- Identify the problem. When you sit in the chair and pull the handle, the footrest doesn’t open, and you can’t full the tension that a handle always has.
- Gathering the right tools and materials. Fixing a recliner cable or replacing a recliner cable is easy without many tools involved. ...
- Loosen the pull handle. The recliner cable is tightly connected with the pull handle. ...
- Turn the chair upside down. I suggest you place a clean cloth on the ground to prevent your chair from any damage or getting stained.
- Remove the plastic clip. There is a plastic clip in the middle of the cable attached to the metal frame on the side. ...
- Release the footrest. In order to access the cable end, you have to push the mechanism arm so that the footrest will extend and the cable end will ...
- Remove the cable end. The recliner cable end hooks to an internal lever through a hole. ...
- Install the new recliner cable. This is a reverse process of what you have done before. ...
- Flip over the chair and test it. Until now, you almost get the job done. Now you need to close the footrest and flip over the chair. ...
Full Answer
How to replace a recliner handle and cable?
This is an easy task that could also possibly turn into a replacement:
- You first need to pull the cable tight by releasing the cable stop. ...
- If you need to replace the cable, flip the chair over, and unscrew the bolts that are on the foot rest and the ones that connect the squab to the ...
- Once you remove the squab, you can replace the cable.
- Finally, attach the squab and bring the chair right side up.
How to put the back on a recliner?
- Position the brackets. Lift the back of your recliner, positioning the brackets of the back so that they are just over the brackets on the lower half of the recliner. ...
- Slid the back into place. When the brackets are aligned properly, you should be able to position the back properly as well. ...
- Replace the screws/levers/tabs. ...
How to install and remove the recliner back?
www.wikihow.com :
- First, you must access the back of your recliner chair or sofa. To do that, push it in front to expose the back.
- Lift the panel that uncovers the locking levers and find the strip attached to them. Then, strip it to locate the snap.
- The next step consists of locating the rear locking levers. ...
- The locking levers are usually made with metal. ...
How to fix a stuck manual recliner?
- Turn your recliner upside down to access the reclining mechanism.
- From here, you can find the spring that connects the footrest to the rest of the recliner.
- Using a screwdriver, remove the screws that attach the spring to the recliner, and take out the old spring. ...
How to change cable on recliner?
Where is the cable release on a recliner?
How to detach a pull lever?
How to pop in a recliner bracket?
How to unhook a cable?
How to turn down a recliner?
How long have you been using a recliner?
See 2 more
How do you fix a broken recliner cable?
1:213:44How To Install Repair or Replace a D-Pull, D-Ring, and ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe handle and cable should now be free pull the cable out of the hole. Now we simply reverse theMoreThe handle and cable should now be free pull the cable out of the hole. Now we simply reverse the process feed the replacement cable in the hole.
How do you replace the cable on a recliner chair?
0:492:36How to Replace a Recliner Handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipInsert the barrel end of the cable into its slot. Then clip the cable neck into the handle and refitMoreInsert the barrel end of the cable into its slot. Then clip the cable neck into the handle and refit the retaining clip. Securely place the handle into the hole in the furniture. And open the latch.
How do you fix a broken cable in a chair?
0:534:18How To Replace A Recliner Handle And Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the handle clear from the side of the chair. Access to where the cable meets the mechanism isMorePull the handle clear from the side of the chair. Access to where the cable meets the mechanism is via the base of the chair. So we tip the chair over so we can easily access the end of the cable.
How do you install a recliner couch cable?
7 Steps to Recliner Cable Replacement1.1 Step 1 – Remove Hook.1.2 Step 2 – Plastic Clips.1.3 Step 3 – plastic clips.1.4 Step 4 – Remove Screws.1.5 Step 5 – Remove Old Cable.1.6 Step 6 – Place New Cable in Handle Position.1.7 Step 7 – Screw & Clip into Place.1.8 Test Your Chair.More items...
How do you fix a recliner that won't recline?
0:463:41Repair a recliner - Fix Your reclining chair! - Fix your la-z-boy - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour first step is figuring out what parts you need so you're gonna flip the recliner over to get atMoreYour first step is figuring out what parts you need so you're gonna flip the recliner over to get at the bottom where you can get to the cables.
