Repair a Blender
- Taking It Apart. Technically, the first step to repair was waiting for a while. ...
- Examining and Testing Internal Components. With the top cover off, the first thing noticed was a small yellow block. ...
- Accessing and Testing the Fuse. To get access to the fuse required removal of the switch. ...
- Replace Fuse, Insulation and Case. After an afternoon of driving around, I sourced a replacement. Thank you Jaycar! (Other suppliers are available.
Why is my Blender not working?
Why Blender Stop Working? The blender will not work properly if the power setting is too low. A faulty switch or damaged motor can also cause the blender to stop working. The blade will not turn properly if the drive stud is loose or worn out resulting in the malfunction of the blender.
How to open and repair hand blender?
To tighten the drive stud:
- Remove the base and turn the blender over. The other end of the drive shaft will protrude from the bottom side of the motor.
- Grip the drive shaft with a wrench or pliers, then turn the blender on its side to attach a wrench to the drive stud.
- Hold the drive shaft steady as you turn the drive stud clockwise.
How to make Blender fully portable?
Product Description
- Fully charge your blender for 2~3 hours when first using.The blender cannot work when charging. It can be charged by power bank, adapter, car charger, computer USB port etc.
- Double-click the switch to work, click the switch to stop working
- Please clean it after receiving the goods. ...
How to fix a blender?
How to Repair a Food Blender. Food blender repairs include servicing a multispeed switch, replacing a fuse, servicing a motor, tightening a drive stud, and servicing a blade assembly. Servicing the Multispeed Switch: It's easy to see why the multispeed switch is a critical component to the operation of your food blender. Because of its high use ...
What to do if blender stops working?
Blender not working? Here's how to fix itCheck for power connectivity. You can check for power connectivity if blender not working. ... Clean the terminals. Another thing you can do to fix a blender which is not working is to clean the terminals. ... Check the fuse. ... Make sure the blender is not jamming. ... Do a final check.
Why is my blender not blending?
There may be times when an air pocket is created around the blade, causing the ingredients to miss the blending blade. Unplug the power cord. Remove the Blender Jar from the base, and use a spatula to rearrange ingredients in the Blender Jar. Turn the Blender on to continue use.
Why is blender not spinning?
Most of the time when your blender is powered on and the blades will not rotate, it is because you have overfilled the container. Remove some of the food/liquid and try to power on your blender again.
How do you fix a blender base?
0:481:40Replacing the Container Bottom (Oster Part # 148381-000-090)YouTubeStart of suggested clipEnd of suggested clipMake sure you line up the threads. So it doesn't cross thread. And don't over tighten it or you'llMoreMake sure you line up the threads. So it doesn't cross thread. And don't over tighten it or you'll crack the base. And I'll place this back onto the blender.
How long should a blender last?
How long do blenders last? In general, less-powerful blenders will last three to five years, while more expensive models with a powerful motor will last about 10 years. However, how often you use your blender will impact its lifespan.
How do you know if your blender is broken?
5 Signs It's Time to Replace Your BlenderIt stops midway through blending. This is pretty much an obviously sure sign it's dead. ... The motor is slow or inconsistent. ... The cord is starting to fray. ... It's leaking. ... You want a blender that does more.
Can a blender overheat?
From smoothies and sauces to facemasks and body scrubs, blenders see tons of action. Regardless of what gets diced up in your blender eventually, you may notice it start to overheat. Overheating can present itself in a few different ways, but the bottom line is that it's not a good thing.
Why is my rechargeable blender not working?
The most common reasons a portable blender will not work are a lack of charge or an overload. Be certain that you have properly charged the portable blender before use. A solid red light on most models means that it is fully charged and ready to blend.
What are the parts of the blender?
The parts of the blender, from top to bottom, are the lid, jar, blades, gasket, jar base and housing. The individual, and often replaceable, components of a blender are pretty basic and consist of the following: Housing. Blade.
Can blender be repaired?
Food blender repairs include servicing a multispeed switch, replacing a fuse, servicing a motor, tightening a drive stud, and servicing a blade assembly. Servicing the Multispeed Switch: It's easy to see why the multispeed switch is a critical component to the operation of your food blender.
How do I fix a leaky blender?
0:2113:17Leaking blender? How to fix it yourself - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet somebody to grab the bottom or you could possibly grab it between your legs. And then turn thisMoreGet somebody to grab the bottom or you could possibly grab it between your legs. And then turn this part usually it's counterclockwise. Nice part easy because I just took it apart.
Why does my blender smell like it's burning?
Blenders with heavy use will have worn out brushes over time. The brushes will arc, resulting in a burning smell and possibly some smoke. The carbon brushes are used in electric motors to transfer electricity to the armature inside the motor. Brushes wear down over time and stop coming in contact with the armature.
Can you put frozen fruit straight into a blender?
While they're delicious and easy to make, people sometimes put fully frozen fruits in the blender. This can result in lumpy smoothies and, in some cases, can cause the sharp blades to crack and break. Leave frozen fruits out in the fridge to thaw or put them in a Ziploc bag and thaw in a bowl of water before blending.
Why does my blender not blend frozen fruit?
Combining smoothie ingredients in the wrong order can cause frozen fruit and ice to get caught in the blender's blades. Start by adding the yogurt, or a base liquid such as water, juice, or milk, to the blender.
Why is my Ninja Blender not blending?
Unplug the Ninja, then inspect the blade assembly and the base. If there is any buildup, this might be your problem. Gently and carefully clean the assembly, then try again. You can avoid most of these issues by properly cleaning your Ninja brand blender thoroughly after each use.
Why is my portable blender not working?
The most common reasons a portable blender will not work are a lack of charge or an overload. Be certain that you have properly charged the portable blender before use. A solid red light on most models means that it is fully charged and ready to blend.
