Repairing Guides

how to repair a torn speaker cone

by Sadie Bahringer Published 2 years ago Updated 2 years ago
image

The best way to repair the paper speaker’s cone is to cover the cracked area with elastic glue and then to cover the glue with thin paper patches on both sides of the cone.

Part of a video titled How To Fix A Ripped Speaker - YouTube
2:57
6:01
So the first thing we do is we just need to give it a little but a more glue on here and get itMoreSo the first thing we do is we just need to give it a little but a more glue on here and get it roughly the size of the pitch. Sweet so now we'll take our first little patch.

Full Answer

What kind of glue to use to repair speaker cone?

Black Rubber Cement Speaker Repair Glue 1 oz. BottleBC-1 speaker repair glue is a specialized black rubber cement intended for spider to frame, surround to frame, and gasket to frame adhesion. Its fast setup and medium viscosity are ideal for attaching dust caps of almost any composition to cones of almost any composition. Also works great when attaching surrounds to poly cones. Solvent-based ...

How to properly clean speaker cones?

Clean off all of the small particles of cone material. Black particles from the old cone will still remain on the housing until you remove them. Using a chisel or sharp scraper, carefully remove all pieces of cone and spider remnant from the speaker housing. Scrape every square inch and use an air compressor periodically to remove any loose pieces.

How to replace a speaker cone?

How to Replace the Cone Woofer on a Subwoofer

  • Gently pry back the silicone/rubber trim ring that surrounds the woofer Please Note: There may be some adhesive that is keeping the ring stuck to the cabinet. ...
  • Once the trim ring is removed, begin removing the screws from the perimeter of the woofer using a 3mm hex key head
  • With the screws removed, the woofer should come free and pull out toward you

More items...

How to repair a cracked speaker cone?

Repairing paper speaker cone

  • Remove the speaker from its place. ...
  • Clean the speaker’s cone using a wet cloth. ...
  • Apply a thin layer of glue to the cracked area on the top side of the speaker using a soft paintbrush. ...
  • Cover with glue one side of the prepared patch. ...
  • Flip the speaker over and do the same on the bottom side of the speaker starting from the cone. ...

More items...

image

How do you repair a tear in a speaker?

0:201:17Speaker Repair; Torn Surround - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd went right into the speaker surround. So we get to repair that now I am using this LoctiteMoreAnd went right into the speaker surround. So we get to repair that now I am using this Loctite fabric glue. It seems to work pretty well I've heard some people using rubber cement.

How do you repair a hole in a speaker cone?

0:072:05Repairing a Speaker Cone - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis out and then using a paint brush just kind of repair it with the glue. And then let it sit toMoreThis out and then using a paint brush just kind of repair it with the glue. And then let it sit to cure. So I'm just going to mix the glue. Up. Just apply so I'm gonna reach in behind with my finger.

What kind of glue do you use to repair a speaker?

Permabond 737 is a toughened cyanoacrylate adhesive that is ideal for use in applications regarding the speaker cone, such as surround to cone, cone to spider, and dust cap to cone parts of the speaker.

Can you glue a speaker cone?

1:516:37Repairing a Speaker Cone Using Hot Glue - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay the beauty of using a hot glue gun as opposed to some of the other methods is hot glue actuallyMoreOkay the beauty of using a hot glue gun as opposed to some of the other methods is hot glue actually is very pliable once it cures. So it's it's flexible its pliable.

How do you fix a ripped sub cone?

3:4613:47CHEAP FOAM from Walmart | HOW TO Fix a Torn Speaker TutorialYouTubeStart of suggested clipEnd of suggested clipAnd just cut a little piece of this around right off and use it as a patch. With some e6000 like we'MoreAnd just cut a little piece of this around right off and use it as a patch. With some e6000 like we're using here or even some silicone.

Can a hole in a speaker be repaired?

Obtain material for repair. Most speaker cones are made from paper or a thin plastic. To fix the hole, an amount of similar type and density material, but slightly larger will be needed. If unable to find the thin plastic used in some speakers, paper may be used.

What glue can I use on speaker cone?

use flexible glue - such as rubbur or silicone. Hard glue such as cyanoacrilates(superglue) will crack or the cone/surround at the edge of the glue will fail...

Can you use rubber cement on speakers?

I purchased this adhesive to reattach the dust-caps of the mid/bass drivers of a pair of TEAC loudspeakers that had come loose with age/oxidation of the original adhesive. Worked very well; drivers back to normal. This "rubber cement" is easy to apply and is really "high tac", making it useful for other applications.

Can you repair a speaker with silicone?

0:031:08DIY Fix Blown Speaker with Silicone - YouTubeYouTubeStart of suggested clipEnd of suggested clipActually my silicone fix worked really well.MoreActually my silicone fix worked really well.

How do I fix my speaker Center?

1:092:08CNET How To - Fix a dented speaker cone - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou take a q-tip chop. Off the top of it Midway. So that it's nice and flat then apply a few dabs ofMoreYou take a q-tip chop. Off the top of it Midway. So that it's nice and flat then apply a few dabs of super glue to the tip. Let it soak in for a few seconds.

How do you make a homemade speaker cone?

1:0717:26Home Made Speaker Driver - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it sounds louder. So I'll glue the coil to a membrane or a cone now the voice coil and the coneMoreAnd it sounds louder. So I'll glue the coil to a membrane or a cone now the voice coil and the cone will vibrate together and the sound will be much louder. But this was a prototype.

What is Spider in speaker?

Spider. The Spider fits around the speaker voice coil and is attached to the speaker basket. It is one of the components (along with the cone) that help to keep the voice coil centered in the magnetic gap and affects excursion (movement).

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9