- Prepare the Antlers Near the broken area you will want to wash off any dirt or dried blood. I like to gently wash the...
- Mix the Epoxy The epoxy material was a little stiff so I warmed the tightly sealed containers in a cup of hot water...
- Form New Tines I wrapped the mixed epoxy material around the wire coat hanger a little at a time until I had a...
Full Answer
How do you fix broken antler tines?
First, determine the length needed and cut a piece of 10-gauge wire to the length plus an inch and a half that will be imbedded in the antler. Drill a hole in the antler and secure the wire with 5 minute epoxy. Once the epoxy has cured, bend the wire to match the curve of the other tines. Next mix up some Fixit Paste.
How to take care of Old Deer antlers?
Now the antler should have a natural matte appearance. Some bucks will have areas that are totally white, like around the antler tips. For this, use a wire brush to remove the stain. Then let the antlers dry for an additional 24 hours. Taking the time to breathe life into aging antlers allows you to remember the hunt for years to come. ■
How do you fix a bent wire on a deer antler?
Drill a hole in the antler and secure the wire with 5 minute epoxy. Once the epoxy has cured, bend the wire to match the curve of the other tines. Next mix up some Fixit Paste.
Can antler tines be replaced?
This is the 1st in the series for Antler Repair. In the taxidermy field, we often encounter broken tines or points as some would call them. Often clients will want these replaced to restore their trophy to its pre-break grandeur. Following are some different techniques for antler restoration.
How do you fix broken antler points?
1:178:23Broken Antler Repair Using Apoxie Sculpt - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut not too stiff that you can't bend it a coat hanger works great what we're going to do is justMoreBut not too stiff that you can't bend it a coat hanger works great what we're going to do is just drill a hole into where it's broken off so that that piece of wire can go down in. There.
What glue is best for antlers?
Epoxy glueFor gluing combinations of bone/antler material and metal (e. g. for knife handles) Epoxy glue (No. 450382) should be used. It is transparent and gap-filling, and is therefore also ideal for gluing spongy surfaces.
How do you fill holes in antlers?
1:447:05Easily patch holes in antlers & darken whitened antlers - YouTubeYouTubeStart of suggested clipEnd of suggested clipInteresting the whole sort of scroll go in so you can cover it. Up. Save those shavings get theMoreInteresting the whole sort of scroll go in so you can cover it. Up. Save those shavings get the bigger chunks.
How do you rejuvenate antlers?
1:183:33Color Old Deer Antlers | How to use COFFEE to Restore ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo concentrate your coffee grinds in the middle and the base of the antlers. Once your antlers areMoreSo concentrate your coffee grinds in the middle and the base of the antlers. Once your antlers are dry you can use your steel wool to lighten any dark spots by buffing them. Out.
Does Super Glue work on bone?
Stewart says some synthetic superglues or “instant glues” are used instead of sutures for superficial skin wounds. But because of toxicity or toxic byproducts, “they are not suitable for deep tissue use,” including bone repair, he adds.
What glue is used in taxidermy?
Cyanoacrylate Super GlueCyanoacrylate Super Glue for Taxidermy Cyanoacrylate (CA) or super glue is great for gap filling. Using a think viscosity or gel super glue makes gap filling for your taxidermy projects easy.
How do you touch up deer antlers?
0:007:58How To Touch Up Antlers When Doing A European Skull MountYouTubeStart of suggested clipEnd of suggested clipIt doesn't matter what method you use I've used beetles. And degreasing or bowling. You're alwaysMoreIt doesn't matter what method you use I've used beetles. And degreasing or bowling. You're always gonna have on some deer you grab discoloration at the bases the antlers.
How do you get the color back in deer antlers?
Registered. Formula #10: antler stain Use to restore a natural color to bleached, or faded antlers. Dissolve 1/2 teaspoon of potassium permanganate crystals in 1/2 cup of warm water. Apply this to the antlers with a brush or wad of cloth until the desired color is attained.
Can you use wood stain on deer antlers?
1:267:28DIY: Restore Sun-Bleached Antlers with Wood Stain - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a school I'm going to show you you can tell the Sun is drained old old life basically out ofMoreThis is a school I'm going to show you you can tell the Sun is drained old old life basically out of this antler just this dead deer that we found a few years back or you can even do a shed. So you
Can bones be glued back together?
antlers may not crack indoors but they certainly get very dry...the mineral oil puts the life back in em... I just experimented with a couple a year ago...they look much more vibrant than those I didn't apply it on... many taxidermists suggest everything from liquid gold to old english on them...Mar 26, 2018Mineral oil on antlers | Rokslide Forumhttps://www.rokslide.com › forums › threads › mineral-oil...https://www.rokslide.com › forums › threads › mineral-oil...Search for: What oil do you use for deer antlers?
How do you glue wood to bone?
