Repairing Guides

how to repair a touch lamp

by Norberto Senger Published 3 years ago Updated 2 years ago
image

How to Repair a Touch Lamp

  1. Troubleshoot the problem. Make sure it's not as simple as a bad bulb or a faulty electrical outlet. ...
  2. Unplug the touch lamp, and pry off the bottom with a butter knife. Check that all the wire connections are inside the lamp.
  3. Replace the touch sensor located at the base of the lamp. Purchase one at any electrical supply store or home improvement outlet, and follow the manufacturer's installation instructions.
  4. Check any fuses inside the lamp. Some newer touch lamps have soldered-on fuses. Replace any burnt fuses with fuses that carry the same rating.
  5. Install a new power control transistor, called a thyristor or TRIAC. You'll find this on the circuit board in the base of the lamp.

You can do it by following these steps.
  1. Troubleshoot the problem. ...
  2. Unplug the touch lamp, and pry off the bottom with a butter knife. ...
  3. Replace the touch sensor located at the base of the lamp. ...
  4. Check any fuses inside the lamp. ...
  5. Install a new power control transistor, called a thyristor or TRIAC.

How do I Fix my Touch lamp?

How do I fix my touch lamp? How to Repair a Touch Lamp Troubleshoot the problem. Unplug the touch lamp, and pry off the bottom with a butter knife. Replace the touch sensor located at the base of the lamp. Check any fuses inside the lamp. Install a new power control transistor, called a thyristor or TRIAC. Are touch lamps safe?

How to convert a touch lamp to a regular lamp?

You will also need some tools:

  • Drill
  • Multimeter
  • 3d printer (or project box)
  • Soldering iron

How to refurbish an old lamp?

Restoring an Old Lamp

  1. Things You Will Need. Spray Paint. ...
  2. The Old Lamp - Unplug & Remove the Bulb. Old lamp with bulb. ...
  3. Removing Rust. Rubbing surface with rough sponge. ...
  4. Priming and Painting. Scraping Paint Surface. ...
  5. Lubricating & Oiling. IMAGES: Lubricating all moving parts and joints. ...
  6. Wiring. Old 2 Pin Plug. ...
  7. Restoration Complete. Restored Lamp. ...
  8. Safety & Warning. ...

Can a touch lamp switch be repaired?

A touch lamp utilizes a sensor that lets you turn the lamp on or off with the touch of your hand. It can be more difficult to repair a touch lamp because you must disassemble it befor replacing any parts. You can do it by following these steps. Step 1

image

What causes a touch lamp to stop working?

Eventually, you may run into a problem with your touch lamp. If it's not turning on, it could be an electric problem, a damaged cord, a burnt out bulb or a worn out sensor. Touch lamp sensors do wear out after a period of use. You can replace the sensor yourself rather than purchasing a new touch lamp.

How do I fix my touch control lamp?

How to Troubleshoot a Touch LampInspect your touch lamp's lamp cord for damage. ... Unplug the touch lamp from the outlet. ... Plug the touch lamp into a working outlet. ... Check the bulb for a damaged filament. ... Unplug the touch lamp and remove the light bulb if it still doesn't work. ... Remove the light bulb and unplug the lamp.More items...

Does a touch lamp need a special bulb?

You do not need a special bulb for a touch lamp. You just bought a touch lamp, which you can turn on and off by touching the base of the lamp. You might wonder if your lamp requires a special bulb, but it doesn't. You can use any standard bulb for your touch lamp.

Can you repair a touch light?

How to Repair a Touch Lamp. A touch lamp utilizes a sensor that lets you turn the lamp on or off with the touch of your hand. It can be more difficult to repair a touch lamp because you must disassemble it befor replacing any parts.

How do you fix a lamp that won't turn on?

HOW TO FIX A LAMP THAT DOES NOT TURN ON: Be sure the lamp is plugged in, try a different power outlet, make sure the power outlet is on, try a different light bulb, check the circuit breaker, screw the bulb all the way in, wipe off the threads on the light bulb, turn the light switch to ON.

Can I use an LED bulb in a touch lamp?

Lighting consultant Terry McGowan said that if a touch lamp has a mechanical switch, it will work with any CFL or LED bulb. However, if the lamp has an electronic switch, you'll need to use a CFL or LED bulb that's specially marked as dimmable.

What activates a touch lamp?

A touch-sensitive lamp is one that is activated by human touch rather than a flip, push-button, or other mechanical switch. These lamps are popular as desk and nightstand lamps. They act on the principle of body capacitance.

Can I use a dimmable bulb in a touch lamp?

