How to Fix a Leaking Urinal Flush Valve
- Turn Off the Water Supply Remove the chrome cap from the shut-off valve under the urinal. Using a flat-head...
- Remove the Flush Head Cap Use channel lock pliers to remove the flushometer head bolt. Next, remove the flush head...
- Replace the Diaphragm
Full Answer
How to fix a leaking urinal flush valve?
Follow these three steps for fixing a leaking urinal flush valve. 1. Turn Off the Water Supply Remove the chrome cap from the shut-off valve under the urinal. Using a flat-head screwdriver, turn the exposed valve screw counter-clockwise. This shuts down the urinal water supply. 2. Remove the Flush Head Cap
How do you remove a flushometer from a urinal?
Turn Off the Water Supply Remove the chrome cap from the shut-off valve under the urinal. Using a flat-head screwdriver, turn the exposed valve screw counter-clockwise. This shuts down the urinal water supply. 2. Remove the Flush Head Cap Use channel lock pliers to remove the flushometer head bolt.
How does a urinal flush work?
The main water line is cold water feed only and attaches to a flush handle that releases the water into the bowl. The flush handle is operated on a spring valve that allows a preset amount of water into the urinal, and the liquid uses gravity to flush the waste into the sewer drain. Here are some common issues along with likely solutions.
How to replace a toilet flush valve?
Take a look at the flapper or toilet flush valve located at the bottom of the tank. You will see that the flush valve is made out of a piece of rubber and hinges upwards to open. Undo the valve by unclipping the ears which hold it in place. Unclip the strap connecting the handle to the flush valve so that the toilet flush valve can be removed.

How do you rebuild a Sloan urinal flush valve?
1:452:44Sloan Valve Troubleshooting - Sloan Valve Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe new handle kit just drops into the handle. And then we're going to screw it tight. And then we'MoreThe new handle kit just drops into the handle. And then we're going to screw it tight. And then we're going to put it right back into the main body of the valve.
How do you fix a urinal that won't stop running?
When your urinal won't stop running, it could be because of a malfunctioning or contaminated diaphragm, located toward the top of the urinal. You can fix this yourself in many cases. You'll want to turn off the main water line if you can (in case it's a more serious problem).
How do you replace a urinal valve?
3:054:16Sloan Regal Flushometer | Diaphragm | Repair and Replace - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst remove the relief valve. Next unscrew the guide assembly. And discard the old diaphragm. PlaceMoreFirst remove the relief valve. Next unscrew the guide assembly. And discard the old diaphragm. Place the new diaphragm over the guide. The side marked this side down should not be visible.
How does urinal flush valve work?
Hydraulic Valve Flushing – A hydraulic valve flushing system is installed in line with the water supply inlet pipe into the cistern. The valve works by sensing a temporary drop in pressure in the water supply. When this pressure drop occurs, the valve will release water into the cistern.
Where is the water shutoff on a urinal?
Locate the shutoff valve attached to the pipe behind your toilet. The shutoff valve is a football-shaped valve connected to a pipe or hose attached to the bottom of the tank behind your toilet. The other end of this pipe should go into the wall.
What is a Sloan valve?
Sloan Valve Company is a privately owned American company specializing in plumbing valves and fixtures.
What causes a Sloan flush valve to keep running?
Flushometer Continuously Runs/ Valve Will Not Shut Off This occurs when a control stop does not open all the way when the unit is flushed, which then causes the water pressure to not be high enough for the diaphragm to function properly and reset. This causes water to continuously run into the unit.
What causes a Sloan flush valve to keep running?
2:073:25Sloan Regal Flushometer | Installation | Repair and Replace - YouTubeYouTubeStart of suggested clipEnd of suggested clipSet the flush Elmander body on the flush pipe and hand tighten the tailpiece coupling and hexMoreSet the flush Elmander body on the flush pipe and hand tighten the tailpiece coupling and hex coupling. Now use a smooth draw wrench to secure each connection.Sloan Regal Flushometer | Installation | Repair and Replace - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you install a urinal flush valve?