Boil the antlers outside. This step is important for removing dangerous bacteria from the antlers. You should boil the antlers outside, otherwise they will stink up your house. Before beginning, test to see if the cooking pot is large enough to fit the antlers inside.How to Clean Deer Antlers: 8 Steps (with Pictures) - wikiHowhttps://www.wikihow.com › Clean-Deer-Antlershttps://www.wikihow.com › Clean-Deer-AntlersSearch for: Should I boil deer antlers?
How strong is Gorilla glue Epoxy?
Spray a clear coat of polyurethane onto all parts of the antlers to protect them from water and insect damage. This spray also helps preserve the natural colors of the antlers.How to Prepare Deer Antlers - Gone Outdoorshttps://goneoutdoors.com › prepare-deer-antlers-6700207https://goneoutdoors.com › prepare-deer-antlers-6700207Search for: Can you put polyurethane on antlers?
How do you use bone glue?
A new study out of Sweden has found that doctors maybe able to glue broken bones back together. Dr. Dave Shukla was interviewed by The Doctors to help explain. While it's very early to say, Dr.
Amy Mammal artist
Ok, I have done some minor antler fixes in the past but nothing to this extent. I would very much appreciate some help here. I have a customer who shot this very nice whitetail, but as you can see, it was a fighter.
Paul B Active Member
Its not to hard of a job, but the time involved, you could probably get the deer mounted faster. As Bucknut said, Fix It works good, nice base color for bone. I have a few "junk racks" I keep just for this reason, tine replacement.
Matt Active Member
Thanks Haffs, Amy check out that tutorial and let me know if you have any questions. I do a lot of beam repair these days, but this one was a bit extreme.
Mac McLane Member
Just like Matt, I am doing more antler repair. In an area where shotgun is the primary used firearm you get antlers shot off. I will repair a couple of different ways but the way I prefer is to add real antler vs rebuilding completely. I collect sheds and antlers from guys who no longer want them and will cut tines that closely match existing.
Jerry Huffaker Well-Known Member
We get 25.00 per inch. I mold and cast all of our tines out of plastic these days, don't use epoxy puddys anymore.
Jacob N. Member
I charge $10 an inch, but I have a min of $45. Just because it is as easy to replace a point that is 10" as it is to replace one that is 5". Like Jerry I cast my points and replace with plastic. To me it is easier to hide the transition that way. I have used real antler before but that way makes it alot harder to get it to look good.
Amy Mammal artist
Thank you SO much for advice y'all! That tutorial was amazing and very helpful. Awesome job, Matt!! If you can recreate an entire side, surely I can do this project! The fix it looks like the ticket. I like sculpting and having the freedom to shape things how I like.
Who is the antler repair guy?
Mention the name Tom Sexton to anyone who knows him even casually, and chances are you'll get a long response from that person about what a great human being the man is. During his long career he's helped literally thousands of taxidermists become better artists in their own right, and he's also helped hundreds of sportsmen and antler collectors with his amazing works of perfection. Truly, Tom Sexton is a one of a kind in the whitetail industry!
How many points did Tom get from his antlers?
One such set of antlers received by Tom had 46 individual points. The heavy rack had been sawed off the live buck out of necessity after it reached full growth due to the animal's inability to lift its head.
What percentage of Tom's business is repairing whitetails?
About 70 percent of Tom's business consists of repairing broken tines and main beams on trophy whitetails taken by hunters. He often replaces entire left or right sides that have been snapped off in rutting battles. Though some hunters prefer leaving a buck's broken rack as it was when harvested, most favor restoring the rack to its original beauty.
What year did Brian Andrews arrow a 26 point buck?
Without question, one of the most challenging projects in Tom's multi-faceted career involved the recent replication of the Brian Andrews buck. On Nov. 14, 2003, then 16-year-old Brian Andrews arrowed an incredible 26-point buck near his home in Independence, Iowa. Brian's buck became an overnight sensation. With a score of 253 1/8 non-typical points, it became a new state-record non-typical by bow. Sadly, Brian's mounted trophy of a lifetime was stolen from his home in June 2004. (See the September 2004 issue for Brian's complete story. Also see the September 2008 issue for an update on Brian's stolen rack. To date, the rack has not been recovered.)
Is Joe's rack repair job flawless?
The repaired rack was flawless. Neither Joe nor his client could identify a broken joint or pick out a color imperfection on the entire rack.
How to make a paint look brown?
Use a drop of burnt umber, and smear it out thinly on your palette. Use the same flat hard bristled brush and barely tip it with umber. Jab the very tip of the brush on to the painted surface in a pattern consistent with the brown you see on the other tines. Clean the brush every two or three jabs. Once the umber is in place, use a soft, flat hair bristle brush and lightly stroke the painted area to blend and smooth the paint. Keep the brush clean. Stroke one side, turn over and clean. This will help keep from turning the colors “muddy”.
Can apoxie be used over body filler?
I have never had any problems with adhesion when Apoxie Sculpt has been applied over a body filler. Using the same techniques as described above, and then using Apoxie Sculpt to create beading or any other shapes needed, a person can pull off some rather extensive repairs.
