How to Repair a Swamp Cooler Motor
- Catch Pan. First off, you will want to take the water out of the catch pan by dumping it, and then using a wet vacuum for the ...
- Locate and Seal. Now you have the chance to repair leaks by sealing them up. ...
- Inspect. You will want to inspect your belt for any cracks or splitting. ...
- Remove Old Belt. ...
- Insert New Belt. ...
- Hot Air. ...
- Turn Off. ...
- Test It. ...
Full Answer
How to fix a swamp cooler that won't cool?
Redesign the wind elbow or add silencer material 2. Increase the air outlet to the standard size. 3. Replace or adjust the fan blade. 4. Replace the motor. Note: The repair and maintenance of the swamp cooler is a professional job. Do not operate it without the guidance of a professional. Otherwise, it may cause personal injury!
How many volts does a swamp cooler use?
Swamp coolers have relatively small motors in their bodies. In swamp coolers, there are several types of motors with different capacities and power ranges. Most often, 1/3 to 3 horsepower motors are used. The other heavy motors require more than 220 volts, while these can efficiently be run on 115/120 volts.
How do you connect a swamp cooler motor to a circuit?
The swamp cooler motor is usually pre-fitted with four short wires, which must be connected to the control circuit for the cooler and the 120-volt circuit. All connections should be soldered and sealed with shrink-wrap insulation kits. It is most common to connect the colour-coded lines, as shown in the following steps.
Why is my swamp cooler leaking water?
If the pads on your cooler are worn, replace them for a new set before using the swamp cooler.You should then check the float valve. Water may be impeded from flowing into the reservoir by a broken valve, and this can cause leaks.
How do you disassemble a swamp cooler motor?
0:238:32Repair a Swamp Cooler that Shuts Down, Very Easy! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd see what's going on - two Phillips screws. So there's the clamps there you can see where theMoreAnd see what's going on - two Phillips screws. So there's the clamps there you can see where the Phillips screwed is took it out and the clamps just come right off the little hook.
How do I know if my swamp cooler motor is bad?
Signs Your Swamp Cooler Needs a New MotorAir Isn't Cool. If outdoor temperatures are in the 70s and low 80s and your swamp cooler isn't blowing cold air, something's wrong. ... System Doesn't Turn On. A swamp cooler that doesn't work at all could have a failed motor. ... Equipment Is in Bad Condition.
What causes swamp cooler motor to overheat?
Overheating occurs due to high belt tension, lack of lubrication or too high voltage. Inappropriately located or faulty thermostat may also result in continuous shutting of swamp cooler. The most critical component of an evaporative cooler that is most prone to failure is the motor.
Why is swamp cooler pump not working?
Your problem may be a lack of water, rather than a broken pump. Check to see that the pump is getting power. Some pumps plug directly into a standard electrical outlet, and some are wired inside of a box in the cooler. If the pump is not getting power, check the circuit breaker or the ground fault circuit interrupter.
How long do swamp coolers last?
But, while swamp coolers don't cost much to buy, they are a lot of work and money to maintain. Not only that, they are only warrantied to work for 5 years. Refrigerated air systems can last up to 20 years if properly maintained.
Why isn't my swamp cooler spinning?
The most common reason the evaporative cooler may not be giving a good air flow is because of the circuit breaker and fuse of the evaporative cooler, which are installed by the manufacturer to prevent damage to the unit. If there is a power surge, you can be sure that the unit will not be damaged.
How do you fix a overheating electric motor?
0:293:22Troubleshooting an Overheating Motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst check and make sure that nothing is blocking the ventilation holes. This may seem obvious. ButMoreFirst check and make sure that nothing is blocking the ventilation holes. This may seem obvious. But how often don't we overlook the obvious.
How do you fix a swamp cooler?
0:111:56DIY Swamp Cooler Maintenance and Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere is an adjustment screw but you usually will have to give the float arm a little bend to fine-MoreThere is an adjustment screw but you usually will have to give the float arm a little bend to fine-tune. It. Now place a water tablet into your pan.
Why does my swamp cooler pump keep burning out?
Electrical problems lead to shorting of the components to the swamp cooler, thus potentially causing the pump or the motor to burn out. Such issues might result from faulty wires, sudden power surges, or bad electrical connections.
What to do if pump of cooler is not working?
Water cooler troubleshooting Very often if your water cooler is not working, the problem can be traced to the power supply. So as a first step, check that it is properly plugged in at the wall and the mains power is turned on. If it is switched on but not dispensing water, the next step is to check your water supply.
How do you test a cooler pump?
The only way to accurately determine if your Liquid Cooling Pump is functioning, is by checking the Pump RPM. This will only be possible if the pump cable is connected directly to a fan header on the motherboard.
How do you clean a swamp cooler pump?
Clean the water reservoir at the bottom of the cooling unit at least once a month during summer to keep deposits at bay. When cleaning, you should turn off the cooling unit, then scrub it with a stiff brush soaked in water and vinegar mixture. After scrubbing, rinse the cooling unit with fresh water.
How do you test a swamp cooler?
Check the water level in the bottom tray. It should be about one inch below the top of the tray, and below the top of the overflow pipe. If the water level is too high or too low, adjust the float arm. Make sure your float valve is working properly.
