How To: Repair a Tent Pole
- You’ll need a broken pole, duct tape, and a tent pole repair sleeve (REI.com sells repair sleeves for 75 cents).
- A broken aluminum pole will usually crimp and shatter. If necessary, break off metal shreds and squeeze the flattened...
- For a quick midnight repair, slide the repair sleeve over the broken pole section keeping it centered...
How to repair a broken tent pole?
What to include in a tent pole repair kit:
- Extra shock cord
- Tent sleeve
- Duct tape
- Optional: guidewire, washers
How to fix a fiberglass tent pole?
- Get rid of the duct tape from the pole and sand the edges of the pole to get a smooth surface.
- Place the full pole of the tent on the floor and start to untie the knot on the end that is closer to the section that is to be replaced. ...
- Hold the shock cord and remove the pole sections carefully until you reach the broken part that is to be replaced.
How to repair aluminum tent poles! permanantly?
- Line up the broken/bent sections of the pole and straighten them out. ...
- Slide the sleeve over the end of your pole and center it over the bend. ...
- Sometimes the pole gets smashed and splays apart. ...
- Wrap around the splints using a liberal amount of duct tape or any other heavy-duty tape you have in your pack. ...
Is the pole the strongest part of a tent?
The four 10.25mm DAC Featherlite NSL green poles create a large symmetrical dome with tremendously strong sidewalls and lots of snowloading capabilities. The tent uses some of the strongest fabric found on any winter tent we've tested. Its tear strength is 40 pounds, yet weighs only 1.91 oz./yd.
How do you repair aluminum poles?
0:124:06Field Repair Aluminum Pole 11-25-10 Ten Minute Tent: - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere got your tube cutter in place here. I'm going to pinch down and give it a little twist.MoreHere got your tube cutter in place here. I'm going to pinch down and give it a little twist.
How do you fix a broken tent pole?
0:184:55How to repair a broken tent pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a spare but replacement Palmeri threading all the shock cord. So first of all we need a brokenMoreUsing a spare but replacement Palmeri threading all the shock cord. So first of all we need a broken tent pole. Oh. My god here's one I broke earlier. So you can see there.
How do you fix a bent aluminum tent pole?
The only way to soften the aluminum is to anneal it, which involves heating the aluminum almost to it's melting point and then letting it cool slowly, but if you try to do that then your pole will be so soft that it won't flex, it'll just bend like welding wire.
How do you fix a tent pole sleeve?
0:592:33How to Fix a Broken Tent Pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipCompletely unclip it and then slide the hub off the shock. Wave the tent pull out flat. And slideMoreCompletely unclip it and then slide the hub off the shock. Wave the tent pull out flat. And slide your sleeve over the damaged. Area. If you have duct tape firmly rabbet each side of the sleeve.
How do you fix a broken metal pole?
0:061:13How to Use a Pole Repair Sleeve | NEMO - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut by any sharp metal points if if they do happen to occur during that break. You're gonna slideMoreCut by any sharp metal points if if they do happen to occur during that break. You're gonna slide that pole repair splint right over the damaged area Center that damage in the splint.
Can tent poles be repaired?
The easiest and quickest way to fix a broken pole is with a pole repair sleeve. Also called a splint, this short tube is often provided with your tent. If not, buy one and pack it with you. A good pole repair sleeve is just slightly larger in diameter than your pole so that it doesn't move around too much.
Can you heat aluminum to straighten it?
When straightening aluminum, there are some temperature ranges that can be very effective. The general repair temperature guidelines are to heat the aluminum to a temperature range of 200-300°C or 400-570°F. Exceeding this range can approach the annealing temperature, which could compromise the strength of the metal.
How do you bend a metal pole back?
0:542:09How to Straighten Large Pipe or Tubing - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo it's kind of not that too bad an angle but try and get the bend in the masts. Pointing down andMoreSo it's kind of not that too bad an angle but try and get the bend in the masts. Pointing down and now I'm going to start putting some pressure on the jack.
How do you straighten a hollow metal pole?
