
- Use a hand trowel to dig up the area above the sprinkler line. A shovel can break the sprinkler system even further.
- Cut a square patch with a shovel over the break if the line is buried. ...
- Remove the patch with 2–3 inches (5.1–7.6 cm) of dirt on the roots. ...
- Dig carefully around the sprinkler line to expose it. Once you’ve remove the patch of grass, you will be left with a clean square of earth above the break ...
- Clean off the section of exposed pipe with a wet cloth. ...
How to tell if your sprinkler system needs repair?
The water sprinkler controller stops working
- * Problem: The controller isn’t turning off. Check that the wires aren’t pushing against the relay or switch and that those leading to the switch are attached.
- * Another problem: The controller is not keeping proper time. ...
- * Mixing heads with different pressure ratings and precipitation rates. ...
How do you repair a leaking sprinkler pipe?
- Unscrew the coupling nut joining the P trap with the pipe draining from the sink. ...
- Following the manufacturer’s instructions, wrap a length of plumbers tape around the threads of the pipe.
- Move the P trap back into position with the draining pipe and reconnect the pipes with the coupling nut. ...
- Run water to check if the seal holds.
How to repair a broken PVC sprinkler pipe?
Steps
- Ensure you have all the required supplies. Nothing is worse than having to run to the hardware store in the middle of a project.
- Find the rupture. Usually a soggy area of grass, but sometimes it is a geyser.
- Turn off the sprinklers, if you don’t this could be a very hard task.
- Dig up the pipe. ...
- Cut the pipe. ...
How to fix and replace a broken sprinkler head?
Part 2 Part 2 of 3: Replacing the Sprinkler Head Download Article
- Unscrew the faulty sprinkler head from the riser. The riser is the small pipe that connects the sprinkler to the water line.
- Buy a replacement sprinkler head that's the same size as the old one. ...
- Wrap a length of thread seal tape around the male end of the riser. ...
- Screw on the new sprinkler head. ...
How to tell if a sprinkler line is leaking?
How to find a leak in a sprinkler system?
Where is the break in the water line located?
How to stop water from leaking in a water line?
How to extend a plastic pipe?
What does a larger break in a system mean?
Where to get a slip coupling for a pipe?
See 4 more
About this website

How do you fix a broken sprinkler line?
2:175:32How to Fix A Broken Lawn Sprinkler line - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd that's not a problem. And just behind that pipe you can also see that I've got a wire there. AndMoreAnd that's not a problem. And just behind that pipe you can also see that I've got a wire there. And that's the control wire for the sprinklers. Now fortunately I didn't hit that wire.
How do you fix a broken PVC sprinkler pipe?
0:253:543 Ways to Repair PVC Irrigation Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip theMoreSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip the coupling over one section of the pipe. And then over the other tighten. The nuts.
How do you fix a broken sprinkler pipe under concrete?
Swab one end of the pipe with PVC glue and then press a PVC coupler onto the end of the pipe. Swab the end of the exposed section of pipe that you cut from with PVC glue and press the other end of the coupler onto the pipe. This will seal the connection on one end of the concrete.
How do you replace a broken section of PVC pipe?
1:204:03How To Repair PVC Pipe Using a Slip Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut out the damaged section of the pipe. Making the cuts as straight as possible remove any burrsMoreCut out the damaged section of the pipe. Making the cuts as straight as possible remove any burrs and clean both ends of the pipe as. Needed. Now go ahead and install the coupling on to the slip fix.
How do you fix PVC pipe without cutting it?
PVC Pipe Repair Using Epoxy: Repair Epoxy is used to bond with both PVC pipe and joints, and it comes in both putty and liquid forms. Utilize a clean cotton cloth to clean and dry the pipe well. The epoxy will bond with the pipe and fittings only when dry and clean.
How do you glue PVC sprinkler pipes?