How to tighten a blender drive shaft?
To tighten the drive stud: Step 1: Remove the base and turn the blender over. The other end of the drive shaft will protrude from the bottom side of the motor. Step 2: Grip the drive shaft with a wrench or pliers, then turn the blender on its side to attach a wrench to the drive stud.
How to test a blender motor?
To test a blender's motor: Step 1: Place a probe on each cord prong. Step 2: Select a speed-control button or turn the speed controller slightly, then read the resistance on the meter. Step 3: Next, rotate the drive stud clockwise one turn. If the resistance reading (in ohms) changes, the motor needs service.
How to check if a fuse is working on a blender?
To determine if the fuse is working: Step 1: Remove the blender base and locate the fuse in the wire from the multispeed switch to the motor. Step 2: Disconnect the wire and use a continuity tester or multitester to check the fuse. If the circuit is open, the fuse is blown.
How does a multispeed switch work in a blender?
The multispeed switch in the blender sends current to the motor based on which control buttons are selected or how far the rheostat is turned. More current means a higher motor speed. Placing hard foods in the blender jar ...
Why does my blender burn out?
More current means a higher motor speed. Placing hard foods in the blender jar and trying to chop them with a low motor speed can cause the motor to burn out. Because the jar holds liquids, yet must be disassembled for cleaning, it has seals to keep liquids from escaping.
Why does my blender chop food?
A blender's blade assembly blends or chops food in the jar. The most common problem is caused by the jar leaking liquids. The solution is to tighten the base. If this doesn't solve the problem, inspect and, if necessary, replace the gasket.
What is the cross section of a blender?
The cross section of a blender. A food blender is a popular and useful kitchen appliance. Foods and liquids placed in it are blended or chopped based on the speed set by the operator. Today's food blender can chop ice, make peanut butter, grate cheese, and perform many other useful functions.
What Can Go Wrong with a Blender?
Because blenders are simple motorized small appliances, the things that can go wrong also are simple. The electrical cord, motor, switches, or fuse may fail. Parts may become loose or worn and seals may leak. (To avoid spills, don’t fill the blender jar more than two thirds full when in use.)
How Can I Identify a Blender Problem?
If the blender doesn’t work at all, make sure power is on at the outlet. Check the electrical cord. Test the fuse with a multimeter. Test the multi-speed switch (see the Appliance Controls Fix-It Guide ). If all this fails you’ll need to test the universal motor.
What Do I Need for Blender Repair?
Replacement parts are available from the manufacturer or aftermarket supplier. These are the tools you’ll need for disassembly and repair:
What Are the Steps to Blender Repair?
Wear a leather glove to hold the fan in place as you disconnect it from the motor shaft.
How to fix a blender that is leaking?
To fix blender leaking from the bottom, remove the gasket and clean it thoroughly after drying it place it tightly in its position and run the blender to check. Jam or overload gasket is another cause of black liquid. Check the blending jar bottom either it’s crack or not.
How does a blender work?
Blenders work with their blades linked to the motors. The link is a metal stud or coupling that attaches the blades with the motor . As long as these two are free to rotate there won’t be any problem. But over time the blender could be overloaded. Here is how you can fix your blender.
How to replace a jar coupling?
Hold the cap nut with taped pliers and start to replace the jar coupling. Now turn the coupling clockwise to and slowly remove it. If the condition indicated to replace the motor coupling, hold the motor shaft with pliers and unscrew it. After fining all the replacement or coupling units flow all these steps backward to assemble the blender.
How to check if blender is low?
Step 1. Check your blender with a volt-ohm meter with its RXI scale. Before that unplug the blender from the socket and turn the power switch on. Now the clip the clot-ohm meter probes to the plug prongs. Now press the speed switch of the blender, chances are you will see a low reading in it.
How to clean a motor blade?
Take an old toothbrush and scrub it carefully. After cleaning it with water dry it with a paper thoroughly and use some white grease to lubricate it. Your blade should spin by hand how without any trouble. If so, it’s ready to work again with the motor.
How to get the smell out of a blender?
Remove the bottom cover of the motor while unplugging the power cord from the socket. Take a thick dry cloth to make barricade putting it on the middle where the motor and you are standing. Plug it back, run it on high speed until the smell coming back. Now unplug the blender again and remove the towel.
Can you keep accessories in a blender?
You can keep some accessories and use the parts when the blender goes to trouble. For the best blender performance, I request to keep the accessories bellow. If you want to best blender for your kitchen.
Step 1: Taking It Apart
Technically, the first step to repair was waiting for a while. There might have been a self-resetting safety mechanism inside the case, so I waited a few hours and then powered on the motor. Nothing happened, which gave me some confidence that there was an actual break somewhere.
Step 2: Examining and Testing Internal Components
With the top cover off, the first thing noticed was a small yellow block. Searching for the part number identified it as a capacitor. It didn't look to have any physical problems (distortion, holes, smoke stain) so I checked it with a meter and it looked OK. Time to push on.
Step 3: Accessing and Testing the Fuse
To get access to the fuse required removal of the switch. To remove the switch required access to two screws right inside the base of the casing. To get access to those screws required removal of the control knob. To remove the control knob, about four hands were required to bend and stress various plastic catches at the same time, which is why there is no photograph of that..
Step 4: Replace Fuse, Insulation and Case
After an afternoon of driving around, I sourced a replacement. Thank you Jaycar! (Other suppliers are available. They just don't carry 2A slow-blo)
Tools
These are some common tools used to work on this device. You might not need every tool for every procedure.
Background and Identification
A blender is a kitchen and laboratory appliance used to mix, puree, or emulsify food and other substances. A stationary blender consists of a blender jar with blade at the bottom, rotated by a motor in the base.