Turn the handle of a bench vise counterclockwise to open the jaws wide enough to fit the diameter of the bent rod. Slide one end of a bent rod in the vise jaws. Align the bent section on the rod with the top of the vise jaws. Turn the vise handle clockwise to secure the rod in the vise.
Can you use Gorilla tape on a tent?
Tough and Wide Gorilla Tape (Quick & Dirty Fix) The best way to quickly and efficiently repair a tent while out camping or in the backcountry is with some Gorilla Tape. Gorilla Tape works as a strong seal to keep the tent together, semi-waterproofed, and enclosed.
How do you repair a Coleman tent pole?
1:1212:48How to Repair a Broken Tent Pole - Coleman Replacement Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst I will line up an old pole section with a mirror on and make a mark for the cuts. TheMoreFirst I will line up an old pole section with a mirror on and make a mark for the cuts. The instructions recommend wrapping a bit of tape. Next to where you will make the cut to prevent fraying.
How do I fix my Coleman tent pole?
3:0712:48How to Repair a Broken Tent Pole - Coleman Replacement Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe have a nice replacement pull section cut down to the right level a quick note about the shockMoreWe have a nice replacement pull section cut down to the right level a quick note about the shock cord if I really wanted to I could probably salvage the old cord and reuse it in the repaired pole.
How do you attach a ferrule to a tent pole?
The best adhesive to use to attach the aluminum ferrules to then ends of the fiberglass tubes or rods (or any tube or rod that is smaller than the ID these will accept) is JB Weld, Original Cold-Weld Formula. Mix the epoxy then apply a generous layer around the end of the tubing or rod.
How to fix a broken tent pole?
Using a repair sleeve to fix a broken tent pole is simple: Line up the broken pole sections. If the pole is bent but not fully broken, gently straighten out the bend. Slide the sleeve over the pole end until it’s centered over the break or kink; you might have to use pliers to crimp or a rock to bend splayed pieces so that ...
What to do if a tent pole gets stepped on?
Whether your tent pole gets stepped on or a powerful gust of wind does the damage, a kinked, split or snapped pole needs immediate attention in the field (when you get home, you can look into having the pole replaced or professionally repaired.) You have two options: Use a pole repair sleeve. Use a tent stake as a splint.
How to tie a shock cord?
Tie a knot in one end of the shockcord, then feed the other end through all but the last pole section. Stretch the shockcord to extend its length, then tie a temporary knot to keep it from slipping back inside the second-to-last pole section; alternatively, you can use a pair of locking pliers to hold the cord.
How to replace shockcord on tent pole?
Fortunately, replacing it is a straightforward process. Here’s what you’ll need: Here’s how to replace the shockcord: Start by laying the tent pole out straight. To avoid mixing up sections, you can label them with a permanent marker (use masking tape if you don’t want to write directly on the pole.)
What happens if a tent pole breaks?
If your pole breaks where one pole end inserts into the next one, you will have to splint the sections together; keep in mind that this will prevent the poles from folding up neatly when you take the tent down.
What is a splint for a tent pole?
Also called a splint, this short tube is often provided with your tent. If not, buy one and pack it with you. A good pole repair sleeve is just slightly larger in diameter than your pole so that it doesn’t move around too much. Using a repair sleeve to fix a broken tent pole is simple: Line up the broken pole sections.
Can you use a shockcord pole in the field?
If the shockcord snaps while you’re in the field, you can still use the pole by carefully assembling the individual sections. However, when you get home, you’ll want to replace the shockcord; it makes assembly simple and keeps you from losing a pole section. Fortunately, replacing it is a straightforward process.
What happens if a tent pole breaks?
A broken tent pole could cause your hopes for a perfect camping trip to come crashing down around you—literally. Unless you know how to perform a few basic repairs, that is.
What to do if you don't have access to a pole?
If you don’t have access to either of these furnishings, set the pole on top of a flat piece of gear , such as a cooler or toolbox. A smooth rock or level stretch of ground will also work in the worst-case scenario. There’s no need to disassemble the pole or remove the elastic shock cord that holds it together.