It's worth noting that touch-sensitive lamps that are dimmable require a dimmable bulb or LED equivalent. Factor this in when you're planning to buy a touch lamp and avoid the disappointment of setting up the lamp at home only to realise that you need to buy a bulb before you can use it.

How do touch lamps work?

How Touch Lamps Work. Touch lamps work because the human body functions as a link in the circuit. The body is warmer than the air, has resistance and has radio reception. As such, it's possible to control the brightness of a lamp just by touching it. Advertisement.

What does touch sensitive lamp mean?

Advertisement. Additionally, touch-sensitive lamps rely on the body's capacitance, which means its ability hold electrons. When you touch a lamp controlled this way, you are allowing the circuit more electrons. It is possible to purchase an apparatus that will convert a traditional lamp to a touch lamp. Typically, you can find these ...

What is a three way touch lamp?

Three-way touch lamps are a fun and convenient alternative to traditional switch lamps. Sometimes, the mechanism within touch lamps stops working. Because these lamps usually include a dimmer control switch, the easiest way to fix them is to troubleshoot that piece. It is also possible to use an external dimmer switch. Advertisement.

Where is the dimmer switch on a lamp?

Usually, you can find a control box containing the dimmer switch at the base of the lamp. These are available for purchase and replacement, but it's advisable to photograph the way its wires are connected to the lamp before you disconnect it. This way, when you purchase a new control box, you will be able to reattach the wires in ...

Can you use a dimmer bulb in a wall socket?

You can also use dimmer sockets that screw into the lamp's light bulb socket. Once you have screwed in the socket, you can add a light bulb. In addition, there are dimmer sockets that plug into the wall. Once you plug your lamp into these sockets, it will operate like a touch lamp. Advertisement.

How do you change a touch lamp to a regular lamp?

These lights usually have a switch located near the ceiling. This switch controls the light bulb. In order to change the color of the light, you simply turn the switch to another position. To change the brightness of the light, you can adjust the dimmer knob.

How do you remove a touch lamp sensor?

To do this, remove the old bulb from the socket. Then, take off the metal base plate. After removing the base plate, unscrew the screws holding the bulb in place. Finally, put the new bulb into the socket. Reattach the metal base plate and screw the lamp back together.

Do touch lamps wear out?

You can change the touch lamp to a normal lamp by removing the touch lamp sensor from the base plate. Then remove the bulb from the socket and insert the new bulb into the socket. Replace the touch lamp sensor back onto the base plate. What is the difference between a touch lamp and a regular lamp?

Do non-dimmable bulbs work in touch lamps?

No, you cannot use a non dimmable bulbs in a touch lamp. A touch lamp uses a dimmer circuit to control the brightness of the light. It does not allow you to choose between different colors.

Can you rewire a touch lamp?

Touch lamps are used in places where people cannot reach easily. Touch lamps are usually placed near the ceiling or wall. Touch lamps are very useful because they allow users to turn on/off lights using only their fingers. In addition, touch lamps are designed to save energy and reduce electricity bills. Touch lamps are available in many shapes and sizes. However, touch lamps are not dimmable. Non-dimmable bulbs do not work in touch lamps.

WORKING PRINCIPLE OF TOUCH LAMPS

The human body is made of water. Water act as a major conductor for electricity. These water molecules are a source of electrons and electric charge. Touch lamps utilize these electrons and electric charge to turn on. These touch lamps are easy to use. They are most commonly used as table lamps for office works or study purposes.

DEFAULTS IN TOUCH LAMPS

Loose connection of wires or fused problems can prevent the bulb from turning on. If your touch lamp is not working effectively then must check its thyristor. The thyristor is a diode which controls all the electrical signals. A thyristor is one of the main components used to turn on the lamp.

METHODS TO FIX A TOUCH LAMP

Touch lamps are difficult to repair because they are made up of a complex system. Several steps can be used to fix the problem. The first step is to identify the cause of the problem. Assure that the bulb is not fused.

Install a new transistor

Install a new transistor for power supply if needed. If the bulb of the lamp is fused replace it with a new bulb. Check out the circuit boards of the lamp. If the circuit of the lamp is destroyed then fix it properly.

What to do if your touch lamp is broken?

Inspect your touch lamp’s lamp cord for damage. Your pets may have chewed through the cord, or other cord damage could have occurred that could cause the lamp to fail. You'll need to replace the cord if it's damaged.

How to fix a touch lamp that won't turn on?

Plug the touch lamp into a working outlet. If the lamp fails to light, unplug the lamp and remove the light bulb.

How to connect a touch lamp to a black wire?

Use one of the original wire connectors to connect the black touch control wire to the lamp wire wrapped in black electrical tape. Use the remaining wire connector to connect the red or gray touch control wire to the lamp wire wrapped in red electrical tape. Replace the lamp base. Plug the touch lamp into an outlet.

