Sloan Flushmate Troubleshooting Guide
- Make sure the water supply valve is fully open.
- Check the Actuator adjustment. The Flush Rod (I) or push button should not interfere with the Actuator. ...
- Check Inlet Screen Turn off the water supply valve. Flush the toilet to relieve the pressure. Disconnect the water supply line from the Supply Shank (A). ...
- Remove, examine, and reinstall the Flush Valve Cartridge (3). Turn off the water supply valve and flush the toilet to relieve the pressure. ...
Full Answer
What to do if your Sloan Flushmate is leaking water?
If the leak continues, the flush valve cartridge on the Sloan Flushmate system may be defective. If the water supply static pressure and water flow are good, check the flush valve operation. Pour a small amount of water into the flush valve cartridge housing.
What is a Sloan Flushmate toilet?
The Sloan Flushmate toilet is a pressure-assisted flush system. As the tank fills with water, it traps air inside the bladder. The rising water in the tank compresses the air. When the flush valve actuates, the trapped pressurized air pushes the water in the tank into the bowl.
How much does it cost to repair a Sloan Flushmate system?
How Much Does It Cost to Repair a Sloan Flushmate System? In general, to replace the entire Flushmate system in your Sloan toilet will cost between $150 and $170 for the parts. If you have a plumber install the new parts, the cost will go up by what the plumber charges to do the work.
How do you troubleshoot a Flushmate toilet?
Check Inlet Screen. Turn off the water supply valve. Flush the toilet to relieve the pressure. Disconnect the water supply line from the Supply Shank (A). (See Figure 6) Examine the inlet screen and remove anything that may be blocking the flow of water into the FLUSHMATE® tank.
How do you fix Sloan Flushmate?
2:383:57Flushmate Trouble Shooting Video from AirDelights.com - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd flush the toilet unscrew. The air inducer cap and remove the duckbill valve from inside the capMoreAnd flush the toilet unscrew. The air inducer cap and remove the duckbill valve from inside the cap to remove any obstructions. No tools are required as this cap should only be finger tight.
Why does my Sloan Flushmate keeps running?
A run-on condition may be caused by insufficient water pressure, an improperly adjusted Flush Valve Cartridge, or a clogged inlet screen. Refer to "Installation Requirements" for recommended minimum pressure. (See "Points to Remember" for a simple method to determine whether your water pressure is adequate).
Why is my Flushmate not flushing?
Inadequate water pressure, an improperly adjusted Flush Valve Cartridge, a clogged inlet screen, or insufficient air draw may cause a weak, sluggish, or no flush condition. Make sure that the water supply valve is fully open. Check for proper actuation adjustment, see Condition A-2, "Water runs and will not shut off."
How do you stop a Flushmate toilet from running?
1:344:59Sloan Flushmate Toilet Running and Cartridge Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipRunning then you will need to tighten the cartridge down some more my toilet is still running. So I'MoreRunning then you will need to tighten the cartridge down some more my toilet is still running. So I'll use the cartridge wrench and adjustable wrench to tighten the cartridge.
How do you fix a pressure assisted toilet?
InstructionsEmpty the Tank. Shut off the water by closing the shutoff valve on the water supply line under the toilet. ... Remove the Tank Bolts. ... Install the New Tank Bolts. ... Replace the Gasket (Optional) ... Reinstall the Tank. ... Check for Leaks.
Should there be water in the tank with a flushmate?
WHY IS THERE STANDING WATER INSIDE THE CHINA TANK? FLUSHMATE units can emit a few drops of water inside the tank during the flushing cycle. This water collects on the bottom of the china until the water level reaches the height of the built-in drain. Normal level of water is about 1-inch.
How long do pressure assisted toilets last?
It may be worth the investment however, because many low-flow toilets with a pressure-assisted function can last up to 30 years! This also means that over the course of that time a homeowner can save up to $3.5k on water bills alone!
How does a Sloan flushmate work?
How it works. The Flushmate system traps air as it fills with water, uses the water supply line pressure to compress the trapped air, forces water into the bowl, and effectively pushes waste out.
Can you replace a flushmate with standard?
This Sloan Flushmate M-102540-F3A is the replacement tank for American-Standard 2045.013 one-piece toilets. This kit includes everything you need to easily replace your Flushmate system.
How do you test and replace flush cartridge of flushmate?
0:113:13How to Test and Replace: Flush Cartridge of Flushmate - YouTubeYouTubeStart of suggested clipEnd of suggested clipArea turn on the water supply. If you see a steady flow of bubbles coming from the center of theMoreArea turn on the water supply. If you see a steady flow of bubbles coming from the center of the cartridge area that means the cartridge has a leak and should be replaced.
How do you change the battery in a Sloan flush valve?
1:202:20Sloan Optima Flushometer | Batteries | Repair and Replace - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst use a seven sixty fourths inch hex wrench to unscrew and remove the cover. Now disconnect theMoreFirst use a seven sixty fourths inch hex wrench to unscrew and remove the cover. Now disconnect the sensor module. Next unscrew the battery flap. Remove the batteries and check for any leaks.