0:025:32How to Repair pipe in concrete slab - fixing broken, repairing ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to put your tip. In here and then rotate it until it it aligns with the head so just likeMoreYou want to put your tip. In here and then rotate it until it it aligns with the head so just like that until you feel it. There he goes and push.How to Repair pipe in concrete slab - fixing broken, repairing ... - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you fix PVC pipe in concrete?
What is the best PVC pipe glue?
0:121:33EASILY Repair Broken PVC Irrigation Pipes (UNDER CONCRETE)YouTubeStart of suggested clipEnd of suggested clipIn so this was really easy i put the shark bed on i twisted this on and now i can literally flexMoreIn so this was really easy i put the shark bed on i twisted this on and now i can literally flex that on put pvc glue on that and collar. Done.EASILY Repair Broken PVC Irrigation Pipes (UNDER CONCRETE)https://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you fix a broken PVC pipe under a driveway?
How to Repair a Line Break in an Irrigation System
If you suspect that you have a line break in your irrigation system, you'll need to locate the exact pipe that is broken in order to repair it. First, determine whether the line break is in a main "constant pressure" line or a lateral "zone" line. The main line is the pipe that delivers ...
How to stop water from pouring out of pipe?
Clean the pipe. Some water will come pouring out at first, you could try to catch it, but it is easier to bail it out. Once the water stops coming out, clean both ends with a rag. ...
How to put PVC connectors together?
If you are lucky enough to have PVC then you just put the PVC primer and glue on the outside of the pipe and inside of the straight connectors and slip them together. Work quickly because the glue sets fast. Then put the section you just glued in the gap you just created, repeating the gluing procedure. If you have metal pipes you will have to thread the outside of the pipe to fit the connectors rather than gluing them.
How long should a PVC pipe be?
Or you can buy a PVC fitting from most home improvement stores that has one pipe sliding inside an outer barrel with an O-ring inside. It will extend almost 3" in length. You may see in stores 1/2" to 2 1/2" in diameter sizes.
What is a main line break in a lawn sprinkler system?
Lawn Sprinkler Repair: Main Line Break. Lawn sprinkler repair is something that can be tricky if you are unaware of what exactly is wrong with your sprinkler system. However, if it is a main line break, then there are a few things that you will need to do before you can actually fix the problem.
What to do if your main line breaks?
If you happen to have a main line break, then you will need to make sure that you shut the water off completely. From there, you will need to get a hole dug into the ground with a shovel. Make sure to remove all of the soil and the sod that is in the area where the water was pooling up. You will then need to figure out what kind of pipe is broken.
Why does my pipe break?
Once you have the pipe exposed, you will need to look over it to figure out what made the line break in the first place. A lot of the time the causes include extremely cold weather, freezing or frost can easily bust a pipe. It could also be holes or cracks caused by aerators or other types of equipment.
How to replace a busted pipe?
You will need to measure the area that is busted and mark it. Then use pipe cutters to cut the area that needs to be replaced. Use a pipe clamp on either side of the new fitting.
How to expose a PVC pipe?
You will need to get the pipe completely exposed by removing all of the soil surrounding it. If the line break happens to be on a poly pipe, you will need to get about 2 feet of the length exposed. About 3 inches of soil will also need to be removed on either side of the exposed section. If it is a PVC pipe, then you will expose 2 feet in length and 6 inches on either side.
What happens if you break a main line?
If there is a break that it is in the main line, there will be water pooling and leaking in large amounts. This will happen even when your system is not turned on. However, if there is a break in the lateral line, then the water will leak and pool up to the surface only whenever the system is on.
What happens if a line breaks in a lateral zone?
If there is a break that it is in the main line, there will be water pooling and leaking in large amounts.
How to tell if sprinkler pipe is broken?
Another indicator of a broken pipe is if you noticed little water pressure present, or no water coming out at all, on two interconnected sprinkler heads.
What does it mean when you find a broken sprinkler pipe?
It means saying goodbye to waking up early to water your plants before heading to work, and no more rushing back home to keep them alive during particularly hot days.
