How to Repair Air Nailers & Staplers
- Step 1. Size an Allen wrench to the four mounting bolts holding the square grill to the back of your nailer.
- Step 2. Use a utility knife blade to pry the square vented cover from the tool and remove it to expose the plunger...
- Step 3. Spray an aerosol cleaning agent, such as a tool or parts cleaner, up into the chamber of the nailer.
Full Answer
How to use a staple gun properly?
Open the staple gun and skim the hammer by pressing down the stapler’s head The hammer should slide downward freely without any impediments Dislodge any obstructions using a flat head screwdriver De-grease and eliminate all gunk, grease, and dirt using the WD-40 or white vinegar
How do you remove a Stapler from a gun?
First, slide out the pusher rod. There will usually be a little tab at the end of the stapler that you must push down a little to clear the latching notch. Some manual staple guns have knobs. The pusher rod should slide right out. Next, remove the magazine.
How do I repair an air nailer or stapler?
The basic repair procedure is the same for almost all air nailers and staplers. Size an Allen wrench to the four mounting bolts holding the square grill to the back of your nailer. This is located at the top and rear of the tool at the opposite end of the barrel, and typically has a louvered, or ported, vent cover to allow air to escape.
How do you fix a jammed staple or nail gun?
Remove unused staples or nail strips so they aren’t staged for the next trigger pull. It would be unfortunate if your nail gun came back to life just in time to impale your leg. You should already be wearing eye protection, but if not, be sure to put on protective goggles before you attempt a fix for a jammed staple or nail gun.
Why is my staple gun not working?
Solutions for Jamming Slide out your gun's pusher rod (the bar that extends along the magazine of your tool.) Unscrew the bottom attachment of the magazine and remove it from your gun. Check for stray staples and other blockages. Clear the jammed staples using needle-nose pliers.
How do you fix an air staple gun?
1:3014:45Fix a Air Stapler Gun - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull it up take it out with one side just don't lose it then this comes out it's just hooked in theMorePull it up take it out with one side just don't lose it then this comes out it's just hooked in the body there kid do some of it.
How do you fix a stapler that won't staple?
Paper Clips A paper clip is the perfect size for picking at a jammed stapler. The method is the same as above, using the loop of the paperclip to try to loosen the jammed staple up so it falls out of the magazine. You can also try to pick out the jammed staple with the point of the paperclip, gliding it out.
How do I get my staple gun to work?
0:233:37How to Operate a Staple Gun - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst pull the back pin out. And you have two parts you take your staples load. Them in staple downMoreFirst pull the back pin out. And you have two parts you take your staples load. Them in staple down point down otherwise it won't work. So pretty simple it's loaded.
Why is my pneumatic stapler not working?
Jams are the most common cause of a nailer not firing. Thankfully, they are often easy to clear. For safety, first disconnect the tool from the air supply, retract the feeder mechanism, and remove any excess fasteners from the magazine. From there, clearing the jam depends on what type of nailer you have.
How do you put a staple gun back together?
0:482:05How to Breakdown and Clear Jammed Staples Arrow T50YouTubeStart of suggested clipEnd of suggested clipAnd you're gonna put it right through. And you'll take your nut. And put it back on and then do theMoreAnd you're gonna put it right through. And you'll take your nut. And put it back on and then do the same thing you'll just take your pliers. And then tighten it up.
How do you fix a broken stapler spring?
0:221:28Swingline 545 Stapler - spring replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipBack this little thin piece of metal up top I'll release this second hook one end of your spring toMoreBack this little thin piece of metal up top I'll release this second hook one end of your spring to this hook at the base. Then you're going to want to thread the other end. Through these two holes.
How do you fix a one touch stapler?
When a Staples One-Touch Stapler jams, it's usually because you have tried to insert the staples into the pull-out metal slider instead of into the body of the stapler. Turn the stapler upside down, tip out the staples and try again. If a staple is stuck in the stapler head, use a pair of tweezers to tease it out.
What is the screw for on a staple gun?
The pressure screw (C) may be adjusted so that it will apply the appropriate force to the staple, or nail, depending upon the material being stapled. Note: The softer the material, the less force will be required to drive in the staple or nail. Excessive force may damage the material being stapled.
How does a pneumatic staple gun work?