How to replace touch control on a lamp?

Replace the touch control inside the lamp base if the touch lamp still fails to light. Unplug the lamp and remove the bottom from the lamp base to expose the touch control. Wrap a small piece of red electrical tape around the lamp wire connected to the touch control’s red or gray wire. Wrap a small piece of black electrical tape around ...

How to fix a lamp that won't come on?

If the lamp fails to come on, you'll need to check the socket wiring. Remove the light bulb and unplug the lamp. Unscrew the finial and lift the lamp shade off the lamp harp. Find the metal sleeves at the bottom of the harp on each side of the socket.

How to check if lamp wires are connected?

Check the lamp wires to ensure they connect to the two terminal screws on the socket. Loosen the terminal screws, wrap the lamp wires around the terminals and tighten the screws if the wires were loose or disconnected.

How to remove a lamp harp?

Remove the light bulb and unplug the lamp. Unscrew the finial and lift the lamp shade off the lamp harp.

How to reset touch lamp?

Resetting the touch lamp requires replacing the touch-control box. Remove the finial holding the shade onto your touch lamp. Take off the lampshade to access the lamp harp. Squeeze the sides of the harp toward each other to release it from the harp saddle beneath the socket. Move the touch lamp to a work surface.

How to remove touch lamp base?

Move the touch lamp to a work surface. Remove the bottom from the lamp base. The bottom may be connected to the base with screws. Alternatively, it may pull off the base like you pull the lid off a butter container.

How to connect a touch control box to a lamp?

Remove the tape. Connect the red or gray wire from the touch-control box to the taped lamp wire that threads through the body of the touch lamp. Twist another one of the wire connectors onto these wires to hold them together.

How to hold two lamp wires together?

Twist the remaining wire connector onto the two remaining lamp wires and the white touch-control wire to hold them together.

What is the red wire on a lamp?

The red or gray wire connects to one of the lamp wires that threads through the lamp body and connects to the socket. Untwist the connectors that hold the lamp wires to the touch-control wires. Gently pull the wires apart. Trace the yellow wire from the touch control to the ring terminal attached to the threaded nipple connected to the body ...

Why does my touch lamp stay on and off?

An additional wire connects to the metal on the lamp. It is this wire that gives the lamp the ability to turn the light on and off when you touch any metal on the lamp. The control box can be damaged by minor power surges. When this happens, the touch lamp will remain in the “On” or “Off” position.

How many wires are in a touch control box?

The touch-control box has four wires connected to it. They are either black, red, white and yellow, or they are black, gray, white and yellow, depending on the manufacturer. Wrap a piece of tape around the lamp wire that connects to the black wire from the touch control.

image

What Is A Touch Lamp?

Image
A touch lamp is a lamp that turns on and off by touching it with your fingertips. A simple touch is enough. This lamp, therefore, has no switch on its cord. But how is this possible? It’s not magic, and rest assured it’s absolutely safe. These lamps comply with European standards for safety and insulation. The operation is simpl…
See more on lamppoint.com

Why Use A Touch Lamp?

  • A touch lamp can be used in many cases. Designers are using this solution more and more because it has many advantages, suddenly this type of light is no longer only used as a bedside lamp, even if it is still the first use.
See more on lamppoint.com

How to Fix A Touch Lamp

  • Touch dimmers are operated by your body. Your body acts as an antenna, or the conductor, and touching any part of the metal on the lamp — coupled with the 60 Hz circuit — causes the lamp to turn on or off or dim. The Convenience A tactile operating light makes it a good choice as a reading bedside lamp — Easy Off, Easy On. Try fixing your touch lamp if it is no longer working ra…
See more on lamppoint.com

Instructions

  1. Unplug the lamp from the wall outlet.
  2. Remove the bottom of your lamp. Use a flathead screwdriver to pry off the bottom of the lamp, exposing the wiring and touching dimmer.
  3. Remove the touch dimmer control from your lamp. Remove the nuts that connect the touch dimmer control to your lamp by untwisting them. If your dimmer switch will be wired — conne…
  1. Unplug the lamp from the wall outlet.
  2. Remove the bottom of your lamp. Use a flathead screwdriver to pry off the bottom of the lamp, exposing the wiring and touching dimmer.
  3. Remove the touch dimmer control from your lamp. Remove the nuts that connect the touch dimmer control to your lamp by untwisting them. If your dimmer switch will be wired — connected without wire n...
  4. Place the yellow wire of the new dimmer button on the lamp. The yellow wire has a ring attached to the end and slides over the threaded fitting at the base of the lamp. Locate the nipple by locatin...

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9