The following are the essential steps that you should follow:
- Locate the two screws at the back This is the first step when repairing a slow close toilet seat. ...
- Centre the toilet seat on the toilet If you realize that the seat was loose, you can then wobble it back and forth so that it can be in ...
- Tighten the bolts
Full Answer
What is the best soft close toilet seat?
The 10 Best Soft Close Toilet Seats are:
- Bath Royale BR237-00
- Kohler K-4636-0 Cachet
- Bath Royale BR606-00
- Mayfair 1847SLOW 000 Kendall
- Brondell LumaWarm
- Delta Faucet Morgan 811903-WH
- Toto SS114#03 Transitional
- Kohler K-4734-0 Rutledge
- Mayfair 1830CHSL 000
- Hibbent Premium Toilet Seat. The Bath Royale MasterSuite is a high end toilet seat that we strongly recommend. ...
How to easily fix a loose toilet seat?
Method 1 Method 1 of 2: Tightening the Seat
- Find the screws and pry up the cover. The back of your toilet seat is usually connected to the toilet with two long screws that run through the porcelain ...
- Center the toilet seat on the toilet. If the seat is loose, then it may wobble back and forth, in and out of alignment with the rim of the ...
- Tighten the bolt. ...
- Apply tension. ...
How to fix a toilet that comes on by itself?
- Wait 10-15 minutes, as some water might drain on its own.
- Place your plunger into the toilet bowl and rest the mouth of the plunger into the mouth of the toilet drain.
- Softly push the plunger into the mouth of the drain, and then give a few stronger pulses to heave the debris down the drain.
- Repeatedly plunge a few times until the drain is clear.
How do you clean a soft toilet seat?
- Grab your supplies; this makes it easy to reach out for them when you need anything.
- You can either use a stain remover; we highly recommend the Instant Mold and Mildew Stain Remover. ...
- For the bleach, you remove the toilet seat from the toilet and soak in bleach and water solution, after a few minutes, scrub until the stains are removed. ...

Can a soft-close toilet seat be repaired?
Tip: If your soft-close toilet seat's hinges are not adjustable, you can replace them with a new set, which costs less than $15 USD, to make your seat work like new again. You could also replace the entire seat for around $50 USD or less. Use your fingers to push the hinge dampers back into the hinge assembly.
Why do soft-close toilet seats stop working?
Why Is My Soft-Close Toilet Seat Slamming? Soft-close toilet seats have hinge dampers that help control the speed at which your seat closes. If your slow-closing toilet seat is slamming shut, chances are these dampers need tightening.
How do you tighten a soft-close toilet seat?
0:461:35How to tighten a loose toilet seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe caps and using a Phillips head screwdriver the longer. The longer the screwdriver the better itMoreThe caps and using a Phillips head screwdriver the longer. The longer the screwdriver the better it makes it easier to type you simply tighten.
How do you replace a soft-close toilet seat cylinder?
0:032:27How to change the soft close cylinders on a Pressalit toilet seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd generally if you put a small screwdriver. In that's what's going to pull that out but you needMoreAnd generally if you put a small screwdriver. In that's what's going to pull that out but you need to lift the see and it's only when you're in a certain position that they will release.
Why is my soft-close toilet seat slamming?
Soft-close toilet seats slowly lower when tilted forward. This prevents them from slamming down, which could damage the toilet seat and hinges or wake sleeping members of the family. Dampers control the soft-close action, and these may need to be adjusted or replaced if the lid suddenly starts slamming closed.
How do soft-close hinges work?
A soft-close hinge is a type of hinge that features a hydraulic mechanism built into it. When you close the cabinet door, the hydraulics take charge and ease the door closed in complete silence in somewhat of a gliding motion.
How do you tighten a toilet seat with no access underside?
In these situations, you can hold the nut in place with a pair of pliers while using the screwdriver to tighten the bolts. The wing located on the nut will prevent the bolt from turning back on itself by locking it in place. Again, keep tightening the bolt until the seat feels secure.
Why won't my toilet seat tighten?
0:111:24How to fix a loose toilet seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese bolts are loose and once tightened the toilet seat won't slide around the toilet bowl anymore.MoreThese bolts are loose and once tightened the toilet seat won't slide around the toilet bowl anymore. The first thing I need to do is remove the plastic covers that are over each bolt.
How do I stop my toilet seat from moving sideways?
How to Fix a Loose Toilet: Locate and install seat stabilizers. Then install a set of toilet seat stabilizers, such as Safe-T-Bumpers. Loop the rubber band around the toilet seat and center the stabilizers so they touch the inside rim of the bowl. Drill a starter hole and secure the stabilizers with screws from the kit ...
How do you remove a hidden bolt from a toilet seat?
1:523:10How to fix a toilet seat with hidden fixings - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see there there's a little screw on the top. And we need to tighten up that screw. So we canMoreYou can see there there's a little screw on the top. And we need to tighten up that screw. So we can take a phillips head screwdriver.How to fix a toilet seat with hidden fixings - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you remove a hidden bolt from a toilet seat?
Why does my toilet moves side to side?
If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side. This problem can develop over time, such as when the wax seal becomes faulty or when a surrounding floor settles a little.
How do I fix my Kohler slow close toilet seat?
0:091:37Hinge and Damper Replacement - Quiet-Close Toilet Seats - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pull up on the bottom cover to remove. Next take your needle nose pliers. And pull each damperMoreAnd pull up on the bottom cover to remove. Next take your needle nose pliers. And pull each damper inward to release the hinge assembly from the toilet seat.
