How do I fix a corrupt BIOS?
In some cases, you may be able to fix problems with a corrupt BIOS by updating the BIOS. Make sure your computer has a consistent power source when you updating your BIOS. If the update process is interrupted, it can cause permanent damage to your computer. You will need to know which version of BIOS you are running.
What to do if the BIOS is not responding?
Try to reflash the BIOS either by using a bootable flash drive or by taking it to a computer repair specialist. 5. Check if the BIOS chip can be replaced. 6. Purchase a new BIOS chip and replace it if possible.
How do you fix a crack in the subframe?
This mimics the look of the factory subframe. We also drilled 2 holes for the spot welds, just like the factory. Locate each crack, find where it stop and drill the end with a small drill bit. A 1/8-inch bit usually large enough to do the job. The goal here is to remove the stress factor so that the crack does not continue.
Why are B-bodied cars so hard to repair?
Add to the potential rust issues, the K-member bolts to the subframe as well, and the hard lives these B-bodied cars have often been subjected to leads to cracks. All of these are potentially deadly situations, so it pays to be careful. Repairing this type of damage depends on what and where the damage is.
How do you fix a computer that won't boot up?
Double-check the AC adapter. If your laptop isn’t turning on, double-check that the AC adapter is functional and connected properly to the machine....
Can a computer screen be fixed?
Yes, but it will depend upon the model how easy it is, how much it will cost. Laptops with easy to replace screens still exist, but are becoming le...
How do you troubleshoot a computer?
That depends on the type of problem that you're having, but you can check out which can help you with many common problems.
How to repair a K member?
For the K-member mount, this meant the bumpstop brackets that are spot welded to the frame. Using a drill bit or Rota-broach cutter, the spot welds are cut out and the bracket removed in one piece. This will be reused, so don’t trash it or grind it off. Using a grinder with a flap-wheel or a die-grinder with a Scotchbrite pad, clean off the frame and trim up any jagged edges on the damaged area. All of the undercoating and paint needs to be removed so you can find any and all of the cracks on the steel.
What is the B body of a Mopar?
The classic Mopar B-body has some of the best lines of the muscle car era. Unfortunately, the B-body also has some of the worst potential damage areas too, some of which can remain hidden for many years, only to be found when the damage is too severe for simple repair. The front subframe is one such area.
How to stop warping on sheet metal?
Once the repair was welded in place, the cracks were welded up. Keeping the welds down to 1-inch increments is a good idea. Not only does this help reduce warping, but also reduces the potential for burn-through on the relatively thin sheet metal.
What happens to the top of a subframe?
The top of the subframe is open along several places on the body, allowing dirt and water to collect inside the subframe. Eventually, the steel rusts through, leaving the uni-body structure in bad shape.
Can you repair a subframe?
Repairing this type of damage depends on what and where the damage is. Replacement subframes are available, but they are expensive and the installation process requires massive surgery on your car. Often, you can get away with simply rebuilding the affected area with a home-made patch.
How to fix memory error?
Reset the RAM. Try carefully removing the ram and powering on. Most computers, when functioning properly, will give a long, repeating 'memory error' beep. Power off and replace the ram, one stick at a time. Powering on when ram is properly seated.
How to fix a computer that is flashing?
If you leave your computer on all the time, you can often fix a problem by turning shutting down the computer, then unplugging it. Then holding down the power button for 30 seconds while the computer remains unplugged. This may cause the LED lights to flash. Plug the computer back in and power it on. By cutting off the power to the motherboard, it allows the hardware to reset and the memory to clear.
How to fix a laptop that won't turn on?
Double-check the AC adapter. If your laptop isn’t turning on, double-check that the AC adapter is functional and connected properly to the machine. Try plugging the AC adapter into another electrical outlet. Try using another compatible AC adapter or power cord. If the AC adapter is fine, you can try finding a schematic of the computer online and see if you can short where the power button attaches and get power running through the machine.
What to do if your computer won't power on?
Replace or repair your computer. If you've tried everything and your computer will not power on or boot up, you probably need to have your computer repaired or replaced. If you have an older computer, it may be cheaper to buy a new computer rather than have it repaired.
