphragm Valve Disassembly Procedure).

How do you fix a Rainbird solenoid?

0:211:26Replacing the Solenoid: Rain Bird Residential Valve TroubleshootingYouTubeStart of suggested clipEnd of suggested clipFirst shut off the main water supply to your irrigation. System disconnect the wires to the solenoidMoreFirst shut off the main water supply to your irrigation. System disconnect the wires to the solenoid. By cutting them or by unscrewing the wire nuts. Turn the solenoid counter clockwise to remove.

How do you fix a leaky Rainbird sprinkler system?

0:421:47RainBird 5000 Troubleshooting Leaking Heads - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne thing you can do is just screw the sprinkler off of the fitting and run water through to makeMoreOne thing you can do is just screw the sprinkler off of the fitting and run water through to make sure that there's no dirt in the lines that are getting in the sprinklers.

How do you fix a sprinkler valve that won't turn on?

1:288:43Troubleshooting Valve Issues - YouTubeYouTubeStart of suggested clipEnd of suggested clip1 if a zone won't stop running it's all a certainly aim valve problem the kind of issue is somethingMore1 if a zone won't stop running it's all a certainly aim valve problem the kind of issue is something that would practically never be caused by controller. So in that case find and replace the valve.

How do I know if my Rainbird solenoid is bad?

Signs You Have a ProblemThe Water Won't Shut Off. If you have this problem, it's very likely the solenoid. ... Low or Uneven Water Pressure. The solenoid controls the water pressure. ... Water Leaks. There are many points in a sprinkler system that can leak. ... Current Testing. ... Valve Inspection. ... Parts Replacement.

How long do Rainbird valves last?

One of the components that you may need to replace regularly are the wires, often due to improper installation and corrosion. Valves will give you 10 to 15 years of service, while controllers 5 to 10 years.

How do you test a Rainbird solenoid?

0:114:44Sprinkler System Solenoid Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing just a good volt meter. And you've got to have it at least where you can turn it to ohms anyMoreUsing just a good volt meter. And you've got to have it at least where you can turn it to ohms any kind of meter you can just test the ohms.

How much does it cost to replace a solenoid in a sprinkler system?

The average cost to replace a sprinkler solenoid is between $85 and $150. This includes the cost of parts and labor.

Why is my Rainbird sprinkler valve leaking?

Leaking valves can be caused by a damaged gasket. There is also an O-ring on the solenoid that should be checked. Rinse off any debris on the surfaces of the parts. Dislodge debris if it is clogging any of the "ports," the tiny holes that are found in the diaphragm and the plastic base that the solenoid screws into.Changing Out the Top End of a Rain Bird Valve - Home Guideshttps://homeguides.sfgate.com › changing-out-top-end-rai...https://homeguides.sfgate.com › changing-out-top-end-rai...Search for: Why is my Rainbird sprinkler valve leaking?

Why is my Rainbird sprinkler leaking?

The sprinkler is leaking - This is normally caused by worn washers and seals. They should be replaced at this time. The sprinkler is not throwing as far as it should - This is usually caused by some type of blockage, either in the nozzle or the inlet screen.Irrigation Troubleshooting Guide - Rain Birdhttps://www.rainbird.com › files › media › documents › Ir...https://www.rainbird.com › files › media › documents › Ir...Search for: Why is my Rainbird sprinkler leaking?

What causes a sprinkler valve to leak?

The common causes of sprinkler valve leaks include broken O-rings, excess pressure, start-up or shut-down problems, damaged valves, blocked distribution lines, and damaged sprinkler heads. To solve these, replace the O-rings, use cycling valves, seal pipe joints, remove clogs, and use new valves.Diagnosing Sprinkler Valve Leaks: 8 Causes and Their Fixeshttps://landscapingplanet.com › diagnosing-sprinkler-valv...https://landscapingplanet.com › diagnosing-sprinkler-valv...Search for: What causes a sprinkler valve to leak?

How do you know if your sprinkler valve is bad?

Signs of issues in sprinkler valve:Water not turning Off: If you notice that water is not closing off from the sprinkler, then there seems to be an issue in the diaphragm valve. ... Leaks of water: ... Broken Sprinkler Head. ... Stuck Valve. ... Wiring: ... Irregular Watering:

How do you test a Rainbird valve?