How do you stop a Sloan flushmate from running?
When you push the flush handle, it activates a relief valve that tilts the diaphragm or piston just enough to allow water to flow from the upper chamber to the lower one, and that allows pressurized water to displace the diaphragm or piston, and the pressurized water flows into the toilet bowl.How Sloan Flush Valves Work | Hunkerhttps://www.hunker.com › how-sloan-flush-valves-workhttps://www.hunker.com › how-sloan-flush-valves-workSearch for: How does a manual flush valve work?
How do you shut off a Sloan Valve?
DESCRIPTION: The flushing valve, also called exchange valve is used to bleed the hot oil to- ward a cooler in the hydrostatic transmission. As the cooled oil continuously regulates the hydraulic circuit temperature, the flushing valve operation in- creases the fluid quality, thus the life span of the transmission.FLUSHING-VALVEhttp://www.saihydraulics.com › Systemhttp://www.saihydraulics.com › SystemSearch for: How does a hydraulic flushing valve work?
What causes a urinal to overflow?
Flushometer Continuously Runs/ Valve Will Not Shut Off This occurs when a control stop does not open all the way when the unit is flushed, which then causes the water pressure to not be high enough for the diaphragm to function properly and reset. This causes water to continuously run into the unit.
What is the Sloan valve on a urinal?
This part of a urinal flushometer is also called the Sloan valve. Replacing it usually stops a urinal from leaking when it’s flushed. Follow these three steps for fixing a leaking urinal flush valve. 1.
How to break up a clogged urinal?
You can use a regular plumber’s snake, but you’ll get better results with an auger designed for urinals. Remove the drain mat and cover, and then insert the auger cable down the drain opening. Crank the auger handle, pushing its head through the drain line. Slowly reel it back, and repeat as needed to break up the clog.
What Causes a Urinal to Overflow?
When a urinal starts draining slowly, an overflow can’t be far behind. Fixture components aren’t complicated, so that makes it easier to identify the best repair options. Most urinal overflows are caused by one of these two problems.
Why does my toilet need a flushometer?
Toilets rely on gravity to complete a flush, but a flushometer use s in-house water pressure to complete a flush cycle. When a urinal keeps running or leaks after a flush, it’s time to replace the urinal flush valve and diaphragm inside the flushometer. These parts can fail due to age or constantly fluctuating water volume and pressure.
Why do urinals overflow?
Clogged Drain Lines – Urinal drain screens and mats keep large items from falling down into the pipe, but small debris can bypass both and accumulate down in the p-trap. Sediment Buildup – Over time, sediment deposits build up in urinal drains.
How to remove flushometer head bolt?
Use channel lock pliers to remove the flushometer head bolt. Next, remove the flush head cap so that you have access to the diaphragm inside. Water will probably spill out around the open head cap.
What is the black disk in a flush head?
The exposed black disk in the flush head is the diaphragm. Remove it, and replace it with a new diaphragm. Secure the flush head cap back in place, and wipe down wet surfaces. Flush the urinal to confirm that parts are working properly.
Where is the flush valve seat?
Flush valve seat: The hole at the bottom of the tank.
What does the flush lever do?
When the flush lever is pulled, it lifts the flapper, allowing the water in the tank to flush down into the toilet bowl. The cylindrical float or ball float then raises with the water level, shutting off the water supply once the correct level is reached.
How to remove a ball float from a tank?
Follow steps one and two above, then do the following: Remove the ball float using a plastic snap. Unscrew the nut or snap the rod out of the valve. Put the flush valve through the hole in the bottom of the tank. Hold the flush valve in place with a nylon nut. The nut should be snug, but be careful not to overtighten it.
Why does my toilet tank leak?
When there is a leak from your toilet tank, it could be any of the following reasons: The flush valve is damaged. The flush valve doesn't seal tightly because of built-up mineral deposits. The flapper is worn out. To confirm a leak, simply turn off the tank's water supply, mark the water level, and wait about 30 minutes.