What to use instead of a repair sleeve?
If you don’t have a repair sleeve at the ready, a tent stake or sturdy stick can serve as an acceptable substitute. Tip: While it’s not necessary to take the pole apart in order to maneuver the sleeve into place, it may be easier to do so. ...
How to remove old cord from a pole?
Cut the anchor knot on either end of the pole to remove the old cord. Insert a pair of needle-nose pliers into the open end of the pole to fish out the knot. Use a sharp knife or pair of scissors to cut the cord just below the knot and snake it out of the jointed pole segments.
How to anchor a replacement cord?
2. Tie a knot in one end of the replacement cord to anchor it. No need to get fancy—just pick a point 4–6 inches (10–15 cm) from the end of the cord and loop it into a simple double overhand knot. Afterwards, give the knot a couple hard tugs to confirm that it’s tight.
How much tape should I use to wrap a split?
Cover the entire length of the split with 1⁄4 – 1⁄2 inch (0.64–1.27 cm) of tape. This will leave you with 1⁄2 – 1 1⁄2 inches (1.3–3.8 cm) of reinforcement, depending on the width of the roll you’re working with. Taping a split lengthwise is far more effective than simply wrapping the ends.
Do you have to disassemble a pole?
There’s no need to disassemble the pole or remove the elastic shock cord that holds it together. Take a moment to clear your work surface of leaves, twigs, pine needles, sand, and similar debris. If these items find their way onto your tape, they could compromise its ability to stick properly.
How do you Rethread camping poles?
A: To rethread a camping pole, you need to find the metal ring at the end of the pole. On one side of this ring is a screw that needs to be removed. Once it has been removed, slide the metal ring off and put it on the other side of the pole. Then tighten the screw back in place.
How do you straighten bent aluminum tent poles?
A: There are a few different ways to straighten bent aluminum tent poles. The first is to use a propane torch, which is the most effective way of straightening them. Another option is to use an angle grinder with a cutting disc attached, but this method can be dangerous and should only be done by professionals.
What is shock cord used for?
A: Shock cord is a device that is used to hold the handle of an umbrella or other similar object. It is typically made out of rubber, and it has a metal wire inside it that can be tightened by twisting.
How do you tie a shock cord?
A: To tie a shock cord, you will need to use a square knot. First, make a loop in one end of the rope and then cross it over the other end. Then, take that side and pass it through the loop you just made. Finally, pull on both ends of the rope to tighten up your knot.
How do you set up a tent by yourself?
A: It is best to start by finding a flat surface that you can set up your tent on. Next, find the center of the area and place your stakes in the ground. Lastly, tie the corners of your tent to these stakes using ropes or string.
How do you set up a two pole tent?
A: To set up a two pole tent, you will need to find the center of your tent and then place one stake in each corner. You will then need to attach the poles to these stakes using the grommets on the ends of the poles.
How do you use a tent pole splint?
A: A tent pole splint is a type of splint that is used to immobilize the wrist and hand. It is typically made from aluminum or fiberglass, and it is usually held in place by straps. The splint can be adjusted to fit any size hand.
Step 2: Getting Started
Cut the knot off on one end of the elastic and remove the poles from the elastic .
Step 3: Cutting to Length
Mark the length of the old pole next to the new pole. Hold the new pole firmly and very slowly cut the pole to size making sure not to tear the fibers . WEAR A MASK WHEN WORKING WITH FIBERGLASS .
Step 4: Sanding
Slowly sand the top of the pole to remove any splinters next sand the edges to a cone shape until smooth . Test fit the poles to make sure they fit snugly into each other .WEAR A MASK WHEN WORKING WITH FIBERGLASS .
Step 5: Threading the Elastic
To thread the elastic knot one end of the elastic and tie the fishing line to the knot free end you will need roughly twice the length of the pole in fishing line then just tie the needle on the end make sure the knot s small enough to fit inside the pole freely .
Step 6: Last Pole
You will have to pull the elastic tight through the last two poles so hold it around your finger then tie a double knot at the end of the elastic cut off the fishing line and its done .
