Repairs for Scope Misalignments
- Mounting Rings When adjusting rifle scopes, hold it on a stable, flat surface so that it doesn’t move around. This will prevent any problem with sighting your scope. ...
- Adjustments for Off-Center Mounting Holes Some rifles have holes that just aren’t placed right. Bummer. ...
- Check Your Ammo
Full Answer
How to clean the inside of a rifle scope?
The Correct Way to Clean a Rifle Scope Lens!
- Dust Removal: If you need to clean your optics, first use the brush to get all the dust off the lens. ...
- Fingerprint & Water Spot ( and the like) Removal: If you have fingerprints or water spots on your lens, you will have to go further. ...
- Mud/Stubborn Stain Removal:
How to disassemble a rifle scope?
You only need to detach the scope when you have to:
- Do a deep cleaning of your scope
- Paint your scope or scope rings
- Fix scope alignment that goes beyond simple windage and elevation adjustments
- Clear out any stuck piece blocking your lens or when you spot something inside the scope tube
How to remove rifle scope?
The following are accepted terms for coatings:
- Coated: A single layer on at least one lens surface.
- Fully Coated: A single layer on all air to glass surfaces.
- Multicoated: Multiple layers on at least one lens surface.
- Fully Multicoated: Multiple layers on all air to glass surfaces.
What is the best scope for a rifle?
The flat trajectory advantage is huge. To be fair, you might not need that in a Midwest woodlot. But if you’re hunting in big, mature timber, especially later in the season when squirrels are foraging on the ground, shot opportunities can be surprisingly rangy. A 100-yard poke isn’t uncommon, and 50-yard shots are about average.
What is scope repair?
Managing Repairs Our scope repair technicians are responsible for inspecting and testing each piece of instrumentation before it is used. They are highly trained to identify malfunctioning scopes and damaged instrumentation and will initiate the repair process and loaner acquisition.
What is inside a scope?
In the front, there is a larger objective lens where light enters the scope body, and in the rear an ocular lens that focuses that light on the shooter's eye. From the eyepiece to the rear end of the scope, you have the ocular, magnification, focus, and objective lenses.
What causes a scope to be blurry?
Clearing Up Blurry Errors As you can see, most of the time, a blurry rifle scope is due to user error. It might be parallax, an out of focus scope, or mirage playing tricks on you.
Can you spray paint a scope?
1:0811:14#10MinuteTalk – Painting Your Riflescope - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo just basically take the Rings off the base with the scope inside of them and then go to paint itMoreSo just basically take the Rings off the base with the scope inside of them and then go to paint it or just keep it on the gun. And paint everything all as one like you see in front of us here.
What does U and R mean on a scope?
Following the markings on the scope or adjustments – R for right and U for up, make the appropriate adjustments to get your group where you want it. On a Leupold scope, the adjustment direction changes the point of impact.
What do the dots on a scope mean?
These dots are arranged to allow for range estimation. A trained user can measure the range to objects of known size, determine the size of objects at known distances, and compensate for both bullet drop and wind drifts at known ranges with a MIL-Dot reticle-equipped scope.
Why does my scope get cloudy when I zoom in?
If you set everything up on the lowest (And most eye-relief-forgiving) magnification, then it's likely the scope isn't set perfectly right in the rings for you front-to-back and needs to be moved to a better position so your eye is in the sweet spot of the eye box throughout the whole zoom range.
What is scope parallax?
Parallax occurs when the target and reticle are on different planes within the scope. It is detectable when you move your head or eye around while looking through the scope, and the reticle appears to move or swim around the object at which you are aiming.
Do rifle scopes have focus?
Modern rifle scopes are typically built with a focus feature that is either fixed or adjustable. Now focus is not the same as parallax, but the two features are somewhat related as they both play a role in either directly or indirectly impacting the clarity of a target.
Can a rifle scope be Cerakoted?
Yep, sure will. We use the same durable H-Series Cerakote as your manufacturer. As Certified Cerakote applicators, we mix colors the same way the factory does—by weight, calculating the perfect ratio for each color by specific density.
