If it's a Westminster only unit, UP is off and DOWN is chime. However, only if there is a switch. When the clock selector switch is on chime and still does not work, the next thing to check is a jam in the roll pin. To correct this pull all the chime side hammers back all at once and then let go.
Full Answer
How to set and adjust Westminster chime clocks?
How do I get my clock to chime correctly?
- When your mantel clock chimes, count the number of times it chimes.
- Move the hour hand to the hour indicated by the hourly chime (count the number of gongs at the hour).
- Reset the time using the minute hand to the correct hour and the chime should adjust along with the clock hands as well.
How to set a quartz Westminster chime regulator wall clock?
Instructions for Hermle Quartz Wall and Mantel Clocks
- Wall Clock Models. Unlock the pendulum holder from its shipping position by pushing it to the right with your thumb or finger.
- Batteries. Use Only Alkaline Duracell C Batteries! ...
- Time Setting. ...
- Melody Switch
- Night shut-off and night reduction. ...
- Volume control. ...
- Chime selector. ...
- Mounting wall clock models. ...
- Regulation. ...
- Instructions for clock with moon phase dial. ...
How to set up a chiming clock?
Setting the Time
- Open the hinged glass cover of the clock’s face to access the clock’s hands.
- Set the time by moving the big hand forward, pausing at the 11 o’clock position.
- Listen for the subtle sound of a spring unwinding before moving further.
- Move the big hand to the 12 o’clock position.
How to adjust chime clocks?
How to Adjust Chime Clocks. Check the position of the minute hand of the clock when the top-of-the-hour strike occurs. Open the access panel door to the pendulum and bring it to a stop. Remove the minute hand retaining nut by turning it counterclockwise. Remove the minute hand from its arbor.
How do you fix a chime clock?
0:313:51How to Fix Clock that Doesn't Chime on the Correct Minute - YouTubeYouTubeStart of suggested clipEnd of suggested clipSort of let the hand you know sort of sway back and forth and stop in the middle and you tighten itMoreSort of let the hand you know sort of sway back and forth and stop in the middle and you tighten it up and run it up to the top of the hour and it should hit on the dot.
How do I get my Westminster chime clock to work?
Set the minute hand first to the correct time and the hour hand should follow behind to the correct hour. If you have a knob for the hands, turn that clockwise or counterclockwise to get to the correct time. The chiming should begin in sync at the next full hour.
How do you fix an overwound chime clock?
Fixing An Overwound ClockClean The Clock. Sometimes cleaning your clock will get it working again. ... Lubricate The Mechanism. Like cars, all mechanical clocks need regular oiling. ... Replace The Springs. ... Find A Professional.
Why has my clock stopped chiming?
If your clock has stopped chiming after 5 years, or has stopped chiming correctly, chances are the problem is a lack of, or improper, maintenance. Most manufacturers of clocks recommend 'oiling' a clock every year.
How do I reset my Westminster Chimes?
Simply count the chimes at a convenient time , say 10 then stop the clock immediately. Then in your own time, loosen the hands and move them to the 10 o'clock position, now re-tighten them.
What are the 3 holes on a wind up clock?
In clocks with more than one keyhole, the left-most hole usually controls the hourly chime, and in clocks with three keyholes, the center keyhole is typically for the quarter-hour chime, although again this can vary from model to model.
How do I free up my overwound clock?
Turn the key slowly and just a half turn at a time. Wind it up until it stops. Do not try to force it to wind any further. Even though it is impossible to over-wind your clock, it is also not necessary to wind it until the last possible click of the ratchet.
How do you tell if a clock is overwound?
Identifying an overwound clock If your clock does not have a weight inside it, you will likely find that the pendulum is warped and bent, possibly out of shape or worn.
How do you release the spring on an overwound clock?
2:595:01005 Clock Mainspring - How to let down the power... Safely! - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the mainspring let down tool onto the square of the barrel Arbor. This is a good opportunityMorePlace the mainspring let down tool onto the square of the barrel Arbor. This is a good opportunity to see how strong the spring is. So give the clock a little bit of a wind.
What is an overwound clock?
When the condition of a clock is described as "overwound," there is always another underlying cause for why the clock will not run. The clock ends up fully wound because winding is the first thing we try when a clock has stopped. It is difficult to determine the cause without inspecting the movement.
What kind of oil do you use on a clock?
Synthetic clock oil is not cheap because it is specifically formulated for the metals used in clocks. Brass and steel are used in clocks because when properly lubricated with the right oil it forms a perfect bearing. Brass is a soft metal which is why you won't find it in car engines.
How do you fix the hour chimes on a grandfather clock?
0:000:30Hour Strike Adjustment.mpg - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut it just struck three take the hour hand and move it to three then take your minute hand and goMoreBut it just struck three take the hour hand and move it to three then take your minute hand and go counterclockwise.
How to make a clock chime all day?
If you want the clock to chime all day, leave it in the sun position. If you prefer the chime to only sound while you are awake, you can set it to the no moon position, and it will not chime for the eight hours you choose it to be silent.
How to set the clock to the correct time?
To set the clock to the correct time, carefully turn the hands in a specific order. Set the minute hand first to the correct time and the hour hand should follow behind to the correct hour. If you have a knob for the hands, turn that clockwise or counterclockwise to get to the correct time.
How long does a German clock chime?
Please note that post WW2 German mechanical clocks are designed so that if turning the hands fast or stop the clock for a long while it may not chime for up to 3/4 of an hour. This is because the clock is looking for the top of the hour so it does not lose its place as to when to chime.
Why does my clock not chime?
If the clock does not chime it will not strike, so therefore the clock remains silent. This being a mechanical clock, it has no sensors to determine on its own what is night or day. Solution is to go around 12 hours with the clock hands.
What does ANSO mean on a clock?
Higher end mechanical clock movements sometimes include an ANSO feature. This stands for Automatic night shut off, and the intention is to have the clock be silent automatically from 10pm to 7am (usually). It is possible that it thinks it's night when it's really day, and therefore will not chime.
What is the silent switch on a clock?
Silent switch and roll pin. There may be a switch at the 3 o'clock and this switch turns the chimes on or off. If the clock is a triple chime movement, meaning it has three songs, it will have the song selection and also silent on this switch.
What is a grandfather clock chime?
Grandfather Clock Chime Issues. When a grandfather clock has issues with the chime functioning these are some basic corrections. The chime is the song that plays every 15 minutes and not to be confused with the strike. The strike is what calls out the hours after it is done with the chime song.
Why does a clock stop?
Resistance is what makes a clock stop because there is not enough weight to drive through whatever is rubbing. So if the chain or cable is rubbing something it's the same as not having the right amount of weight on the clock.
How to do a minute hand in chess?
Go forward with the minute hand with fingers while going slow past the quarters. A faint click can be heard and at that point pause and see if it starts chiming. If it does not chime go forward to the next and the next quarter. If the minute hand goes all the way around for an hour with no chime, continue to the next section.
Does a hammer train have a set screw?
It has a set screw but loosening it is usually not necessary. Anyhow, while turning this gear and at the same time not letting the gear train run, it will turn around and move the hammers until the hammers strike each one time right down in a row, representing the end of the first quarter.
Does Westminster clock sound like Westminster?
The Westminster mechanical clock does not sound like Westminster when it plays? This would require these Mechanical Chime Sequence Resetting Instructions. There is a cam with humps that graduate on the top right of the front plate of the movement. There are 4 lower portions with a small hump and the next one is bigger and so on.