Why did my cooler suddenly stop working?
Very often if your water cooler is not working, the problem can be traced to the power supply. So as a first step, check that it is properly plugged in at the wall and the mains power is turned on. If it is switched on but not dispensing water, the next step is to check your water supply.
Why does my swamp cooler pump keep burning out?
Electrical problems lead to shorting of the components to the swamp cooler, thus potentially causing the pump or the motor to burn out. Such issues might result from faulty wires, sudden power surges, or bad electrical connections.
Why is my swamp cooler not getting cold?
Probably the single most common reason your swamp cooler is not blowing cold air is that the circuit breaker has tripped or the fuse has blown. These are installed so as to avoid electrical damage to the unit, so it doesn't get fried in the case of an electrical overload.
What is swamp cooler?
The environmental protection swamp cooler is a kind of ventilation and prevention combination unit for dust clean, cooling, and deodorization purposes. Although there could be many reasons causing a problem, there are a number of general troubleshooting steps that you can follow to get the Swamp Cooler working again.
How to replace a fan on a spherical cylinder?
1. Adjust the phase#N#2. Check whether the motor is damaged, whether the fixing hoop and the fan seat are deformed#N#3. Replace the main magnet#N#4. Clean or replace the water curtain or dust net#N#5. Replace the fan#N#6. Replace the main board.
How to reset a power supply?
Restore power supply, check the power supply circuit#N#2. Replace the signal line or adjust the circuit#N#3. Replace the main control board#N#4. Close the air switch or replace the fuse#N#5. Replace the panel.
Is swamp cooler repair a professional job?
Note: The repair and maintenance of the swamp cooler is a professional job. Do not operate it without the guidance of a professional. Otherwise, it may cause personal injury!
Why do swamp coolers need to be repaired?
Another common need for swamp cooler repairs is caused by the fan breaking down. This may be caused by a number of factors. Remove the fan from the cooler, and examine the condition of the fan paddles. If they are damaged or corroded, discard the fan and start again. Look at the motor and belt which drives the fan.
How does a swamp cooler work?
The swamp cooler is a water-based device that cools the air by increasing the humidity. There are many complex parts to a swamp cooler, including the water reservoir, the air pumps, the electrical connections, and then fan. A lot of these items can become broken just by sitting in storage during the winter, so you will need to practice a few swamp cooler repair basics before you use it in the summer.
What to do if swamp cooler pads are worn?
If the pads on your cooler are worn, replace them for a new set before using the swamp cooler.You should then check the float valve. Water may be impeded from flowing into the reservoir by a broken valve, and this can cause leaks. Replace the valve is necessary.
How to winterize swamp cooler?
Water can sometimes be accidentally left in the reservoir, or it may not be sufficiently dry before it is packed away for the winter. Remove mold by using a combination of water, vinegar, and bicarbonate of soda, and scrub away at the inside of the machine. In the future, it is a good idea to learn how to properly winterize your swamp cooler, as this will prevent some repairs from being necessary in the summer.
How to clean mold off a swamp cooler?
Remove mold by using a combination of water, vinegar, and bicarbonate of soda, and scrub away at the inside of the machine. In the future, it is a good idea to learn how to properly winterize your swamp cooler, as this will prevent some repairs from being necessary in the summer.
What are the parts of a swamp cooler?
There are many complex parts to a swamp cooler, including the water reservoir, the air pumps, the electrical connections, and then fan. A lot of these items can become broken just by sitting in storage during the winter, so you will need to practice a few swamp cooler repair basics before you use it in the summer.
How to get swamp cooler out of retirement?
Once you get your swamp cooler out of retirement, you will need to perform a quick check of the machine. Plug it into a safe socket (which has a circuit breaker device installed), and then operate it for a full cycle.
How Do Swamp Coolers Work?
The fan then sucks the evaporated air from the mat and pushes that into your air.
How Are Swamp Coolers Maintained?
Just as with air conditioners, proper maintenance is an important aspect of swamp cooler ownership. You can really cut down on the longevity of your evaporative cooler by neglecting simple maintenance.
Why does my swamp cooler overheat?
Swamp coolers overheat and shut down for a variety of reasons. Poorly configured, lubricated, or wired components can lead to the interior of the swamp cooler overheating. Using the incorrect amount of voltage to run the swamp cooler can also cause overheating and permanent damage.
Why is my swamp cooler bogging down?
Given the simplicity of the swamp cooler’s operation, you can see why one component having trouble bogs the whole thing down. More often than not, it’s the motor that becomes problematic, with overheating likely being the issue.
How many shaft bearings are needed for swamp cooler?
Helping the motor inside your swamp cooler work correctly are two shaft bearings. Those shaft bearings have to move around a lot inside the swamp cooler, which is why they have to be lubricated.
How long does a swamp cooler last?
Assuming proper maintenance, your swamp cooler could last for well over 20 years. In this case, proper maintenance means conducting major cleaning and continually checking on the cooler even when it’s not in use.
What happens if the voltage in a cooler is too high?
If the amount of voltage used to run the cooler is too high, its internal components could get damaged. The wiring could start to fry and the motor will almost certainly overheat.