Pneumatic staple guns use compressed air to provide the force that drives a staple into wood, concrete, roofing materials, or plastic. They are more powerful than electric staple guns. The compressed air comes from a hose attached to an air compressor, or in some cases, from a canister that attaches to the tool.Pneumatic Staple Guns vs. Electric Staple Gunshttps://stapleheadquarters.com › pneumatic-staple-guns-vs...https://stapleheadquarters.com › pneumatic-staple-guns-vs...Search for: How does a pneumatic staple gun work?
How does a manual staple gun work?
Manual staple guns fire when you squeeze a trigger, and you control the time between firing one staple and the next. They don't have cords or batteries and are smaller and easier to maneuver than electric staple guns. Squeezing the trigger on a manual staple gun repeatedly can be hard on the hands.Electric vs. Manual Staple Guns: Which Is Better?https://stapleheadquarters.com › electric-vs-manual-staple-...https://stapleheadquarters.com › electric-vs-manual-staple-...Search for: How does a manual staple gun work?
Why wont the staples come out of my staple gun?
The staples that aren't jammed should fall out. Finally, use needle-nose pliers or a small flathead screwdriver to pull or pry out any jammed staples. They'll most likely be stuck at the front of the staple gun unless you are using the wrong-sized staples.Common Staple Gun Problems and How to Fix Themhttps://stapleheadquarters.com › common-staple-gun-prob...https://stapleheadquarters.com › common-staple-gun-prob...Search for: Why wont the staples come out of my staple gun?
How do you fix a stapler spring?
0:091:28Swingline 545 Stapler - spring replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipBack this little thin piece of metal up top I'll release this second hook one end of your spring toMoreBack this little thin piece of metal up top I'll release this second hook one end of your spring to this hook at the base. Then you're going to want to thread the other end. Through these two holes.
How do you oil an air stapler?
0:331:30Best Way To Oil Your Nail Gun or Air Tool - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll the tools you want to oil in the inlet. Where your fitting is the amount of oil depends on theMoreAll the tools you want to oil in the inlet. Where your fitting is the amount of oil depends on the tool some tools take just a couple drops like your micro Pender's your Brad nailers.
Why is my Powershot Stapler not working?
0:001:02How To Remove Jammed Staples from PowerShot 5700 Staple GunYouTubeStart of suggested clipEnd of suggested clipSo you can slide out the magazine. Next use a pliers or a flathead screwdriver to clear the chamber.MoreSo you can slide out the magazine. Next use a pliers or a flathead screwdriver to clear the chamber. And then reassemble your powershot staple.
What is the screw for on a staple gun?
The pressure screw (C) may be adjusted so that it will apply the appropriate force to the staple, or nail, depending upon the material being stapled. Note: The softer the material, the less force will be required to drive in the staple or nail. Excessive force may damage the material being stapled.
How to use air tool oil on a nailer?
Apply three drops of air tool oil into the inlet fitting, or air nozzle, on the bottom of the nailer, directly below the vent cover. Reattach the air hose, and fill the magazine with fasteners. It is now ready to use.
How to replace a plunger cylinder?
Apply air tool oil to the O rings with a cotton swab to keep them pliable and aid in the airtight seal, as well as providing lubrication for the plunger. Press the cylinder back into place, aligning any grooves or notches with the opening of the tool case, to ensure proper positioning.
How long do air nailers last?
A wellbuilt nailer, or nail gun, as they are sometimes called, can last for decades with proper maintenance. Provided the case of the tool remains intact and is not severely bent, most issues can be solved by cleaning ...
How to clean a nailer with a swab?
Spray an aerosol cleaning agent, such as a tool or parts cleaner, up into the chamber of the nailer. Tip it with the open rear facing down to allow the cleaning agent to run out, taking oil and grime with it. Run a cotton swab around the interior of the chamber. Repeat the application of the cleaner if the cotton swab comes back black. Allow the cleaner to evaporate for fifteen minutes.
What is the problem with staple guns?
Staple guns come in manual, electric, and pneumatic versions. The most common problem with all of them is jamming. There are different techniques for unjamming these disparate tools, although the theory is similar for all of them.
What happens if staples are ejected?