How to find a broken pipe in a water system?
Allow the ground to dry up. Turn on the valve once the ground is dry. Check the ground above the irrigation lines for signs of wetness. Finding a broken pipe in your system involves the process of elimination. You’ll have to dig around a suspected leaking spot on the ground to find which of the pipes is broken.
Why is my sprinkler system leaking?
Once you are familiar with the locations of your irrigation lines, it’s easier to check if any issues you are having with your sprinkler system is due to a broken pipe. Leaks happen as a result of this, and signs of leaking are what you need to keep an eye out for.
What does it mean when your sprinkler system makes a noise?
You hear hissing, bubbling, or gurgling sounds – if you suspect a leak is present on your underground sprinkler system, literally keeping an ear to the ground may clue you in. Leaks on an in-ground sprinkler system can make noises.
How far away from the sprinkler head is the water coming out?
Even if you managed to narrow down where the water is coming out from, the actual source may be a couple of inches, or even feet, away from it. You should first determine if the leak is due to a broken pipe or an issue with the valve or sprinkler head.
How to tell if a pipe is broken in an irrigation system?
Leaks are the best clues for you to find a broken pipe in your irrigation system. Find a leak, and you’ll likely find a broken pipe.
How to tell if a sprinkler line is leaking?
Once you’ve identified where the leak is, mark the location so you can find it when the water is turned off.
How to find a leak in a sprinkler system?
After you turn on the sprinkler system, walk through the area where the sprinkler system is installed. Listen for running water and walk towards where you hear the sound to locate the leak in your sprinkler line .
Where is the break in the water line located?
The break or leak in the water line will be located between the last working sprinkler head and the first nonworking one.
How to stop water from leaking in a water line?
If you’ve found the signs of a leak and located the region where the line is leaking or broken, turn off the water so you can repair the line. Use the shut off valve in the control box to stop the flow of water through the system. Wait 1-2 minutes to allow the water to finish flowing through the system.
How to extend a plastic pipe?
Insert a slip coupling into the pipe. A slip coupling is a plastic pipe that is flexible and allows you to extend it to the length that you need it to be. Slide the end of the coupling into 1 end of the exposed pipe. Then, extend the coupling so it fits into the other end of the pipe.
What does a larger break in a system mean?
A larger break in the system could mean a costly repair.
Where to get a slip coupling for a pipe?
Bring the damaged section of pipe to the hardware store so you can get a slip coupling with a diameter that fits into it.

Step 1 – Constant Pressure vs. Zone Line
Step 2 – Find Broken Pipe
- If you happen to have a main line break, then you will need to make sure that you shut the water off completely. From there, you will need to get a hole dug into the ground with a shovel. Make sure to remove all of the soil and the sod that is in the area where the water was pooling up. You will then need to figure out what kind of pipe is broken.
Step 3 – Expose Pipe
- You will need to get the pipe completely exposed by removing all of the soil surrounding it. If the line break happens to be on a poly pipe, you will need to get about 2 feet of the length exposed. About 3 inches of soil will also need to be removed on either side of the exposed section. If it is a PVC pipe, then you will expose 2 feet in length and 6 inches on either side.
Step 3 – Inspect Damage
- Once you have the pipe exposed, you will need to look over it to figure out what made the line break in the first place. A lot of the time the causes include extremely cold weather, freezing or frost can easily bust a pipe. It could also be holes or cracks caused by aerators or other types of equipment. Deep growing roots or digging animals could also be a problem as well as poor insta…
Step 4 – New Pipe
- Once you are aware of the type of pipe it is and how much length you will need, you are ready to get your new poly pipe or PVC. Remember to get at least 2 new fittings as well as anything else that needs to be replaced like maybe a sprinkler head. Make sure that you get the correct size and fittings for the system that you already have.
Step 5 – Replace
- You will need to measure the area that is busted and mark it. Then use pipe cutters to cut the area that needs to be replaced. Use a pipe clamp on either side of the new fitting.