How To Fix a Leaking Evaporative (Swamp) Cooler
- Turn Off the Power. Before you begin, turn off the swam cooler and either unplug it or turn it off at the breaker box. ...
- Look at the Water Line. Check the water feed line. ...
- Inspect the Float Valve Inlet. ...
- Adjust the Float Arm. ...
- Check the Pads. ...
- Inspect the Drain Hole. ...
- Look for Scale Buildup. ...
- Inspect the Reservoir. ...
- Replace the Reservoir Liner. ...
Full Answer
How do you clean a swamp cooler?
Step 3: Clean the chassis and accessories
- Cleaning the Machine chassis: The chassis can be cleaned with a soft cloth or a brush.
- Cleaning the fan blade: use a soft cloth to wipe the fan blade. Be careful not to drop the dust into the duct pipe.
- Cleaning the water level sensor: a small wet cloth can be used to clean the dirt on the water leveler.
How do you install a swamp cooler?
Here are a few ways to make your swamp cooler colder:
- Open a window in the room for the cool air to circulate properly.
- Place an energy-efficient dehumidifier at the air intake region of the swamp cooler.
- Place plants like Boston fern, Peace Lily, Aloe, Cacti that absorb moisture easily in your room.
- Prime the cooling pads in the swamp cooler by getting them wet first.
How do you replace a swamp cooler motor?
- Remove the side panels on the swamp cooler.
- Remove the motor belt.
- Unplug the motor wiring.
- Remove the bolts.
- Remove the old motor.
- Install the new motor.
- Bolt the new motor into place.
- Attach the belt and tighten it.
How to install a car swamp cooler?
- Swamp cooler
- Measuring tape
- Level
- Hooks
- Chains
- 2 cinder blocks
Why is my swamp cooler not getting cold?
Probably the single most common reason your swamp cooler is not blowing cold air is that the circuit breaker has tripped or the fuse has blown. These are installed so as to avoid electrical damage to the unit, so it doesn't get fried in the case of an electrical overload.
How do you repair an evaporative cooler?
If there is a hole in the pan, you will need to use roofing cement or tar to patch the hole. After it dries, you can use the evaporative cooler spray to seal the rest of the pan. Once it has dried you need to apply another coat of sealant to the pan.
Why would a swamp cooler stop working?
The most common reason for swamp coolers to break down is that the evaporative pads become saturated with water or that scale and debris builds up on them. It's also possible that the internal belt will break or slip off, and in that case it will need to be replaced.
How do you reset a swamp cooler?
0:185:25Polishing a turd (Swamp cooler rebuild) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're gonna get this swamp cooler turned off and taken apart panels pulled off these panels GodMoreSo we're gonna get this swamp cooler turned off and taken apart panels pulled off these panels God they must wait 35 pounds each they're insanely plugged up with calcium.
How do you unclog a swamp cooler?
Brush out the inside of the swamp cooler. Use a stiff brush or broom to sweep the inside of the swamp cooler. After you brush the debris and dirt loose, use a small vacuum that can be used on wet and dry surfaces to vacuum up the dirt.
What are the parts of a swamp cooler?
The Parts of an Evaporative Cooler (Swamp Cooler)Motor.Shaft Bearings.Motor Pulley.Blower Pulley.V-Belt.Water Pump.Drain and Overflow Tube.Float Valve.More items...•
Why did my cooler suddenly stopped working?
Very often if your water cooler is not working, the problem can be traced to the power supply. So as a first step, check that it is properly plugged in at the wall and the mains power is turned on. If it is switched on but not dispensing water, the next step is to check your water supply.
What to do if cooler is not cooling?
0:001:06Air Cooler | Room Is Not Cooling Properly - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell this might happen if the water tank is empty or it is out of ice cubes all you have to do isMoreWell this might happen if the water tank is empty or it is out of ice cubes all you have to do is switch on the pump add adequate water in the tank through the water inlet using a mug or a drain pipe.
Why is my swamp cooler blowing out warm air?
When evaporative coolers blow hot air, this can be caused by numerous things. Sometimes it's merely caused by humid weather outside. Other times, it might simply be because you just have the “vent/fan” setting turned on, on your unit. You can get away with just turning the fan on when it's cooler outside.
Do coolers stop working?
Like most things in life, coolers aren't designed to last forever. Yes, even your expensive Yeti and Engel coolers will ultimately kick the bucket. Many people will run their coolers into the ground and keep using them until they fall apart.
Why won't my swamp cooler go on high?
Unplug the swamp cooler and adjust the float arm if the water isn't at the proper level. A swamp cooler only works effectively when the water level is high enough to keep the internal pads damp. If the pads start to dry out, the swamp cooler may not work on the high setting.
Why does my swamp cooler pump keep burning out?