If staples are ejected two at a time or crooked, there could be something blocking the hammer mechanism. Remove debris, dirt, or fuzz from the hammer’s path. With the tool disconnected from any power source, a flathead screwdriver often works to push unauthorized particles out of the tool and away from the hammer.
Can a nail gun impale your leg?
It would be unfortunate if your nail gun came back to life just in time to impale your leg. You should already be wearing eye protection, but if not, be sure to put on protective goggles before you attempt a fix for a jammed staple or nail gun.
Can you disconnect power from a staple gun?
Disconnecting power isn’ t an issue with a manual staple gun, but you should still use caution about which direction you are pointing the tool and how you are handling the trigger until you have all the staples out.
Do staple gun staples need lubrication?
The hammer on a staple nail gun requires occasional lubrication. Use only the manufacturer’s recommended product. Lubrication will help the tool run more smoothly, but oil and grease can attract dust, fuzz, and dirt. If staples are ejected two at a time or crooked, there could be something blocking the hammer mechanism.
Jamming
Whether you’re working with an automatic, pneumatic, or electric staple gun, one issue you’re sure to have with all of them at some point is jamming. So, let’s take a moment to explore what constitutes a jammed staple gun. Jams usually occur when staples get cramped, bent, or wedged in the very top of the gun head.
Solutions for Jamming
Luckily, unjamming an industrial automatic stapler is relatively simple when you carefully follow the steps. The process is going to look a little like this:
Dispensing Too Many Staples at Once
Another issue that occasionally plagues staple guns is the tool trying to dispense more than one staple at a time. So, when you go to fire your gun and find you can’t secure your materials because several staples are falling out of the nose, then you’ve got a problem.
Solutions for Dispensing Too Many Staples
Take a moment to evaluate certain aspects of your staples and your gun. This can be beneficial in understanding how to fix it. Of course, just like any other kind of jam or blockage, you should first disassemble the gun and empty it.
Clogged or Misfiring Hammer
Clogged or misfiring hammers don’t exhibit themselves as obviously as you might expect. However, if you know what to look for, these issues can be much easier to address. You might have a clogged or misfiring hammer if your gun is doing any of the following things:
Solutions for a Clogged or Misfiring Hammer
So, when you start to notice these kinds of issues with your tool, it’s crucial to do everything you can to resolve the issue quickly. Again, when a staple gun is blocked or jammed, it’s best to start by disassembling it and checking for problems that are easier to fix. Then, check if you’re using the proper size and caliber staples for your tool.
Inadequate Depth Penetration
Of course, your staple gun can also be tricky when it comes to properly penetrating your materials. The entire purpose of a staple gun is to secure your projects efficiently and adequately with staples.
How to get rid of staples in a staple gun?
Use staples of just the correct sizes for the specific staple gun. Open the staple gun to get rid of the bar of staples. Slide this spring back and forth to ascertain that the staples may be forced out freely. Use a butter knife or a flat-head screwdriver to get rid of the visible staples.
What is a staple gun?
A staple gun is a larger version of your ordinary office stapler. Unlike the office stapler that is used to drive down pins in stationery, this one is used to fix the metal staples in materials of various kinds. This item finds much use in the fields of wood, plastic, and masonry. As with any other piece of equipment, ...
Why do staples jam?
These jams simply clog and subsequently impede the smooth movements of the staples. In doing that, they may also pose permanent and irreversible damages to the machines altogether.
What happens if you use a clogged stapler?
Clogged Hammer. If you use inappropriate staple sizes, there is bound to be the emergence of the clogged hammer. The tinier bits and pieces of the staples get to the crevices within the head of the hammer. This in turn causes the said portions of the gadget to clog.
How to prevent staple jams?
Staple jams are prevented mostly by slotting in only a few staples at a time. This is to give the machine ample space to release the staples one at a time. Also, it is important to skim the staples and see to it that they are smooth and uniform before using the same.
What happens when a staple gun spring wears out?
With use, the spring of this staple gun becomes worn out such that it is incapable of maintaining sufficient tension. If and when this happens, the spring cannot generate enough force to fire new staples going forward.
How to reverse menace?
Follow these steps to reverse the menace if and when it eventually arises: Test the spring of the staple gun. Slide the spring back to the fold and let go of it. It should contact the bar of staples rapidly. Replace the spring with a new one if it is too slow.