Why does my toilet run constantly?
If you hear your toilet running constantly, chances are you have a leaking flush valve. This is the most common problem in a toilet tank setup and is fairly easy to fix. Fixing it yourself can save a lot of money in water usage, and you won't have to hire a professional plumber.
How to fix a worn out flapper?
This is a super simple fix. Remove the old or worn out flapper from the overflow tube and detach the chain from the handle arm. Attach the new flapper to the overflow tube and hook the chain back on the handle arm.
How to check if a water tank is leaking?
To confirm a leak, simply turn off the tank's water supply, mark the water level, and wait about 30 minutes. Iif the water level has dropped, you have a leaking valve.
How to undo a toilet flush valve?
Undo the valve by unclipping the ears which hold it in place. Unclip the strap connecting the handle to the flush valve so that the toilet flush valve can be removed. If this is damaged then it cannot be repaired and will need to be discarded.
What is a flush valve made of?
Most of these flush valves are made from rubber although some of them will be made from much higher quality and more durable materials which will help them to last longer even in chlorinated water. When the parts get older they can become brittle and this will result in them cracking or becoming damaged.
How to flush a toilet that has shut off?
Press the toilet handle to flush the toilet so that the water drains out, because you have shut off the water the tank will not be able to fill up again. Take a look at the flapper or toilet flush valve located at the bottom of the tank. You will see that the flush valve is made out of a piece of rubber and hinges upwards to open.
How to stop a toilet from running out of water?
Switch the water supply on to the toilet and allow the toilet to fill up again. Check for any signs of leaks, if there are leaks then check that the flush valve is seated correctly and is blocking the hole where the water runs out. Check that the chain isn't too tight against the valve as this will prevent the valve from closing properly.
Do you have to shut off the water before using a toilet?
Before you start work on your toilet you should shut the water off, if you have a wall valve located close to your toilet then you can use this . Otherwise you will need to use the master water valve which is normally located outside of your home.
Can you fix a leaky toilet valve?
Anyone who is suffering from a leaky toilet will find this a very irritating and frustrating problem, fixing a toilet flush valve is actually one of the easiest things that any home owner can actually do. This will also prevent you from wasting a lot of water because otherwise this water will be flushed down the drain.
What to do if a flushometer valve sticks and flushes continuously?
If a flushometer valve sticks and flushes continuously - or own't turn off on its own, Check first for dirt in the bypass orifice and clean it; Check for dirt in the valve seat or falve sealing area ; if cleaning doesn't fix this problem replace the valve parts as they're probably worn-out.
What goes wrong with flushometer valves?
What goes wrong with flushometer valves and their installations: troubleshooting inadequate flush water, too much flush water, noisy or leaky flushometer valves. We also introduce and recommend use of waterless urinals.
Why does my flushometer make a noise?
Damaged internal parts: inside cover has cracked; a damaged flushometer internal cover or a flushometer diaphragm that has been installed upside down can also cause chattering noises during flushing of the fixture; use a repair parts kit
What size water piping is needed for a flushometer?
The requirement for this flowing water pressure and volume for satisfactory flushometer valve operation and toilet or urinal flushing explains our earlier comments about the practice of supplying flushometer-operated toilets and urinals with 1 1/4" water piping.
Why is the flushometer valve not properly adjusted?
at WATER CONSERVATION MEASURES, particularly because they normally operate at high water pressures and send a significant water volume into the toilet, a flushometer valve that is not properly adjusted or that a flushometer valve that allows a toilet to run constantly can waste an enormous volume of water.
Why won't my flushometer stop?
FLUSHOMETER VALVE WON'T STOP. no flush water, too little flush water because flush time is too short, and too little flush water for other reasons, problems with over-flushing volume or time, and other flushometer problems such as noises or leaks.
How high should a flushometer be above a plumbing fixture?
For proper flushometer and plumbing fixture operation, the flushometer vacuum breaker must be a minimum of six inches (6") above the highest part of the plumbing fixture that it serves.