How do you fix an electrical recliner on a couch?
0:204:10How to fix reclining chair or sofa - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep 1 make sure that the power outlet is working properly you can test it by using a lamp or anyMoreStep 1 make sure that the power outlet is working properly you can test it by using a lamp or any other electrical. Device step 2 try to switch sides for the power cords.
How do you measure a recliner cable?
2:555:24How to Determine Proper Length and Fit for a Recliner Handle and CableYouTubeStart of suggested clipEnd of suggested clipInstead you measure the length of the exposed wire a sticks out past the mechanism release clip toMoreInstead you measure the length of the exposed wire a sticks out past the mechanism release clip to the end of this tip. The most common are three or five inches in length.
Can you manually recline a power recliner?
The difference between a power and manual recliner is simple: one is motorized and one is not. A power recliner allows you to recline with the simple push of a button and needs to be plugged into a wall outlet.
How does recliner mechanism work?
There typically two types of reclining chair mechanisms; one has a cable system that operates the reclining mode. The lever lifts or releases the footrest manually via a cable and the chair tilts back. Problems occur when the cable comes loose or breaks.
How do you fix a recliner footrest that won't open?
5:539:52How to Fix a Recliner Footrest (3 Easy Solutions for You) - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr a screw may be loose. 3 with your screwdriver remove anything attached to the spring like pieceMoreOr a screw may be loose. 3 with your screwdriver remove anything attached to the spring like piece smaller Springs may also be around the spring remove them as well.
Can you manually recline a power recliner?
The difference between a power and manual recliner is simple: one is motorized and one is not. A power recliner allows you to recline with the simple push of a button and needs to be plugged into a wall outlet.
How do you measure a recliner cable?
2:555:24How to Determine Proper Length and Fit for a Recliner Handle and CableYouTubeStart of suggested clipEnd of suggested clipInstead you measure the length of the exposed wire a sticks out past the mechanism release clip toMoreInstead you measure the length of the exposed wire a sticks out past the mechanism release clip to the end of this tip. The most common are three or five inches in length.
How do you open a broken recliner handle?
Just hold back the handle and there should be two little screws holding the handle onto the chair. Undo these two screws and then either turn the chair over, or tip it onto its side so you can access the underneath of the recliner chair.
How to replace a cable on a chair?
If you need to replace the cable, flip the chair over, and unscrew the bolts that are on the foot rest and the ones that connect the squab to the chair’s frame. Once you remove the squab, you can replace the cable. Finally, attach the squab and bring the chair right side up.
Why do we need a recliner?
It provides the quiet space that you need in order to process that energetic day and relax in front of the television, or to read your newspaper or favorite book. Not to mention, you have probably had this recliner for decades, and when it comes down with ...
What to do if your pull handle is broken?
Before starting, make sure the foot rest is closed: Flip the recliner over and search for the screw that goes to the pull handle.
Why do you flip a recliner over?
Before you go flipping your recliner over to check the bottom, or all out replacing your recliner, sometimes it helps to just get another person to try their hand at fixing the perceived problem. For instance, if the handle is having a hard time moving, have somebody else try to move it. It could be that the handle is slightly jammed, but a different arm is all it takes to get that stubborn handle to move again.
How many legs does a recliner have?
Your recliner is not just a chair with four legs. Instead, it has about five different key features: springs, cable, pull handle, chair back, and footrest. Within these five components, different things can get broken or in need of extra attention. We have broken down the next part of this how-to article into a number of different sections ...
How to make a spring hole smaller?
Fill up the spring holes with wood glue or toothpicks to make the holes smaller. If the springs are mounted on metal, you can tighten the attachments. As a last resort, you can buy a new mounting plate.
What is a locking lever on a recliner?
Your recliner will have one of three types of recliner backs: locking lever, which means there are brackets attached to the sides of the back (unhinge them to take off); bolted on backs, which means the back is bolted on beneath a panel on the chair back (unbolt them to remove the back); or locking tabs/catches, which means the back is locked into place (unlock the,pm by using a flathead screwdriver). For a more in-depth visual process, check out this video tutorial:
How to avoid having to replace cable?
One of the best ways to avoid having to replace the cable is to take proper care of your reclining chair in the first place. That will eke out all the use from the chair and will make your day easier.