What are the Advantages of Repairing a Slow Close Toilet Seat?
If your slow close toilet seat has issues, it can be repaired. You should consider the above-mentioned ideas so that everything can be successful. If you do not have time, you can hire a plumber to do this for you. The good news is that a plumber is more skilled and competent in this area. He or she is likely to give you ideas that can be helpful in the long run. Also, you will be able to save more time. By repairing the slow close toilet seat, you will be able to enjoy several advantages. These include:
Why is it important to install a slow close toilet seat?
If you have small kids in your home, you should consider installing this toilet seat. This can help prevent them from getting hurt when closing the toilet bowl.
Where are the screws on a slow close toilet seat?
Locate the two screws at the back. This is the first step when repairing a slow close toilet seat. These screws are normally located at the back of the toilet seat. They normally run through the porcelain at the back of the toilet bowl. If you check keenly, they are normally held in place by two nuts at the base.
What type of screws do toilets use?
If you invested in a relatively cheap toilet, you will note that the screws are normally made of plastic. However, you will note that most toilets usually use steel screws. More expensive models usually have brass or stainless steel. If you find a plastic screw, you should be more careful with them. 2.
What makes a car seat slide side to side?
Presence of loose hinges that can make the seat to slide side to side.
Why do you weigh down a seat?
Weigh down the seat in place so that it stops wobbling as you do your work.
Can a toilet seat slam the toilet bowl?
If this toilet seat is faulty, it might keep on slamming the toilet bowl from time to time. This is not right. Over time, your toilet bowl can get damaged, and this can be very detrimental. Replacing the entire toilet bowl might make you dig deeper into your pocket. To mitigate this situation, you should ensure that you repair the soft close toilet seat whenever it is faulty.
How does a soft close toilet seat work?
Some soft-close toilet seat hinges can be adjusted to make the seat close more slowly.
How to install a soft close seat?
Place the soft-close seat upside-down on a flat surface. Flip the seat over so that the hinge assembly is exposed. Lay it down on a flat surface with the hinges facing you.
Why adjust soft close hinges on toilet seat?
The only reason you would need to adjust soft-close hinges is if your soft-close seat is not closing at the right speed. ...
What type of hinges are used on a soft close toilet?
Metal peg-style hinges are 1 of the 2 main types of hinge assemblies that soft-close toilet seats may use. Look for metal pegs coming up from round plates attached to the back of the toilet bowl, which the hinges on the toilet seat slide onto.
How many positions can you put dampers in a toilet seat?
Depending on the specific soft-close toilet seat you have, there might be 2-3 different positions you can set the dampers in to control the speed of the seat.
How to remove a toilet seat that is unable to slide off?
If you are unable to slide off the toilet seat, you might have to unscrew the bolts from underneath on the back side of the toilet bowl to remove it . Soft-close toilet seats with clip-on hinge assemblies can have slightly different attachment methods, depending on the specific make and model.
How to get a seat off a peg?
If you can’t slide the seat off the pegs, try pressing in the hinges with your thumbs and lifting it off. Different soft-close seats with peg-style hinge assemblies may have different locking mechanisms.
Why do toilet seats have a soft close?
Soft-close toilet seats slowly lower when tilted forward. This prevents them from slamming down, which could damage the toilet seat and hinges or wake sleeping members of the family . Dampers control the soft-close action, and these may need to be adjusted or replaced if the lid suddenly starts slamming closed.
How to remove a Kohler quiet close toilet seat?
On a Kohler Quiet-Close seat, start by removing the gray cover. Push upward on the two recessed areas on the side of the cover to lift it out. Next, use needle-nose pliers to grasp the "X" on the end of each cylinder and pull inward. This will allow the entire damper assembly to separate from the toilet seat.
How to remove soft close damper on Kohler?
On some models, you might see a small hole on the dampers. Insert a screwdriver into this hole and rotate the damper toward you, then slide it outward to remove it. On a Kohler Quiet-Close seat, start by removing the gray cover.
What does damping grease do to a toilet?
Damping grease will absorb shock and increase resistance when the toilet lid shuts, slowing it down. Advertisement. The damping grease needs to be applied to the inner structure of the soft-close toilet seat dampers. Look for a retaining nut on one end of the damper and remove it with a socket wrench ...
What Is a Slow Close Toilet Seat?
A slow close toilet seat is basically one that closes on its own as soon as you start to push it down.
Why are toilet seats slow closing?
Keep Things Cleaner. Slow close toilet seats are more sanitary too. That’s because there is a little less touching and handling of the seat to get it closed. That means fewer just “dirtied” hands grabbing the lid; but what’s better is that many models come with removable toilet seat hinges.
What is a lift off toilet seat?
Sometimes referred to as “lift-off” toilet seat hings, this design allows you to clean more easily around the toilet seat hinge area. We all know how difficult that is!
How to get a seat to close?
To get the seat on its way to closing, even just a light tap will do the trick. After a few seconds, the seat and/or lid will come to rest like a small feather landing on the floor.
What to do if you see cracks in Mayfair hinges?
If you see a visible crack or pieces that have come a part from the hinges, then it’s time for a replacement hinge. Simply call the number mentioned above for Mayfair/Bemis.
Why is my slow close seat not working?
Slow Close Seat Not Working. In most cases, a slow close seat that is coming down too fast just needs to be cleaned. This means from the inside out. Over time, particles from usage can become lodged in and around the moving parts of the hinge.
Does Bemis sell soft seats?
Bemis brand also sells these, including soft-seat varieties. User experience show however that the Bemis parts don’t last as long.