Can you Duracoat a scope?
0:0017:13Paint a Rifle Scope with Duracoat (USMC MARPAT) - YouTubeYouTubeStart of suggested clipEnd of suggested clipApplying a duracoat finish to a scope is pretty much the exact same process as applying it to aMoreApplying a duracoat finish to a scope is pretty much the exact same process as applying it to a rifle of course.
Does the military spray paint their guns?
U.S. Army soldiers are (without permission) painting their weapons to blend into the environments of Afghanistan and Iraq, but some have gummed up their weapons by spraying paint into mechanical parts. Early this year, the Army issued the first formal, detailed guidelines on how to paint a rifle.
Why fix a rifle scope?
Fixing a scope gives you an accurate shot at your target.
Why take a rifle scope apart?
Taking a rifle scope apart helps establish what the problem is and take necessary action. This also helps you to know the different parts that make up the rifle scope. Before going out hunting it is important to know what each part is called and its work.
How does the magnification of an erector tube work?
The magnification lens moves towards the objective lens for increased magnification.
How important is it to take care of a rifle scope?
As a hunter, it is important to take care of your rifle and gun. Despite the amount of time and money spent on keeping the rifles in a good state, little or no attention is given to the scope. Taking good care of the scope is equally important. Good quality rifle scopes last long, but there are times that frequent repairs will be a must.
Why is my scope lens scratching?
This owes to low-quality glass or poor coating. The lens can get some scratches if the coating is not adequately thick. The poor quality glass shatters easily and consequently need replacement. The windage and elevation turrets can easily damage making it hard to adjust the scope.
How does a rifle scope work?
A rifle scope is used to magnify an image by putting the image and your eye on the same optic lane. A scope achieves this via bending rays of light using lenses inside the scope. High power scopes are longer and have more lenses than low powered scopes that are shorter and have fewer lenses.
What are the components of a rifle scope?
Knowing the parts of your rifle scope goes a long way in determining the parts that need repair. A rifle scope’s basic anatomy includes the objective lens where light enters. The light passes through the small ocular lens and focuses on the eye of the shooter.
Rifle Scope Repair
There are cheap as well as expensive rife scopes out there. If your damaged scope costs several hundred dollars, it would be a shame to throw it away to buy a new one. If you learn how to repair it, you can save that money and invest it in other important things.
Parts of a rifle scope
It’s the external lens of the scope that directly faces the target and receives light from the outside environment. The bigger the objective lens, the higher the light gaining. However, the increase in size also implies a considerable increase in weight.
How to repair a rifle scope?
If you can’t get a clear image from your scope, it probably isn’t properly aligned. To check the alignment, place the rifle over your shoulder and keep an eye open in front of the eyepiece lens. Then point a target and verify that the barrel of the rifle also points in the same direction. You can also use a quality bore sight to adjust your scope.
When was the scope invented?
The scope in various forms has been with us since the early 1600’s when a Dutch inventor Hans Lippershey was accredited to the first known telescope. Then over the years there were numerous developments of optical lenses, the most significant was the achromatic lens (two part lens- Crown and Flint). Although patented by John Dolland in 1753 if was in fact an amateur optician Chester More Hall who in 1733 proved Newton’s statement incorrect “that chromatic aberration correction through a lens was not possible”. This significant development in optics allowed for wave lengths of light which have different focal properties to diminish the effects of light scatter to be more controlled and thus reduce chromatic aberration. This then led onto the apochromatic lens which coincidently was developed and patented by Peter Dolland (John Dollands son) in 1763. These developments in lens correction and the increase of uninterrupted light transmission lead us into the basis for all optical systems of rifle scopes, as we know today.
What are some misconceptions about buying a scope?
but more often the question asked is it nitrogen filled.
What materials were used to make the first sighting cross?
The reticle which was first produced used primitive materials such as spider webs or even horse hair to obtain the sighting cross. Then with the advent of the industrial revolution materials were able to be produced with greater accuracy and treated steel wires of less than 1/25inch (.040mm) were used.