Electrical problems lead to shorting of the components to the swamp cooler, thus potentially causing the pump or the motor to burn out. Such issues might result from faulty wires, sudden power surges, or bad electrical connections.
Why is my evaporative cooler leaking water?
The water may be dripping due to many reasons. Most often, it is due to improper storage of the cooling unit during the winter. Make sure that you store the unit properly. Before winterizing the evaporator cooler, you should drain the unit, remove the pads, and clean the tank.
Why is my evaporative cooler blowing warm air?
Check the pads—Many times a problem with the absorbent pads causes a swamp cooler to blow warm or hot air. Over time the pads lose their absorbency and don't hold enough water to make the evaporative process work efficiently.
Why is my evaporative air conditioner leaking water?
Dirty air filter – A dirty air filter will block the airflow over the evaporator cooler and this will make the evap coil too cold and result in it freezing over. Then it will melt and drip all the water into the pan which is too much for it to hold and it leaks.
Why is my portable evaporative cooler leaking?
If the pads on your swamp cooler are the wrong size or placed incorrectly, water can get through and drip onto your floor. Cracked reservoir: If water is dripping from the bottom of the swamp cooler, and the float valve isn't the culprit, you likely have a cracked reservoir.
Why do swamp coolers have mesh?
The mesh is secured along the inside of the side panels with screws. An unsteady mesh can cause the padding to protrude and cause severe splashing of water.
How to make a water cooler not overflow?
This, in turn, depends on the functioning of the float valve. Ensure that the float valve arm is properly positioned. Sometimes the float valve is deflected towards the edge of the water reserv oir. Tighten the nut securing the float valve with a wrench.
Why is my water cooler leaking?
Drain the remaining water from the cooler and repair the cracks. A few beads of an acrylic caulk can work efficiently in plugging the leakage. Another reason for water leaking from the bottom of the cooler can be a slack overflow pipe. Look to see if the pipe is properly positioned on to its drain hole.
How to tighten a compression nut?
If water is still dripping from the nut, you need to check the washer. Shut off the water supply. Disconnect the water line by loosening the compression nut. Inspect the inner surface of the compression nut and its washer.
Why is my swamp cooler blowing hot air?
This means that the problem likely has something to do with your water pump. Make sure you test it on the lowest setting possible, and see if it still blows hot air. If it does, continue with the steps below.
How to get water out of a catch pan?
First off, you will want to take the water out of the catch pan by dumping it, and then using a wet vacuum for the rest. Let it dry completely before moving onto the next step.
How do I replace a water pump belt?
Simply put the new belt in in the same way you removed the old belt. Make sure it is in properly and is snug before securing into place. After it is properly inserted, tighten the belt as well as the the mounts to hold it in place securely. So far you have taken care of any leaks, and replaced the belt. It's now time to look at your water pump.
How to cool a swamper?
Step 1: Replace the Blue Pads With Good Old Aspen. The blue sponge pads do not really absorb the water very well and do not cool well at all. So pitch them and replace them with the low tech, sustainable aspen pads. the aspen wood actually absorbes water in additon to creating a curtain of water which makes the swamper cool better. ...
How do swamp coolers work?
Swamp coolers work ok until it reaches 94 degrees. At that point, they stop cooling as well, because the pump can not get enough water on the pads to keep them wet. So by increasing the amount of water going to the pads by 50% the unit cools the house down faster, and the pads don't dry out. Ask Question.
How to stop swamper from turning on?
Go to the power switch and turn off the swamper. Then take some duct tape and tape it off. Then put a little sign that says not to turn on the power. (if someone turns on the fan motor while you are in there you will get hurt.) Also, you can unplug the fan motor up in the swamper for extra safety.
How to fix a water leak in a cooler?
Inspect the drain hole on the bottom of the cooler. If water is leaking out of the drain hole , then you most likely have a rather simple fix. Check to see if the reservoir's water level is above the top of the overflow pipe. If so, simply bend the float arm to adjust the water level. If not, check to see that the overflow pipe is screwed securely ...
What happens if your cooler leaks water?
If your cooler leaks water onto your roof, not only might you have to replace your cooler, but you may also have to replace your roof as well. Unless the cooler has been physically damaged, there are only six places that your cooler can be leaking from. We will run through these places one by one. Here are some simple ideas on how to diagnose ...
Why is my cooler leaking?
This common problem results in serious damage to the front screen cover of the cooler as rust and scale buildup slowly destroys it. This type of leak will usually be the result of one of three problems. 1) The top of the pad is so caked with scale that the water sprays off of it.
What to do if scale buildup is too much?
If it seems excessive you need to either clean the pad or replace it. If the level of scale buildup doesn't seem excessive, check to make sure that the plastic side wall of the reservoir assembly is seated properly, with the base inside the wall of the lower reservoir.