What is the difference between a recliner and a chair?
If you want to make sure the handle, cable, and internal mechanics live a long and healthy life, taking care of it from the day you get it is important. The internal mechanism is the main difference between a normal chair and a recliner.
How to tell if a cable is a single unit?
You will see the handle with the cable attached to it. Pull it gently, and the whole cable should come out with it. The tail and the hook will also come out at the same time. It’s sort of a single unit, basically.
How to clean fabric?
Another very effective way of getting clean fabric is just using a plain old vacuum cleaner. A soft brush also goes a long way when you need to get into those nooks and crannies.
How to take out a scuba diving tail?
Find the clip and pull on it gently. Make sure to not apply too much pressure as that may cause it to break. Pull the clip to take it out.
Can you replace recliner cables?
At first, the process might look cumbersome but if you know what you’re doing, replacing recliner cables is quite easy. All you need to do is follow the steps we are going to outline here.
Can you hit up a forum about a recliner?
You can also hit up relevant forums if you want more in-depth and expert advice on the specific cable you want to get. If you find a discussion thread with the exact model of your recliner you have, then you just hit the jackpot.
How to open a recliner cable?
Access the recliner and open. Get on that side of your sofa that comprises the recliner cable. You can find a moveable steel structure. Hold it firmly, and then apply an amount of strength. Next, open it backward or in the upward direction. You have to open it to observe the recliner cable on your sofa.
How to get maximum length of recliner cable?
Pull the cable outwards from the opening. Always pull it according to the structure. Never apply excessive strength to get the maximum length of the recliner cable.
How to get a couch to move down?
Discard the cushions and pillows from the sofa. Instead, hold its sides to move it downward.
How to pull out a cable?
Pull out the cable manually after detachment of holding structures. Hold the handle section and pull it outwards.
Why remove the bottom clip of a sleeve?
Remove the bottom clip as well to ensure complete detachment of the device. Again, the pulling force is beneficial in such methods because it can detach the clips instantly.
Why remove a small device in intact structures?
Make sure no excessive part remains attached to the small device. Remove it in intact structures because the shattered pieces are challenging to remove.
Why does a plastic handle damage a vulnerable structure?
It can damage the vulnerable structure because it lacks support. Stabilize the side that comprises the plastic covering and handle.
How to change cable on recliner?
Another slight difference, in this case, you simply take out the old cable from the system first and then attach the new pull lever and the cable with your recliner. In this case, the old cable needs to be out of the system completely from the system first as in the case of a recliner with a pull lever there is not much space to insert the new cable.
Where is the cable release on a recliner?
Each recliner cable has two parts, one is the pull handle part which you pull to get your perfect reclining portion and the other part is the cable release (s-shaped part) which is located inside the recliner and you will see it once pull out your previous cable completely or you can simply notice it the new cable.
How to detach a pull lever?
The first work will be to detach your pull lever, in order to do that, you need screwdrivers and there will be two screws attached to the pull lever, so then you need to pull out the screws using the screwdriver. Once both the screws are out, the pull lever will get detached.
How to pop in a recliner bracket?
After that part is free then you need to use pliers and try to pop in the brackets free, you need to hold the pliers from the backside of the bracket and use your fingers and hold the front part of the bracket when the bracket gets detached just leave for the time being. As your new cable will have brackets with it so it is ok if you just break your old brackets. Therefore, once you pop in your bracket, your old cable is detached from your recliner.
How to unhook a cable?
The first thing you need to do is find the cable release or you can say the s-shaped part and detach it from the hole underneath. Carefully look at the path of the mechanism so that you know how the cable is placed. After you get hold of the s-shaped part, shake a little so that it gets detached from the whole down there and comes off completely.
How to turn down a recliner?
So, simply hold your recliner using both hands and turn down your recliner by 90 degrees. Be careful while turning it down if you are doing it all by yourself because you may get hurt on your feet if the recliner falls on you.
How long have you been using a recliner?
Recliners are widely used all over the world for their uncountable comfort, look, and benefits. If you have a recliner and have been using it for months or years then you must be wondering about how to fix a recliner cable. Most people fear of repairing their recliners by themselves as it may look very complicated, ...