0:171:00Manual operation of Rain Bird valves - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the solenoid in the on or counterclockwise. Direction about a quarter turn then wait a fewMoreTurn the solenoid in the on or counterclockwise. Direction about a quarter turn then wait a few seconds until you hear water rushing through the valve.

Why is one sprinkler zone not working?

If just one zone isn't working, the problem is usually an electrical issue or a defective controller or solenoid. To check the controller: Ensure the zone wires are firmly attached to the controller terminals, the transformer is plugged in, and the circuit breaker in the main panel is on.

How do you test a Rainbird solenoid?

0:114:44Sprinkler System Solenoid Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing just a good volt meter. And you've got to have it at least where you can turn it to ohms anyMoreUsing just a good volt meter. And you've got to have it at least where you can turn it to ohms any kind of meter you can just test the ohms.

Controller and Valve Troubleshooting Guides - Agency | Rain Bird

Troubleshooting Guides Having problems with your irrigation system? Download the Rain Bird Irrigation Troubleshooting Guide for tips, common problems and recommended solutions.

Irrigation Troubleshooting Guide - Rain Bird

5 RAIN BIRD T- Bird The T- Bird is Rain Bird’s first gear driven sprinkler. It is designed to operate in the 25-60 PSI range and cover a radius of 16-30’.

Rain Bird Irrigation Valve Manuals

JTV Series In-line Jar Top Sprinkler Valves: Manual (917 KB): Tech Spec (917 KB): CP

What is an anti siphon valve?

Anti-siphon valves have a built-in backflow device to prevent possibly contaminated water from flowing backward into the household supply. If approved by your local codes, these types of valves provide inexpensive backflow protection. Anti-siphon valves must be installed at least 6" above the highest sprinkler head on the line in order for the backflow device to work properly. Both automatic and manual versions are available.

Do you need separate valve groups for sprinklers?

Locate the manifold where you are not likely to be sprayed by the sprinklers when turning the system on manually. On larger sys-tems, separate valve groups may be required for the front and back yards. It is a good idea to keep a plan showing where all in-ground valves and pipes have been installed.

What does it mean when a sprinkler valve is broken?

A malfunctioning or broken sprinkler valve may make itself known with an area of dry grass that indicates the valve isn't turning on properly. Conversely, when a group of sprinkler heads don't turn off when they should, it also hints at a problem with the sprinkler valve. Addressing a sprinkler valve repair at the first signs ...

Why is my sprinkler valve not turning on?

Valve Not Turning On. When a sprinkler valve is not turning on, it can be due to an electrical problem, a water supply issue, or a failed solenoid. A good place to start is by ruling out a water supply problem. To do this, check the other sprinkler valves to ensure they are getting water and turning on as usual.

How to remove solenoid from valve body?

Remove the solenoid from the valve body by turning it counterclockwise, and set it aside. Remove the screws that are holding the bonnet in place. Carefully remove the bonnet, spring, and diaphragm, taking note of how they are positioned so you can re assemble the valve in exactly the same way.

Why does my valve not work when activated manually?

If the valve works when activated manually, the problem is likely due to a bad wire connection or a bad solenoid on the valve. Check the wires first. Make sure there is good contact at the point where the system wires connect to the solenoid wires and that there are no cuts or breaks in the wires. If the wires look fine, move on to ...

How to install a new solenoid?

Install the new solenoid by turning it onto the valve clockwise until it is hand-tight or it clicks into place.

What to do if your valve is damaged?

If it is damaged, replace it with a new one. Be sure to position the diaphragm in the same way as it was before, taking special care to align the dia phragm openings with the screw holes in the valve body. Position the spring and bonnet back into place .

Can you replace a solenoid in a sprinkler valve?

Replacing the solenoid is an easy sprinkler valve repair. Home centers and sprinkler equipment suppliers carry replacement solenoids for specific valve brands and models. To ensure an exact match, bring the old solenoid with you to the store.

What is an anti siphon valve?

Anti-siphon valves have a built-in backflow device to prevent possibly contaminated water from flowing backward into the household supply. If approved by your local codes, these types of valves provide inexpensive backflow protection. Anti-siphon valves must be installed at least 6" above the highest sprinkler head on the line in order for the backflow device to work properly. Both automatic and manual versions are available.

Do you need separate valve groups for sprinklers?

Locate the manifold where you are not likely to be sprayed by the sprinklers when turning the system on manually. On larger sys-tems, separate valve groups may be required for the front and back yards. It is a good idea to keep a plan showing where all in-ground valves and pipes have been installed.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9