Why do you need a lens cap?
Lens caps are always a good option when walking through the scrub to help stop dirt getting onto the lens and also (providing it’s a cap with no colour cover screen) stops the suns rays from entering the tube and causing heat build up. At the end of the day the objective lens is just like a magnifier lens.
How to clean a lens?
Never clean your lens with your handkerchief. Always gently blow to remove any grit or particles with your mouth or preferably use a puffer brush (available from camera stores). It’s these small particles that cause the minute scratches on the coated lens and if not removed, just get rubbed in again and again and thus change the refractive order of the lens.
What type of reticules were used in the early Malcolm scopes?
The first types of reticules that were used in the earlier Malcolm scopes were just a rudimentary fine wire vertical post soldered onto a brass ring and inserted into the tube. They then found that by adding a horizontal wire which crossed the post this gave the marksman a better orientation.
Why is nitrogen used in lens coating?
Also due to its high purity nitrogen is drier than air and it is less likely to cause corrosion and prevent moisture damage to the coated lens surface . The manufactures use many different ways to inject the nitrogen into the tube. It may be drawn through via a vacuum line into the tube and then pressurised.
How to disassemble a scope?
In this article we are going to go over the basics of what you need to do to disassemble your scope. But first, you will need the following: 1 A lens cloth 2 A hex wrench and/or any scope specific tools 3 A workplace where you can keep all of the parts 4 Tweezers for working with small parts (optional)
What to do before putting scope back on?
Before you put the scope back on you want to wipe it down once more. We recommend using a clean cloth for this as it could affect your ability to shoot. Smudges, smears, and debris on the lens could cause err to your aim.
How to zero in scope?
After you have done this chances are that you have changed the windage and elevation. Go through the standard process of zeroing in your scope. Set up your rifle on a target, take three shots, and adjust the aim point. Continue to do this until you have zeroed your scope in.
What does it mean to level a scope?
We wrote an article on how exactly to level your scope. Essentially it means ensuring the axises on your scope are properly aligned in comparison to the rifle.
How many hex bolts do you need to remove a scope?
Usually this is an incredibly easy process that requires you to remove two to four hex bolts. Set the hex bolts to the side with the rings that hold the scope in place. We recommend giving the whole body a light dusting at this point just so you are not getting anything on the inside of the scope while you work.
Should you put pieces on paper?
Some people find it helpful to put pieces on a piece of paper in the order that they came out of the scope . Any pieces that belong as a group should be grouped together. Another point of caution is to ensure that you are careful with each part. Many of the parts inside the scope are delicate.
Can you disassemble a rifle scope?
But it is only a temporary fix and if you do not fix the overall problem, you may end up damaging the scope further. This is where disassembling a rifle scope comes into play. Disassembling a rifle scope is a relatively easy task as long as you are capable of paying attention to detail and taking your time.
How to clean a scope lens?
A: Carefully clean the lens and eyepiece with an optical cleaning solution or rubbing alcohol, then use a cloth to dry it off. You may also need to adjust the magnification level in order to see more of the target area at once. You may want to try looking at the target area through your scope from a different angle.
How to remove crosshair from scope?
Use a small piece of tape to remove the crosshair from your scope. Clean off any residue left behind by the adhesive on the bottom of the crosshair; this will make future removal easier. Once your crosshair is removed, use a hairdryer to heat up the adhesive and melt it. Use a small flathead screwdriver or blade to pry off any remaining pieces ...
Why does my scope have crosshairs?
A: The most common cause for scope crosshair issues is a dirty or scratched lens on the eyepiece. This can be cleaned with an optical cleaning solution or rubbing alcohol, and a cloth. Another possibility could be that you need to adjust your magnification level in order to see more of the target area at once.
What is a PDA scope?
This is a reticle where you input your specific information about the target into the scope, and it will calculate everything for you, including distance and wind speed. All that’s left after adjusting is to pull up on the trigger when ready!