How do you fix a flushometer?
0:421:59How to Repair a Flushometer on a Toilet - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the water off from this point. Then you can use a large pair of pliers a pipe wrench removeMoreTurn the water off from this point. Then you can use a large pair of pliers a pipe wrench remove your top cap. Below the top chrome cap is going to be a plastic.
How do you reset a Sloan automatic flush valve?
2:564:10Troubleshooting a Sloan Optima Flushometer | Repair and ReplaceYouTubeStart of suggested clipEnd of suggested clipIf you don't hear a click then hold down the button and release after 40 seconds. If there is noMoreIf you don't hear a click then hold down the button and release after 40 seconds. If there is no flashing red light after 40 seconds then remove the cover check the position of the batteries.
How do I stop my automatic toilet from flushing?
Hold the toilet paper against the panel with your weak hand, with the top of the toilet paper over the gap you identified in Step 1. Use your fingertips of both hands to crinkle the paper into the gap. Continue pressing the toilet paper into the space until the toilet paper remains in place.
How do you change the battery in a Sloan flush valve?
1:202:20Sloan Optima Flushometer | Batteries | Repair and Replace - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst use a seven sixty fourths inch hex wrench to unscrew and remove the cover. Now disconnect theMoreFirst use a seven sixty fourths inch hex wrench to unscrew and remove the cover. Now disconnect the sensor module. Next unscrew the battery flap. Remove the batteries and check for any leaks.
How long is Sloan flushmate warranty?
As mentioned above, Sloan Flushmate uses air pressure in order to flush a toilet. When you purchase this kind of system, it is under warranty for 10 years. If any part becomes defective within this period, it can be changed free of charge. In addition to that, the tank has a lifetime guarantee.
What is the need for low consumption toilets?
Answering the need for low consumption toilets is Flushmate. Using pressure-assist technology, Flushmate’s toilets are able to harness the pressure from the water supply line in order to provide the energy needed to complete a flush. But despite its quality, Flushmate toilets are still prone to common problems like leaking.
What happens when a nut is loose?
When a nut becomes loose, water inside the tank may leak out of the bolt holes located in the tank. A simple fix would be to tighten the nuts – that’s usually enough to eliminate the leak. When water leaks from the gasket.
How to tell if a toilet is leaking?
When water is around the base of the toilet. When you see water around the base of your toilet, try to determine the source of the leak first. If you can’t find the source, the leak might be at the drain connection located under the bowl. You can verify this if you smell sewer gases.
Where does a toilet leak?
Now, a toilet can leak from different places but the area between the tank and the bowl is the most common. Here are areas where water may leak and how to fix them:
Is Sloan flushmate good?
Sloan Flushmate toilets are of generally good quality, but leaks are known to happen. Determining the source of the leak lets you know how to fix the problem. gif (1×1) Post navigation. Toilet Wax Seal Leaking: Tips For Repairing It How to Fix a Leaking Shower Head.
How to check a Sloan flushmate?
Step 1 – Make sure the Water Supply Valve is Fully Open. Step 2 – Turn the Water Off and Flush the Toilet. Step 3 – Check the Water Inlet Filter Screen. Step 4 – Turn on the Water and Test the Flushmate System. Step 5 – Check the Air Inducer.
How Much Does It Cost to Repair a Sloan Flushmate System?
In general, to replace the entire Flushmate system in your Sloan toilet will cost between $150 and $170 for the parts. If you have a plumber install the new parts, the cost will go up by what the plumber charges to do the work.
How much does it cost to replace a Sloan toilet flushmate?
In general, to replace the entire Flushmate system in your Sloan toilet will cost between $150 and $170 for the parts. If you have a plumber install the new parts, the cost will go up by what the plumber charges to do the work.
How to check if a Sloan toilet is recalled?
To check the Sloan Flushmate website, you can visit this link. To check by phone, call the Sloan recall hotline at (800) 303-5132 during normal business hours, Monday through Friday. In most cases, if your Sloan Flushmate toilet is part of the recall, Sloan will ship you the necessary replacement parts free of charge.
Why is my Sloan flushmate recalled?
Older Sloan Flushmate systems have a history of failures in the tank bladder. A failed tank bladder can leak water under pressure causing water to escape around the tank lid. These types of leaks and bladder failures eventually caused Sloan to issue a recall on some models of the Flushmate toilet.
What happens if a Sloan flush valve leaks?
If the leak continues, the flush valve cartridge on the Sloan Flushmate system may be defective. If the water supply static pressure and water flow are good, check the flush valve operation.
Why does my flushmate system work erratically?
If the valve is only partially open, a water flow restriction can cause the Flushmate system to operate erratically. After you close and fully open the water supply valve, flush the toilet, and see if your leak or the flush problem persists.
How to contact Flushmate?
Call Flushmate at 1-800-533-3450 for assistance.
What to use to clear a trap?
Use a plunger and auger to clear any blockage from the trap and waste line.
How much space between actuator and plunger arm?
Adjust the gap between the actuator and the plunger arm to approximately 1/8” (3 mm).
